Owner’s Manual
Model
ADAT/ANALOG Converter
OPTICAL
ADAT/ANALOG CONVERTER
CLOCK
ANALOG INPUT MODE
1-2 1-4 1-8
DIGITAL MODE
ADAT S/P DIF
POWER
STBY ON
75
WORD
OPTICAL INT(44.1k)
ON
OFF
LOCKED
Table of Contents
Safety Instruction..............................................................................................2
Introduction.......................................................................................................3
Precautions.......................................................................................................3
Outstanding Features.......................................................................................3
Names and Functions.......................................................................................4
Connecting Examples.......................................................................................5
Example at operating it as the ADAT-ANALOG converter......................5
Example at operating it as the S/P DIF-ANALOG converter...................8
Specifications....................................................................................................9
Model VC-8 Owner’s Manual
INTRODUCTION
Thank you very much for having purchased the Fostex Model VC-8.
The VC-8 is an adat/analog converter which allows connections to be made with adat optical exclusive
digital multirecorder such as the VR-800 and various analog mixers. In order to accomplish high
quality collaboration with analog mixers, the professional 20 bit type are employed for AD/DA.
Also, to build a most effective system matched with the number of analog mixer output BUSes (2 BUS
OUT, 4 BUS OUT, 8 BUS OUT) the INPUT MODE switch makes it unnecessary to reconnect the cables
at record/playback. Furthermore, the VC-8 can be used as a S/P DIF/analog converter, and by
connecting to the sound card contained in various computers with digital input/output, it will give
a clean record/playback environment free of internal noise generated in the computer.
Before operating VC-8, it is recommended to thoroughly read this manual to insure long life of this
equipment.
Precautions (please read before use)
Outstanding Features
Power supply
* A digital multiple system can be setup by using
the adat optical and analog in/out converter of
the VC-8 together with various analog and digital
mixers provided with adat optical such as the
VR800.
* When unplugging the AC adaptor from the outlet,
be sure to grasp the adaptor. Attempting to unplug
it by pulling on the AC cable may damage the
wiring.
* It is dangerous to use any power cable that is cut
or frayed. If the power cable is damaged,
immediately stop using it, and have it repaired.
* Due to employ of the professional 20 bit AD/DA
converter, it is possible in conjunctive operation
with the analog mixer without degrading the high
quality sound of digital recordings.
* Do not plug in or unplug the AC adaptor with wet
hands. Doing so may result in dangerous electric
shock.
* As the INPUT MODE is switchable, it is possible to
construct a system to match the number of BUSSes
in the analog mixer.
* Do not open the unit or touch any parts inside.
Doing so may result in a dangerous electric shock,
and could damage the unit.
* Additionally, as S/P DIF can be converted to the
analog inputs/outputs and vice versa, it can be
connected to the internal sound card of the
computer provided with digital inputs/outputs.
* Do not let water or other liquids, flammable
materials, or metal objects such as pins get inside
the unit. These things may cause electrical shock
or short circuit the VC-8, and damage it.
If the VC-8 should become wet, unplug the AC
adaptor from the AC outlet, and contact your
authorized service station.
* Either the internal (44.1kHz) or OPTICAL/WORD
(Phase adjusting range: 32~48kHz) can be selected
and thus it can be widely adapted to digital
equipment.
Location
* Avoid using the VC-8 in the following locations:
* Locations of extreme low or high temperatures, or
extreme changes in temperature.
* Locations with excessive moisture or dust.
* Locations where direct sunlight falls for an
extended time, or near a stove or other source of
heat.
* Locations where electrical voltage varies.
* Unstable locations or where there is heavy
vibration.
* Near strong magnetic fields (on top of a television
or speaker).
3
Model VC-8 Owner’s Manual
Names and Functions
ANALOG INPUT MODE switch
This switch is used to select the
channel to which the ADAT output
should be assigned for the signal
input to the ANALOG INPUT jack.
This switch will be active only when
the DIGITAL MODE switch is set to
ADAT. Refer to pages 6 and 7 for
details.
POWER switch/POWER LED
AC power to the VC-8 is switched
ON/OFF (or “standby”). If the VC-
8 is not to used for a long period,
the AC adaptor should be
unplugged from the wall AC mains.
WORD IN terminal switch
This must be switched ON
when the external WORD
clock is input.
OPTICAL
ADAT/ANALOG CONVERTER
CLOCK
ANALOG INPUT MODE
1-2 1-4 1-8
DIGITAL MODE
ADAT S/P DIF
POWER
75
WORD
OPTICAL INT(44.1k)
ON
OFF
STBY
ON
LOCKED
LOCKED LED
CLOCK selector switch
DIGITAL MODE selector switch
The DIGITAL MODE IN/OUT
formats (ADAT or S/P DIF) is
selected by this switch.
This indicates status
of the operating
clock selected by the
CLOCK selector
switch. Refer to page
6 for details.
The VC-8 operating clock (INT, WORD
or OPTICAL) is selected by this switch.
Refer to page 6 for details.
Refer to page 6 for details.
DIGITAL INPUT/OUTPUT connectors
There are connected to the VR800
digital multitrack recorder or to the
DIGITAL IN/OUT connectors of a digital
recorder provided only with digital in/
out connectors.
ANALOG INPUT connectors (1-8)
These are connected to BUS OUT
(or GROUP OUT) of the analog
mixer. Refer to pages 5 and 7 for
details.
8
7
6
5
4
3
2
1
IN
OUT
IN
AD-12A ONLY
OPTICAL
OUT
12V
8
7
6
5
4
3
2
1
DC IN
ANALOG
WORD IN
DIGITAL
DC IN jack (Center: Plus +)
ANALOG OUTPUT connectors (1-8)
WORD IN connector (BNC)
The external WORD clock
signal is input here.
The AC adaptor (AD-12A)
included with the VC-8 is
connected here. Do not use an
adaptor that is not soecified for
the VC-8.)
These are connected to the TAPE
INPUT jacks of the analog mixer.
Refer to pages 5 and 7 for details.
Refer to page 5 for details.
4
Model VC-8 Owner’s Manual
Connecting Examples
Example at operating it as the ADAT-ANALOG converter
The following connecting schematic is an example of locating the VC-8 between an analog mixer
with 8 TAPE IN - 8 BUS OUT (or GROUP OUT) and the VR800 (digital multitrack recorder). In this
system, the 8 BUS output from the analog mixer is converted to adat digital signals and the signals of
channels 1~8 can be recorded on tracks 1~8 of the VR800.
DATA OUT
DATA IN
OUT
MIDI
WORD OUT
SCSI
OPTICAL
IN
AC IN
POWER
DATA IN
DATA OUT
8
7
6
5
4
3
2
1
IN
AD-12A ONLY
VC- 8
OPTICAL
OUT
12V
8
7
6
5
4
3
2
1
DC IN
ANALOG
WORD OUT
WORD IN
VR800
Note: When connecting to a
digital recorder with WORD OUT
such as VR800, it always must
be connected to WORD IN of the
VC-8 and used by input of
WORD clock.
BUSS OUT (GROUP OUT) 1~8
TAPE IN 1~8
Analog Mixing Console
Sound sources
Note: When the digital inputs and outputs of the VC-8 and VR800 (or another digital recorder) are connected
as shown in above connecting schematic, be sure to set one side as the clock master and the other as the
clock slave.
In other words, if the VC-8 had been set as the master, then VR800 (or another digital recorder) must be set
as the slave, or if in the reverse situation whereas VC-8 had been set as the slave, then VR800 (or another
digital recorder) must be set as the master. The most recommended setting at using the VC-8 is to establish
the digital recorder as the master and the VC-8 as the slave as shown in table below.
VR800: Asynchronous mode
Other recorder: Internal mode
VR800: Synchronous mode
Other recorder: External mode
The most recommended setting. Furthermore, if the
WORD clock can be input, then WORD must be input.
Recorder
VC-8
VR800 (or recorder): Master
VC-8: Master
VR800 (or recorder): Slave
VC-8: Slave
This setting is employed if the recorder (general DAT and
MD) has an internal clock and thus cannot accept digital
signals.
CLOCK switch
INT (44.1kHz)
Mutual exchanged of digital signals between the equip-
ment is possible by this setting, but deterioration of sound
quality is unavoidable.
VR800 (or recorder): Slave
VC-8: Slave
VR800 (or recorder): Slave
VC-8: Slave
CLOCK switch
This setting cannot be used. Adigital loop will be created
in general type DAT and MD and thus will not operate
correctly.
WORD or OPTICAL
5
Model VC-8 Owner’s Manual
Setup of the VR800
1.Set the VR800 digital input track to [AdAt] and the digital in clock to [ASYnC](Asynchronous mode).
2.Set the VR800 digital output track to [AdAt].
Note: Refer to the VR800 Owner’s Manual for setups of the VR800 “Digital input track” and “Digital output track”
settings.
Setup of the VC-8
Note: Be sure to switch off power to the VC-8 at setup of the various selector switches. Should the switches be
manipulated with power switched on, noise could be created and the VC-8 may not function correctly.
OPTICAL
ADAT/ANALOG CONVERTER
CLOCK
ANALOG INPUT MODE
1-2 1-4 1-8
DIGITAL MODE
ADAT S/P DIF
POWER
STBY ON
75
WORD
OPTICAL INT(44.1k)
ON
OFF
LOCKED
5
1
4
3
2
1.Set the DIGITAL MODE switch to [ADAT].
4.Switch ON the terminating switch.
2.Set the ANALOG INPUT switch to [1-8].
If it is to be connected to a 4 BUS or 2 BUS mixer,
refer to next page.
5.Switch on power to the VC-8.
At this stage, as signals are being input to both
DATA IN and WORD IN, the LOCKED LED will be lit
in orange color.
3.Set the CLOCK switch to [WORD].
<The CLOCK switch and LOCKED LED>
The CLOCK switch is for selecting the required clock frequency and is selected in accordance to the application
as lited below. Depending on the application, the LOCKED LED indicates the type of digital signal that is
input and setting of the CLOCK switch.
CLOCK SW
WORD IN
OPTICAL
INT (44.1k)
WORD
OPTICAL IN
Lit in
green
Lit in
green
Extin-
Extin-
Lit in
Lit in
Extin-
Extin-
Extin-
guished
Lit in
green
Lit in
green
Extin-
guished
LOCKED LED
FUNCTIONS
guished guished orange
green guished guished
If the LOCKED LED is lit in green, If the LOCKED LED is lit in red or
the VC-8 will operate in sync with orange, the VC-8 will operate in
the digital signal input to the VC-8 sync with the word clock that is in-
DATAIN connector. If the LOCKED put to the VC-8 WORD IN connec-
LED is extinguished, it indicates that tor. If the LOCKED LED is lit in
no digital signal is being input and green or is extinguished, it is an in-
it will not operate correctly even dication that word clock is not be-
though switched to OPTICAL. In ing input and thus will not operate
such case, set the CLOCK switch correctly even though the CLOCK
Regardless to the LOCKED LED
indication, the VC-8 will operate
by its internal 44.1 kHz crystal.
to INT.
switch is set to WORD. In such
case, set the CLOCK switch to
OPTICAL or INT.
6
Model VC-8 Owner’s Manual
When connecting a 4 BUS OUT mixer
Connect the mixer BUS OUT to INPUT 1~4 of the VC-8 and select [1-4] of the VC-8 ANALOG INPUT MODE
switch. Signals input to ANALOG IN 1~4 will be assigned, respectively, to ADAT outputs 1~4 and 5~8.
In other words, the ANALOG IN 1~4 signals will be simultaneously sent to tracks 1~4 and 5~8, thus 4
tracks each can be recorded without re-connecting the cables.
8
7
6
5
4
3
2
1
IN
AD-12A ONLY
ATA
MIDI
WORD OUT SCSI
OPTICAL
OUT
IN
AC IN
POWER
OUT
OPTICAL
12V
8
7
6
5
4
3
2
1
DC IN
ANALOG
WN
DIGITAL
Note: When connecting to a digital recorder
with WORD OUT such as VR800, it always must
be connected to WORD IN of the VC-8 and used
by input of WORD clock.
When connecting a 2 BUS OUT mixer
Connect the mixer BUS OUT to INPUT 1~2 of the VC-8 and select [1-2] of the VC-8 ANALOG INPUT MODE
switch. Signals input to ANALOG IN 1~2 will be assigned, respectively, to ADAT outputs 1~2, 3~4, 5-6 and
7-8. In other words, the ANALOG IN 1~2 signals, in the above combinations, will be simultaneously sent
to each 2 tracks for recording without re-connecting the cable.
8
7
6
5
4
3
2
1
O
IN
AD-12A ONLY
ATA
O
MIDI
WORD OUT SCSI
OPTICAL
I
OUT
IN
AC IN
POWER
OUT
OPTICAL
12V
8
7
6
5
4
3
2
1
DC IN
ANALOG
WOIN
DIGITAL
Note: When connecting to a digital recorder
with WORD OUT such as VR800, it always must
be connected to WORD IN of the VC-8 and used
by input of WORD clock.
7
Model VC-8 Owner’s Manual
Example at operating it as the S/P DIF-ANALOG converter
The following is a connecting example of using the VC-8 as a S/P DIF-ANALOG converter which
makes it possible to extract sound from CD and DVD with the sound card contained in the computer
with S/P DIF digital output. By separating the analog circuit from the computer, this system can
playback (or record) a clear sound free of noise created in the computer.
8
7
6
5
4
3
2
1
IN
OUT
IN
Computer/with
sound card
AD-12A ONLY
OPTICAL
OUT
12V
8
7
6
5
4
3
2
1
DC IN
ANALOG
WORD IN
DIGITAL
VC-8
Monitor amplifier
or recorder
S/P DIF OUT
Setup of the VC-8
Note: Be sure to switch off power to the VC-8 at setup of the various selector switches. Should the switches be
manipulated with power switched on, noise could be created and the VC-8 may not function correctly.
Note: The ANALOG INPUT MODE switch
will not function when the DIGITAL MODE
switch is used for [S/P DIF].
OPTICAL
ADAT/ANALOG CONVERTER
CLOCK
ANALOG INPUT MODE
1-2 1-4 1-8
DIGITAL MODE
ADAT S/P DIF
POWER
STBY ON
75
WORD
OPTICAL INT(44.1k)
ON
OFF
LOCKED
1
2
3
1.Set the DIGITAL MODE switch to [S/P DIF].
3.Switch on power to the VC-8.
2.Set the CLOCK switch to [OPTICAL].
<Other application examples>
When using the Fostex Mode D-160 16 track digital recorder, it can simultaneously record 16 tracks of
analog signals by connecting the VC-8 as shown below.
ADAT
DATA IN 9-16
ANALOG IN 1~8
DATA OUT
VC-8
D-160
ANALOG IN 1~8
ANALOG MIXER
ANALOG MIXER
8
Model VC-8 Owner’s Manual
Specifications
< INPUT x 8 >
• Connector
: RCA pin jack (x 8)
• Input Impedance
• Input Level
: 20k or more
: -10dBV
< OUTPUT x 8 >
• Connector
• Load Impedance
• Output Level
: RCA pin jack (x 8)
: 10k or more
: -10dBV
< DATA IN/OUT >
• Connector
: OPTICAL (x 2)
• Format
: 1. IEC60958 (S/P DIF)
2. Alesis Proprietary Multi Channel Optical Interface
(Switched to 1 or 2.)
< WORD IN >
• Connector
: BNC type (x 1)
• nput Level
: TTL Level
• Input Impedance
: 75 (terminator switched On/OFF)
< OTHERS >
• AD
: 20 bit 64 times over sampling modulation
: 20 bit 128times over sampling modulation
: INT mode : 44.1kHz
• DA
• Sampling Frequency
: OPTICAL/WORD mode : 32 ~ 48kHz
: 0.008%(@ 1kHz, TYPICAL)
: 96dB (TYPICAL)
• Total Harmonic distortion
• Dynamic Range
< GENERAL >
• Dimensions
• Weight
: 220 (W) x 43 (H) x 180 (D) mm
: 1.0kg (Excluding accessories)
• Power Supply
: DC12V, 600mA,Exclusive AC Adaptor (AD-12A)
* Specifications and appearance are subjects to change without notice for product improvement.
* Adat and the
marks are trademarks of Alesis Corporation.
OPTICAL
9
Model VC-8 Owner’s Manual
Declaration of EC Directive
This equipment is compatible with the EMC Directive (89/336/EEC) - Directive on approximation of member
nation's ordinance concerning the electromagnetic compatibility and with the Low Voltage Directive (73/23/
EEC) - Directive on approximation of member nation's ordinance concerning electric equipment designed to be
used within the specified voltage range.
The Affect of Immunity on This Equipment
The affect of the European specification EN50082-1 (coexistence of electromagnetic waves - common immunity specification)
on this equipment are as shown below.
* In the electrical fast transient / burst requirements, radiated electromagnetic field requirements and static electricity discharg-
ing environment, this could be affected by generation of noise in some cases.
FOSTEX DISTRIBUTORS LIST IN EUROPE
* Including non - EU countries. * underlined: contracted distributors (as of November, 1997)
<AUSTRIA>
<ITALY>
NAME: ATEC Audio-u. Videogeraete VertriebsgesmbH.
ADD: Im Winkel 5, A-2325 Velm, Austria
TEL: (+43) 2234-74004, FAX: (+43) 2234-74074
NAME: Recoton Italia Srl.
ADD:V. 1 Maggio, N 18, 40050 Quarto Inferiore, (BO) Italy
TEL: (+39) 51-768576, FAX: (+39) 51-768336
<BELGIUM>
<THE NETHERLANDS>
NAME: EML N. V.
NAME: IEMKE ROOS AUDIO B. V.
ADD: Kuiperbergweg 20, 1101 AG Amsterdam, The Nether-
lands
ADD: Bijvennestraat 1A, B3500 Hasselt, Belgium
TEL: (+32) 11-232355, FAX: (+32) 11-232172
TEL: (+31) 20-697-2121, FAX: (+31) 20-697-4201
<DENMARK>
<NORWAY>
NAME: SC Sound ApS
ADD: Malervej 2, DK-2630 Taastrup, Denmark
TEL: (+45) 4399-8877, FAX: (+45) 4399-8077
NAME: Siv. Ing. Benum A/S
ADD: P. O. Box 145 Vinderen, 0319 Oslo 3, Norway
TEL: (+47) 22-139900, FAX: (+47) 22-148259
<FINLAND>
<PORTUGAL>
NAME: Noretron Audio
ADD: Tonttumuorinkuja 4, FIN-02200 Espoo, Finland
TEL: (+358) 0-5259330, FAX: (+358) 0-52593352
NAME: Caius - Tecnologias Audio e Musica, Lda.
ADD: Rua de Santa Catarina, 131 4000 Porto, Portugal
TEL: (+351) 2-2084456/325400, FAX: (+351) 2-314760
<FRANCE>
<SPAIN>
NAME: Musikengro
ADD: ZAC de Folliouses, B. P. 609, 01706 Les Echets, France
TEL: (+33) 72 26 27 00, FAX: (+33) 72 26 27 01
NAME: Multitracker. S. A.
ADD: C/Garcilaso No. 9, Madrid 28010, Spain
TEL: (+34) 1-4470700, 1-4470898, FAX: (+34) 1-5930716
<GERMANY>
<SWEDEN>
NAME: Studiosound & Music GmbH
ADD: Scheppe Gewissegasse 8, D-35039 Marburg, Germany
TEL: (+49) 6421-12071, FAX: (+49) 6421-15522
NAME: TTS Tal & Ton Studioteknik AB
ADD: Gelbgjutarevagen 4, S-171 48 Solna, Sweden
TEL: (+46) 8-7340750, FAX: (+46) 8-824476
<GREECE>
<SWITZERLAND>
NAME: Bon Studio S. A.
ADD: 6 Zaimi Street, Exarchia, 106.83 Athens, Greece
TEL: (+30) 1-3809605-8, 3302059, FAX: (+30) 1-3845755
NAME: Audio Bauer Pro AG
ADD: Bernerstrasse-Nord 182, CH-8064 Zurich, Switzerland
TEL: (+41) 1-4323230, FAX: (+41) 1-4326558
<ICELAND>
<UK>
NAME: SCV London
NAME: I. D. elrf. electronic Ltd.
ADD: Armula 38 108 Reykjavik, Iceland
TEL: (+354) 588 5010, FAX: (+354) 588 5011
ADD: 3A 6-24 Southgate Road, London N1 3JJ, England, UK
TEL: (+44) 171-923-1892, FAX: (+44) 171-241-3644
10
|