Fisher Price Riding Toy T4262 User Manual

T4262  
Please keep this instruction sheet for future reference,  
as it contains important information.  
Adult supervision is required.  
Never use near steps.  
Choose areas for riding that are free of obstacles.  
Learn to stop safely.  
Use with caution as this product requires skill to operate safely to  
avoid falls, collisions, and injuries to yourself (the rider) and others.  
Maximum weight: 44 lbs. (20 kg).  
For ages between 9 months and 3 years.  
Requires three “AA” batteries (included).  
Adult assembly is required.  
Tool required for assembly: Phillips screwdriver (not included).  
fisher-price.com  
 
Consumer  
Information  
Assembled Parts  
CAUTION  
Base  
This package contains  
small parts in an  
unassembled state. Adult  
assembly is required.  
• Wipe this toy with a clean cloth  
dampened with a mild soap and  
water solution. Do not immerse  
this toy.  
• This toy has no consumer  
serviceable parts.  
• Do not take this toy apart. Do not  
drop this toy on a hard surface.  
• Periodically inspect this product  
for wear or damage. Check all  
nuts and bolts, and tighten as  
needed. Replace worn or broken  
parts immediately.  
2 Rear Wheels  
2 Handles  
2 Front Wheels  
ICES-003  
This Class B digital apparatus  
complies with Canadian ICES-003.  
Operation is subject to the following  
two conditions: (1) this device may  
not cause harmful interference  
and (2) this device must accept  
any interference received,  
Head  
including interference that may  
cause undesired operation.  
NMB-003  
Cet appareil numérique de  
Front Axle  
la classe B est conforme à la  
norme NMB-003 du Canada.  
L’utilisation de ce dispositif est  
autorisée seulement aux conditions  
suivantes: (1) il ne doit pas produire  
de brouillage et (2) l’utilisateur du  
dispositif doit être prêt à accepter  
tout brouillage radioélectrique  
reçu, même si ce brouillage est  
susceptible de compromettre le  
fonctionnement du dispositif.  
#8 x 3/4" (1,9 cm) Screw - 10  
Shown Actual Size  
Tighten and loosen all screws  
with a Phillips screwdriver.  
Do not over-tighten.  
3
 
Assembly  
Rear Wheels  
Base  
1
BOTTOM VIEW  
• Place the base on a flat surface  
so that the bottom faces you.  
• Insert and “snap” the rear wheels  
into the sockets in the base.  
3
• Fit the front wheel assembly to  
the base, as shown.  
Hint: This may require some force.  
• Pull up on the rear wheels to be  
sure each is secure to the base.  
• Insert four screws into the front  
wheel assembly and tighten.  
Front Wheels  
Head  
Front Axle  
4
FRONT VIEW  
Turn the base assembly upright.  
• Fit the head onto the  
base assembly.  
2
• Fit the front wheels to the front  
axle, as shown.  
• Insert a screw into each front  
wheel and tighten.  
4
 
Assembly  
Rewarding Lights  
and Music!  
Screws  
5
Screws  
• Insert two screws into each side  
of the head and tighten.  
• Slide the power/volume switch  
on the back of the dino's head  
to ON with low volume or ON  
Handles  
with high volume  
.
• Press the lights or roll the dino  
along for music and fun sounds!  
• When you are finished playing  
with this toy, slide the power/  
volume switch OFF  
.
• Wipe this toy with a clean cloth  
dampened with a mild soap and  
water solution. Do not immerse  
this toy.  
• This toy has no consumer  
serviceable parts.  
• Do not take this toy apart. Do not  
drop this toy on a hard surface.  
• Periodically inspect this product  
for wear or damage. Check all  
nuts and bolts, and tighten as  
needed. Replace worn or broken  
parts immediately.  
6
BACK VIEW  
• Fit a handle into the socket on  
each side of the head.  
Hint: Turn each handle so that  
each fits into the socket.  
• Push both handles until the  
"snap" together.  
• Pull on each handle to be sure  
they are secure in the sockets.  
5
 
Battery Replacement  
Battery Safety  
Information  
1,5V x 3  
“AA” (LR6)  
In exceptional circumstances,  
batteries may leak fluids that can  
cause a chemical burn injury or  
ruin your product. To avoid  
battery leakage:  
• Do not mix old and new  
batteries or batteries of different  
types: alkaline, standard  
(carbon-zinc) or rechargeable  
(nickel-cadmium).  
• Insert batteries as indicated  
inside the battery compartment.  
• Remove batteries during long  
periods of non-use. Always  
remove exhausted batteries from  
the product. Dispose of batteries  
safely. Do not dispose of this  
product in a fire. The batteries  
inside may explode or leak.  
• Never short-circuit the  
battery terminals.  
• Use only batteries of the same or  
equivalent type as recommended.  
• Do not charge non-  
rechargeable batteries.  
• Remove rechargeable batteries  
from the product before charging.  
For best performance, we  
recommend replacing the  
batteries that came with three  
"AA" (LR6) alkaline batteries.  
• Locate the battery compartment  
on the side of the dino.  
• Loosen the screws in the battery  
compartment door. Remove  
the battery compartment door.  
Remove the exhausted batteries  
and dispose of them properly.  
• Insert three, new "AA" (LR6)  
alkaline batteries.  
• Replace the battery compartment  
door and tighten the screws.  
• If this toy begins to operate  
erratically, you may need to reset  
the electronics. Slide the power/  
volume switch off and then  
back on.  
• When lights or sounds from  
this toy become faint or stop,  
it’s time for an adult to change  
the batteries!  
• If removable, rechargeable  
batteries are used, they are  
only to be charged under  
adult supervision.  
• Protect the environment  
by not disposing of this  
product with household  
waste (2002/96/EC).  
Check your local authority  
for recycling advice  
and facilities.  
6
 
Walker  
To change to Walker mode, follow these steps:  
Latch  
Press  
1
2
Slide  
1
2
Bottom View  
• Spread the seat halves until they  
“click” in place. Turn the toy  
over. It is now ready to be used  
as a walker.  
Turn the toy over. Press and slide  
the latch to an open position,  
as shown.  
7
 
Ride-On  
To change to Ride-On mode, follow these steps:  
Press  
Latch  
1
2
Top View  
Bottom View  
• While pressing the seat button,  
close the seat halves. Turn  
the toy over.  
• Slide the latch to a closed  
position. It should “click” into  
place.Turn the toy over. It is now  
ready to be used as a ride-on.  
8
 

Compaq Personal Computer Internet PC User Manual
Coway Water System P 07CL User Manual
Cuisinart Popcorn Poppers CPM 900BKA User Manual
Cypress Computer Hardware CY2048WAF User Manual
Dynamic Distributors Stud Sensor 103B11 User Manual
Electro Voice Microphone PL37 User Manual
Electro Voice Portable Speaker FR12 2 User Manual
Fisher Price High Chair P9043 User Manual
Garland Oven SUMG100D1 User Manual
Global Machinery Company Portable Generator LS LINE REDEYE User Manual