Dixon Lawn Mower ZTR 308 311 User Manual

TECHNICAL DATA BROCHURE  
IMPORTANT - READ OPERATOR'S MANUAL BEFORE OPERATION.  
Seat Adjustment  
Loosen Bolts on sliding brackets under each side of seat, slide seat forward or rearward to  
desired position. Re-tighten bolts. Do not operate mower with bracket bolts in a loose  
condition.  
Mower Blade Operation  
To start mower blades, move lever on floor slowly to "ENGAGE" position. To stop  
mower blades, move lever on floor slowly to "DISENGAGE" position.  
Body Removal  
1. Disconnect throttle cable from engine.  
2. Disconnect the rear wiring loom (P/N 4109) from the body by lightly squeezing the Econo-  
Seal plug. This is located at the left rear of the body.  
3. Note: Loosen bolts that hold body switch (P/N 4079) and slide switch away from engaging  
rod. Tighten one bolt just enough to hold switch in this position until body is  
reassembled.  
4. Remove 4 control lever bolts and remove upper control levers (P/N 1501L-1501R).  
5. Remove engaging handle (P/N 6089) by removing bolt and nut under handle.  
6. Remove the 2 attach nuts on floor of body and 2 sheet metal screws at the rear of body.  
7. Place height adjustment lever in vertical position, engage parking brake and carefully lift  
body up and off chassis.  
8. Reverse the above procedure for assembly.  
Safety Checks  
With the mower deck in the engaged position slide the body switch (P/N 4079) toward  
the engaging rod (P/N 6087-1) until the switch leaf just makes contact with the  
switch button. Tighten both bolts in switch bracket.  
With mower deck engaged, attempt to start engine in all cutting height positions.  
If engine starts in any cutting height position, re -adjust the switch. Disengage  
the mower deck and start the engine in each cutting height position. If engine  
fails to start in any cutting height position, re-adjust switch.  
With operator in normal mowing/position, engage mower deck and remove weight from  
seat. The engine should stop. Repeat this procedure in each cutting height  
position. If engine does not stop when operator rises from seat in each cutting  
height position, return to an authorized Dixon dealer for adjustment f>r repairs.  
Parking Brake Adjustment  
Remove body as described above. Tighten nut on brake rod (P/N2533) (Located in front of the  
transaxle on each side.), just enough to prevent brake from slipping when engaged. CAUTION:  
Over tightening may cause premature wear on brake band (P/N 5085).  
Mower Drive Belt Adjustment  
Belt tension for mower drive belt (P/N 2412) is adjusted by loosening nut on the connecting  
arm assembly (P/N 2171 -A ) and turning bolt to achieve desired tension. Re-tighten nut.  
Tension should be checked with belt in engaged position.  
Removing Mower Deck  
1.  
Remove engaging handle (P/N 6089) by removing bolt and nut under handle.  
2. Loosen belt keeper (P/N 2234) located under engine by loosening 2 rear engine  
mount bolts to allow mower deck drive belt to come free of rear pulley.  
Re-tighten belt keeper,  
(continued on back)  
1
DIXON INDUSTRIES, INC. B OX 484, COFFEYVILLE, KANSAS 67337 (316) 251-2000  
D.I. Form S-35 (Rev. 6/83)  
 
3
 
4
 
PART # NAME  
ART # NAME  
PART # NAME  
1015  
1020  
1022  
Caster Weldment  
2444  
2449  
2452  
2456  
2460  
2463  
2465  
2466  
2468  
2469  
2470  
2501  
2504  
2507  
2508  
2509  
2514  
2515  
2524  
Battery Ground Cable  
4122  
4124  
4148  
5005  
5007  
Body Wiring Loom  
Caster Axle  
Caster Nipple  
Solenoid  
Seat Angle  
Discup  
Caster Wheel & T1re  
Engaging Idler Bshg.  
Model Decal-ZTR 308  
Parking Brake Decal  
Seat  
1022A Caster Wheel Bearing  
I030  
I039  
1108  
1109  
Upper Lift Link-Rear  
Lower Lift Link  
Cone Frame  
5009R Cradle  
Tire - Front Wheel  
Inner Tube - Front Wheel  
Rear Tire(16x6.5-8)  
Rear Rim (16x6.5-8)  
Double Engine Pulley  
V-Belt  
5009L  
5012  
5013  
5015  
5016  
5018  
5019  
5021  
Cradle  
Cradle Shaft  
1501R Upper Control Lever  
ISOIL Upper Control Lever  
Cone Frame Shaft  
24T Sprocket  
1507  
1536  
1540  
543  
Wheel/Deck Hub Bearing  
Chain Connecting Link  
Engine Shaft Key  
Lift Knob  
Transaxle Pulley  
Rear Tube' Weldment  
Front Tube  
Molded Cone  
9T Sprocket-Narrow  
Transaxle Chain  
9T Sprocket-Wide  
Support L  
544  
Bellcrank  
Support R  
5024-1 Cradle Spring  
560-1 Battery Splash Guard  
Support Shaft  
5028  
5036  
5046  
5047  
5053  
6059  
6089  
6107  
Transaxle Bearing  
Pivot Spring  
574  
606  
647  
654  
655  
657  
Brake Pivot Weldment  
Brake Mount Weldment  
Control Pin  
Torque Rod Stiffener R  
Torque Rod Stiffener L  
Transaxle  
Positive Neutral R  
Positive Neutral S  
Brake Arm Retainer  
Flat Idler Pulley  
Engaging Handle  
Deck Pin  
Transaxle Idler Weld.  
Transaxle Idler Pulley  
Transaxle Idler Spring  
2600-3 Mower Deck Assy.  
2601-2 Mower Deck Weldment  
2612  
Engaging Idler Weld.  
2000-2 Frame Weldment  
2620-1 Engaging Rod  
2077  
2100  
2105  
2154  
2155  
2159  
2164  
Walking Beam Weldment  
2626  
2640  
2641  
2642  
2645  
2647  
2648  
2668  
2823  
3029  
3120  
3123  
3129  
3502  
3504  
3507  
3508  
3511  
3521  
3531  
3532  
3533  
3536  
Deflector Sheet  
6136-2 Engaging Cam Weld.  
Bumper Weldment  
Mower Deck Hub Assy.  
Mower Deck Hub Sub-Assy.  
Mower Deck Hub  
6159  
Stabilizer Arm Wel  
Bumper Pad  
Hub Pulley Spacer  
Hub Bearing Spacer  
Engaging Idler Spacer  
Support Sprocket Spacer  
Blade Shaft Weldment  
Blade Washer  
Deck Hub Key  
2165-1 Torque Rod  
Stiffener  
2166  
Pivot Bolt  
Oil Drain Assy.  
2171A Connecting Arm Assy.  
Front Grommet  
2171-1 Connecting Arm Weldment  
Nylon Shoulder Bshg.  
Control Pin  
2172  
2176  
2179  
2180  
2204  
Swivel Fitting  
Body  
Plastic Tube Closure  
Hand Grip  
Switch Bracket-Body  
Switch Bracket-Sw. Sect.  
Wheel Hub  
Double Ball Joint  
Floor Pad -Long  
2214R Brake Arm Weldment R  
2214L Brake Arm Weldment L  
Floor Pad -Short  
Adhesive Bumper Pad  
Engaging Cam Mount Bshg.  
Decal-Operating Inst.  
Decal-Blade Drive  
Decal-Cutting Height  
Warning Label-Danger  
2221  
Transaxle Shim 16ga  
2222  
Transaxle Shim 22ga  
2225  
Battery Box Weldment  
2231 Lower Control Lever Assy  
2234 Belt Keeper  
4005B Throttle Cable  
2237 Tie Bar Assy.  
4006-2 Solenoid-Starter Cable  
4006-8 Solenoid-Battery Cable  
4007-1 Battery-12V  
2238 Tie Bar  
2240 Short Brake Rod Assy.  
2402 Rear Wheel & Tire  
4009  
4013  
4047  
4067  
Wire Clip(not shown)  
Wire Tie (not shown)  
Seat Switch  
406  
408  
411  
412  
413  
414  
417  
30" Mower Blade  
Drive Chain Assy.  
Mower Deck V-Pulley  
Deck Drive Belt  
Ignition Switch  
V-Idler Pulley  
4067A Switch Key (for 4067)  
Engaging Idler Tension Sprg  
Control Rod Assy  
4075  
4079  
4092  
4109  
10 AMP Fuse  
Body Switch  
418 Long Brake Rod Assy  
422 Name Decal  
436 Switch Decal  
Fuse Holder  
Rear Wiring Loom  
4115  
Wiring Kit  
 

Clover Electronics Digital Camera CC5301 User Manual
Conair Styling Iron CS41CS User Manual
Contec Universal Remote RT U61C User Manual
Cooper Lighting Work Light UN Series User Manual
Craftsman Computer Accessories LAP30ULV CT User Manual
Danby Dishwasher DDW1809W 1 User Manual
Dell Server E05S User Manual
DigiTech Music Pedal RP50 User Manual
Excalibur electronic Paper Shredder PS116 User Manual
Gitzo Musical Instrument G7680 User Manual