PMK 560 • Installation Guide
The Extron PMK 560 Pole Mount Kit, designed for use with the Extron PoleVault™ System, allows
for easy mounting of PoleVault products to a projector pole. It is used to mount the PoleVault system switcher the associated
power supply and an accessory device within an enclosure and below a suspended ceiling.
CAUTION: Maximum load for the PMK 560 is 15 lbs (6.8 kg).
Mounting Plate
Base Plate
Items included in the kit are:
Covers (2), Base plate (1), Mounting plate (1),
Tie wraps and pads (to secure power supply)
4-40 Screws (to mount devices) (3),Cover Screws (4)
NOTE: For full device installation, configuration,
menus, connector wiring, and operation details of
the PoleVault switcher, see the PoleVault System
To open, remove 4 cover screws
and slide the covers away.
PMK Covers (2)
Figure 1. PMK 560
Installation
To install the PMK 560 in a PoleVault system:
1. Remove the four cover screws from the center of the PMK 560
(see figure 1). Slide the two halves apart and remove them from
the base plate.
3
NOTE: If the PoleVault switcher and its power supply
4
Attach
Power
Supply
are already installed, go directly to step 4.
Attach PMK to the projector
pole pipe collar with the four
10-32 set screws.
2. To mount the PoleVault switcher, place the mounting plate, with
the raised tabs upwards, on the top surface of the switcher and
pass the two supplied 4-40 x 3/16 inch screws into the top of the
switcher (see figure 2, b). Secure the mounting plate but do not
overtighten.
5
Hook the combined mounting
plate and switcher into the
base plate and secure with
screws.
3. Attach the associated power supply to the base plate with the
supplied tie wraps and pads, by passing them through the
appropriate slots and around the power supply (see figure 2 c).
Tighten until snug.
Projector
Pole
2
Attach Mounting plate
to the top of the
PoleVault switcher.
4. Loosen the four pipe collar set screws (see figure 2 d), and slide
the base plate up the pipe until it is touching the suspended ceiling.
5. Level the base plate and secure it by fully tightening the set screws.
INPUT
P
O
W
1
E
S
2
R
V
3
A
M
A
X
1/
2
SI
G
OUTP
UT
IN
K
3/
4
SI
AUDIO
L
G
L
IN
OU
R
K
T
HDM
PVT
P
I
A
G
IN
SEN IN
G
S
O
R
P
V
S
4
0
5
PVT
IN
INP
L
SA IP
UT
5
R
+V
VOI
AU
X
CELIF
NOTE: At least three set screws must come in contact
T
AMPL
IFIE
D
O
GRO
N
U
D
AUD
L
O
ND
OR
SP
T
SHOR
EAK
T
with the pipe.
IO OU
O
T
U
OVER
E
T
PVS 405D
Switcher
P
R
S
4
/8
T
R
U
Ω
PV
IR
T
REMO
RS-2 TE
32
LAN
S
G
1
Tx
Rx
G
LAN
2
LAN
3
6. Hook the combined plate and switcher into the PMK 560 base plate
(see figure 2, e). Secure it to the base plate with two screws.
ATTENTION:
Use only supplied screws to avoid
Figure 2. Attach the mounting plate to the switcher
damaging the switcher.
and secure both to the base plate.
|