Installation Notes for PMK 450 (70-6ꢀ8-03)
Front Plate (1)
Top Plate (1)
The Extron PMK 450 Projector
Pipe Collar (1) with
Set Screws (4)
Mounting Kit can accommodate
multiple Extron products of one
eighth, quarter, or half rack sizes
with power supplies.
AC Power Cord
Access Slot
The components of the PMK 450
kit are shown in Figure 1. Also
included are:
Plate
Screws (4)
•
•
Set-screw hex wrench (1)
Security Screws (2)
Security screw hex wrench
(1)
Rear Plate (1)
•
•
Velcro™ Pads for securing
power supply (2)
4-40 Screws for mounting
devices (6)
Bottom Plate (1)
Filler Plate (1)
Figure 1 — Contents of PMK 450 kit
Installation
Pipe Collar &
Set Screws
Maximum load for the PMK 450 is 15 lb (6.8 kg).
CAUTION
FRONT
1.
Unscrew the front and rear plates and the security
screws from the sides. Slide the top and bottom
plates apart. The filler plate is attached to the rear
plate and should not be removed.
2.
Ensure that the mounting pipe is installed with
the cable access hole facing the rear, away from the
projector screen.
REAR
3.
4.
Loosen the four pipe collar set screws to allow the
top plate to move freely along the pole.
Extron PMP
Slide the top plate up the pipe until the pipe collar is
positioned just above the cable access hole (Figure 2).
Ensure the rear of the top plate is facing to the rear, in
the same direction as the cable access hole in the pipe.
Figure 2 — Mount top plate on pole
Cable Input from
Sources (AV control)
Bottom Plate
5.
Level the top plate and secure it by fully tightening
the set screws. At least three screws must come in
contact with the pipe.
FRONT
S
s
m
T
U
/8
h
O
P
T
U
O
4
D
IE
IF
L
P
M
A
R
D
N
U
T
L
O
O
R
O
!
T
S
V
G
H
L
T
R
UT
O
C
D
O
U
P
N
O
O
S
R
D
R
E
/
IR
2
K
C
T
EO
T
US
E
A
L
V
1
7T
S
P
2
M
1
ED
3
x
T
D
-2
S
R
R
L
IS
/
VI
IR
IO
TE
U
/M
D
PP
0V
1
U
A
A
R
x
A
T
L
O
S
U
A
V
®
A
B
I
N
G
R
X
/M
X
U
A
U
T
P
U
T
O
E
ID
V
A
3
S
A
2
B
G
R
A
1
EO
ID
V
B
3
I
N
P
U
T
B
6.
Route the cables so that they exit the pipe via the
R
X
E
S
W
O
B
1
P
V
2
A
1
3
M
A
cable access hole (Figure 3).
Cable Access
Hole
7.
Using the supplied 4-40 screws, secure the devices
to the bottom plate. Figure 3 shows the PVS 204
screwed to the plate with a power supply attached by
the supplied Velcro pads.
REAR
Cable Output
to Projector
8.
Attach cables to the device(s) and pull excess cable
back into the ceiling. Feed the output cables to the
projector via the cable access hole and the bottom of
the pipe.
Figure 3 — Route cables
68-1397-01, Rev B
11 07
PMK 450 Projector Mounting Kit • Installation Notes
ꢀ
|