Fellowes Paper Shredder CC4 2 User Manual

PAPER SHREDDER  
Personal Series  
MODELS  
CC4-2  
PRODUCT USAGE GUIDE  
CC4-2  
Sheet capacity*:  
Shred type:  
5
Confetti  
Shred size:  
5/32" x 2"  
Entry width:  
9-1/2"  
Recommended use:  
Maximum running time:  
10-20 shredding passes per day  
5-7 min. on/15 minutes off  
*Sheet capacity measured with 20 lb., 8-1/2" x 11" paper with the shredder operating at rated voltage.  
Different paper weights, humidity, and electrical currents will affect capacity.  
PLEASE READ AND SAVE THIS MANUAL WITH YOUR ORIGINAL RECEIPT  
Customer Service: 1-800-955-0959  
 
Cool-Down Cycle  
OPERATION  
This shredder is protected with a special safety feature  
which prevents the motor from overheating with exten-  
sive use. When shredding is attempted beyond the  
machine's maximum running time, the shredder  
will automatically shut off its motor until it has  
cooled to an acceptable operating level. This is nor-  
mal and the shredder will return to operation after the  
cool-down or "off" period. See "Product Usage Guide"  
on front panel for maximum running time and related  
cooling "off" time.  
This product features an auto-start  
sensor. This sensor will turn on the cut-  
ting blades whenever anything is inserted into the  
paper entry (while the power switch is in the AUTO  
position). For the safety of pets and children, we rec-  
ommend always moving the power switch to OFF and  
unplugging whenever the shredder is unattended or  
not in use.  
1. Assemble shredder (see "ASSEMBLY").  
2. Remove any paper clips or other foreign objects  
(except staples) from paper. If folding paper to fit  
paper entry, adjust sheet capacity appropriately.  
Clearing a Jam  
If the shredder sheet capacity is exceeded or paper is  
not put in straight, a jam may result. See "Product  
Usage Guide" on front panel for maximum sheet  
capacity for your shredder.  
Do not attempt to shred paper clips or  
other hard materials (except staples)  
To clear a jam:  
with this machine. Extensive use of paper clips or other  
hard materials will result in damage to the cutting sys-  
tem and will void the manufacturer's warranty.  
3. Be sure power switch is in OFF (O) position. Plug  
shredder into proper power supply outlet.  
1. Move the power switch to the REVERSE (R) posi-  
tion. (NOTE: If waste basket is full, empty it before  
clearing jam.) The shredder will reverse the paper  
to clear the jam.  
4. Move power switch to AUTO (I) position. To clear  
the cutting blades, the shredder will "run" for about  
1 second immediately after switching to AUTO (I).  
When the unit is turned on and in standby mode,  
the shredder is ready to be fed paper through the  
paper entry. (See "TROUBLESHOOTING" if red  
LED is lit.)  
2. If the shredder jams in reverse, move the power  
switch to AUTO (I) and allow to run for about five  
seconds. If jam does not clear, move power switch  
to REVERSE (R) again and allow to run for about  
five seconds. Repeat this procedure until the jam is  
cleared. If necessary, use care to grasp the paper  
carefully and pull out to clear the jam.  
3. Once the jam is cleared, move the power switch to  
AUTO (I) for continued shredding or OFF (O) if  
shredding is complete.  
NEVER insert hands or fingers into  
paper entry as serious personal injury  
may result.  
Do not exceed recommended sheet  
capacity (see "Product Usage Guide"  
on front cover of this manual).  
5. Slide paper straight into paper entry until the shred-  
der automatically begins shredding.  
MAINTENANCE  
Confetti cut shredders require regular (monthly) oiling of  
the cutting blades to maintain proper operation. Failure to  
oil the blades regularly could result in reduced sheet  
capacity performance, excessive noise during operation,  
paper jams and possibly shredder failure.  
The shredder automatically stops a few seconds  
after shredding is complete.  
Continue shredding as desired to a MAXIMUM  
shredding time of 5-7 minutes. At this time, the  
machine MUST be allowed to "cool down" for a  
MINIMUM of 15 minutes. (See "Cool-Down  
Cycle" for more information.)  
If the shredder jams or shuts off before the maxi-  
mum shredding time, see "Clearing a Jam" section  
for further instructions.  
We recommend using only Powershred Lubricant  
#35250 (available by contacting Fellowes) or a veg-  
etable-based oil (such as corn or canola) in a non-  
aerosol container with an extension nozzle.  
Never use flammable synthetic oil,  
petroleum- based, or aerosol lubri-  
cants to oil the cutting blades. Some agents may com-  
bust, causing serious injury.  
To oil the cutting blades:  
1. From the top of the shredder, squeeze the recom-  
mended lubricant across the full width of the  
blades.  
2. Move the power switch to AUTO (I) position and  
allow the blades to run at least 3 seconds.  
3. Move the power switch to REVERSE (R) position  
and allow it to run for at least 3 seconds.  
4. Repeat steps 2-3 above at least 3 times.  
6. Move power switch to OFF (O) position when  
shredding is complete.  
7. Unplug power cord from outlet whenever shredder  
is unattended or not in use.  
8. Check basket to see if it is full. If full, remove shred-  
der head and empty basket contents. Replace  
shredder head onto basket.  
 
TROUBLESHOOTING  
LIMITED WARRANTY  
Shredder will not  
Fellowes warrants all the cutting cylinders of the  
machine to be free of defects in material and  
workmanship for 3 years from the date of  
purchase by the original consumer. Fellowes  
warrants all other parts of the machine to be free  
of defects in material and workmanship for 1 year  
from the date of purchase by the original con-  
sumer. If any part is found to be defective during  
the warrant period, your sole and exclusive  
remedy will be repair or replacement, at FellowesÕ  
option and expense, of the defective part.  
This warranty does not apply in cases of abuse,  
mishandling or unauthorized repair. ANY  
IMPLIED WARRANTY, INCLUDING THAT OF  
MERCHANTABILITY OR FITNESS FOR A  
PARTICULAR PURPOSE, IS HEREBY LIMITED  
IN DURATION TO THE APPROPRIATE  
WARRANTY PERIOD SET FORTH ABOVE.  
In no event shall Fellowes be liable for any  
consequential or incidental damages attributable  
to this product. This warranty gives you specific  
legal rights. You may have other legal rights that  
vary from state to state.  
For more detail or to obtain service under this  
warranty, please contact Fellowes Customer  
Service at 1-800-955-0959, Monday through  
Friday, 8 AM - 5 PM (Central Standard Time).  
For specific instructions on obtaining service  
under this warranty on machines purchased out-  
side the USA, contact the appropriate location  
listed in the Contact for Service section of this  
instruction manual.  
a. Shredder is not plugged in.  
operate.  
b. Power switch is in the OFF (O)  
position. Move switch to AUTO (I)  
position.  
c. Shredder is jammed. See  
"Clearing a Jam" section.  
d. Shredder has exceeded the maxi-  
mum run time and requires a  
"cool-down" time. See "Product  
Usage Guide" on front panel.  
e. Shredder is not assembled prop-  
erly. See "Assembly."  
Shredder makes a  
loud squeaking or  
rubbing noise.  
a. Cutting blades need to be oiled  
REGULARLY. See "MAINTE-  
NANCE" section.  
Shredder suddenly  
stops while  
shredding.  
a. Shredder has exceeded the maxi-  
mum run time and requires a  
"cool-down" time. See "Product  
Usage Guide" on front panel.  
b. Shredder is jammed. See  
"OPERATION - Clearing a Jam."  
Shredder shreds  
less than capacity.  
a. Cutting blades need to be oiled  
REGULARLY. See "MAINTE-  
NANCE" section.  
a. Shredder is not assembled prop-  
erly. See "ASSEMBLY."  
Red LED is lit.  
Shredder operates  
only in REVERSE.  
a. A small piece of paper may be  
blocking the auto-start sensor of  
this shredder. Move the power  
switch to the OFF (O) position and  
unplug the shredder. Turn shred-  
der over and use a toothpick  
(from the underside of the unit)  
to clear the paper blockage at the  
auto-start sensor (center) location.  
Shredder runs con-  
tinuously when in  
AUTO.  
a. A small piece of paper may be  
causing the auto-start feature to  
run continuously. Move the power  
switch to the OFF (O) position and  
unplug the shredder. Use a  
toothpick (from the top of the  
unit) to clear the paper blockage  
at the auto-start sensor (center)  
location.  
Warrantor: Fellowes Manufacturing Company.  
a. This is normal. The shredder runs  
a few seconds longer than the  
paper in order to keep the cutters  
clear of paper particles and reduce  
the chances of a jam.  
Shredder runs for a  
few seconds after  
the paper has  
Customer Service 1-800-955-0959  
cleared the cutters.  
1789 Norwood Avenue ¥ Itasca, Illinois 60143-1095  
630-893-1600  
®
Australia  
Benelux  
Canada  
France  
Germany  
Italy  
Japan  
Poland  
United Kingdom  
Tullamarine, Vic Vianen, NL  
Markham, Ont.  
Rennes, I-V  
Garbsen, Han.  
Camerano, AN  
Tokyo  
Warsaw  
Doncaster, S. Yorks.  
© 2001 Fellowes Printed in China. Form No. 30117  
 

Cooper Lighting Landscape Lighting UTR50SR2554 User Manual
Craftsman Blower 358794941 User Manual
Creative Modem DI5732 User Manual
Dell Scanner JSM 6060LV User Manual
Eclipse Fujitsu Ten Car Stereo System CD7000 User Manual
Electro Voice Portable Speaker MTL 4B User Manual
Fortinet Network Card FortiGate 800 User Manual
GE Monogram Planer ZGG36N30YSS User Manual
Generac Power Systems Portable Generator GP6500 User Manual
Genie Air Conditioner AG_05 User Manual