Extron electronic Stereo Receiver MTP 1500RL 15HD A SEQ User Manual

MTP 1500RL 15HD A SEQ • Setup Guide  
This guide provides basic instructions for an experienced installer to set up and operate the Extron MTP 1500RL  
15HD A SEQ twisted pair receiver.  
For full details, see the MTP 1500RL 15HD A SEQ User Guide, available online at www.extron.com.  
RED  
LEVEL  
PEAKING  
SELECT  
GREEN  
BLUE  
DELAY  
MIN/MAX  
ADJUST  
MTP 1500RL Series  
RGB  
INPUT  
MTP  
BUFFERED OUTPUT  
MTP  
OUTPUT  
POWER  
12V  
1.0A MAX  
AUDIO  
R
MONO  
L
ON  
MTP 1500RL 15HD A SEQ  
Installation and Setup  
Step 1 — Mounting  
Turn off or disconnect all equipment power sources. Mount the MTP 1500RL 15HD A SEQ receiver as required.  
Step 2 — Connect Input  
Connect the RJ-45 cable from an MTP transmitter to the Input port on the MTP 1500RL 15HD A SEQ receiver.  
Terminate the cable as shown below right, using the same standard (A or B) at both ends.  
Pin T568A Wire  
Color  
T568B Wire  
Color  
RJ-45 Connector  
1
2
3
4
5
6
7
8
White-green  
Green  
White-orange  
Orange  
Pins:  
12345678  
White-orange  
Blue  
White-green  
Blue  
White-blue  
Orange  
White-blue  
Green  
White-brown  
Brown  
White-brown  
Brown  
Insert Twisted  
Pair Wires  
NOTE:  
The transmitter and receiver are designed for and perform best with Extron Enhanced Skew-Free AV cable terminated in accordance  
with the TIA/EIA T568A standard. CAT 5 cables are acceptable but less preferable. Using preterminated and tested cables is also  
recommend, Cables terminated on site should be tested before use to ensure that they comply with Category 5 specifications.  
Step 3 — Connect Outputs  
Attach the applicable output cables (video, audio, and buffered output).  
A. High resolution video output — Connect a display device to the 15-pin HD connector (RGB).  
B. Audio connector — Connect an audio device to the 5-pole captive screw connector for mono audio output  
Mono output 1+  
Mono output 1-  
Sleeve(s)  
Mono output 2+  
Mono output 2-  
Mono output 1  
NO GROUND.  
Sleeve(s)  
Mono output 2  
NO GROUND.  
Do not tin the wires!  
Balanced Output  
Unbalanced Output  
CAUTION  
For unbalanced audio, connect the sleeve(s) to the ground contact.  
DO NOT connect the sleeves to the negative (-) contacts.  
C. Buffered output — Connect up to 5 daisy-chained MTP receivers to this RJ-45 connector.  
 

Echo Chainsaw CS 400F User Manual
Ei Electronics Smoke Alarm Ei 176 User Manual
Escient MP3 Player DVDM 300 User Manual
Eton Weather Radio FRX2 User Manual
Excalibur electronic Games K452 CS User Manual
Extron electronic Projector SYSTEM 8 10 PLUS User Manual
Garmin Automobile Accessories 190 00307 00 User Manual
Generac Portable Generator 004373 1 004626 0 User Manual
GE Refrigerator 197D3354P013 User Manual
GE Ventilation Hood JN322 JN334 JN335 JN634 JN635 JV322 JV324 JV332 JV334 JV335 JV624 JV634 JV635 User Manual