DigiTech Guitar SC 2 User Manual

 
WARRANTY:  
We at DigiTech are proud of our products and back-up each one with the following warranty:  
The warranty registration card must be mailed within ten days after purchase date to validate this warranty.  
DigiTech warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship  
under normal use and service.  
DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect,  
provided the product is returned to DigiTechWITH RETURN AUTHORIZATION, where all parts and labor will be  
covered up to a period of one year (this warranty is extended to a period of six years when the product has been properly  
registered by mail or through our website). A Return Authorization number may be obtained from DigiTech by telephone.  
The company shall not be liable for any consequential damage as a result of the product's use in any circuit or assembly.  
Proof-of-purchase is considered to be the burden of the consumer.  
DigiTech reserves the right to make changes in design, or make additions to, or improvements upon this product without  
incurring any obligation to install the same on products previously manufactured.  
The consumer forfeits the benefits of this warranty if the product's main assembly is opened and tampered with by anyone  
other than a certified DigiTech technician or, if the product is used with voltages outside of the range suggested by the  
manufacturer.  
The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any  
person to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its  
dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes  
beyond their control.  
NOTE:The information contained in this manual is subject to change at any time without notification. Some information  
contained in this manual may also be inaccurate due to undocumented changes in the product or operating system since  
this version of the manual was completed.The information contained in this version of the owner's manual supersedes all  
previous versions.  
 
 
Introduction  
More than a remarkable achievement, HardWirerepresents a collection of  
significant improvements in effects pedals for guitar. HardWire pedals pro-  
vide a suite of well-known effects, each with superior tone and control. But  
these pedals go above and beyond their peers to provide such distinguishing  
features as true bypass and high voltage operation, making them essential  
additions to the signal chain of players who know about sound quality and  
demand the utmost in performance.  
Included Items  
HardWire SC-2Valve Distortion  
HardWire StompLock™  
Foot Switch Glow Sticker  
Hook-and-loop Pedalboard Pad  
Warranty card  
 
1 2 3  
4
5
6
7
11  
8
8
9
10  
2
 
What Does This Do?  
1. Level Knob - Controls the distortion output level. Turn the knob  
clockwise to increase and counter-clockwise to decrease the output  
level.  
2. DC Adapter Jack - Connect (an optional) Harman PS200R  
power supply to this jack. Use the proper supply for your area’s  
mains line voltage.  
3. Low Knob - Controls the level of low frequency (bass) boost/cut.  
Turn the knob clockwise to increase and counter-clockwise to  
decrease the bass level.  
4. High Knob - Controls the level of high frequency (treble) boost/  
cut.Turn this knob clockwise to increase and counter-clockwise to  
decrease the treble level.  
5. Gain Knob - Controls the overall distortion gain. Turn the knob  
clockwise to increase and counter-clockwise to decrease the  
amount of distortion gain.  
 
6. Voicing Switch -This switches between the Distortion’s two  
voicings. Crunch provides a classic balanced distortion. Saturated  
features an extra gain stage for maximum sustain distortion making  
it ideal for solos.  
7. Input - Connect your instrument or the output of another pedal  
to this jack.This jack enables battery power to the pedal when con-  
nected.To prolong battery life, disconnect the cable from the Input  
jack when not in use. If the optional Harman PS200R power supply  
is used, cables can remain connected.  
8. Foot Switch Release Pins -These two pins are spring loaded  
hinges that hold the Foot Switch in place. See page 7 for informa-  
tion on accessing and changing the battery.  
9. Indicator LED - Lights when the effect is turned on.When bat-  
tery power is low (approximately ꢀ5 minutes before it dies), the  
Indicator LED begins to dim giving you advanced warning that very  
shortly you will need to replace the battery.  
 
10. Foot Switch -Turns the effect on and off.  
11. Output - Connect this output to the input of your amplifier or the  
input of another pedal.  
Note: Use unbalanced mono instrument cables only.  
5
 
Amplifier Setup  
PS200R  
(optional)  
or  
 
Battery Operation  
In the event that battery power is completely depleted, HardWire pedals  
automatically switch into bypass.This eliminates the need to remove the  
pedal from your pedal chain if the battery is dead. To replace the battery, do  
the following:  
ꢀ. Using the tip of a ꢀ/ꢂ” guitar cable, push in one of the Release Pins in on  
either side of the Foot Switch, and remove it from the pedal chassis.  
2. Remove the battery from the battery compartment and disconnect the  
battery cable.  
ꢁ. Connect a new battery to the battery cable and put it back in the bat-  
tery compartment. Make sure the battery cable does not interfere with  
the spring or pedal switch arm.  
ꢂ. Place one hole of the Foot Switch over its corresponding pin.  
5. Push the opposite pin in and lower the other side of the Foot Switch  
into place over the depressed pin. Release the pin.When the Foot  
7
 
Switch is properly fastened, both Release Pins are flush with the outer  
side of the pedal.  
Foot Switch  
Pedal Switch  
Arm  
9VDC Battery  
Foot Switch  
Release Pin  
Battery  
Compartment  
Foot Switch  
Release Pin  
Spring  
Pedal Chassis  
 
HardWire Performance Accessories  
The performance accessories make integrating a HardWire pedal into any  
pedal board a snap.The following accessories are included:  
Hook-and-loop Pedalboard Pad (designed to attach to the surfaces  
found on most commercial pedalboards)  
Foot Switch Glow Sticker (easily visible on dark stages)  
StompLock(keeps your settings where you want them)  
 
Hook-and-loop Pedalboard Pad  
To attach the Pedalboard Pad, do the following:  
ꢀ. Peel off the existing rubber skid pad from the bottom of the pedal.  
2. Peel the adhesive protector from the back of the Pedalboard Pad.  
ꢁ. Apply the Pedalboard Pad to the bottom of the pedal.  
ꢀ0  
 
Foot Switch Glow Sticker  
To attach the Foot Switch Glow Sticker, do the following:  
ꢀ. Peel the adhesive backing from the Foot Switch Glow Sticker.  
2. Apply the Glow Sticker to the top of the Foot Switch.  
ꢀꢀ  
 
StompLock  
To place the StompLock over the pedal knobs, do the following:  
ꢀ. Set the knobs to your preferred setting.  
2. Gently push the StompLock over the top of the knobs.  
ꢁ. To remove the StompLock, gently lift one side and then the other.  
ꢀ2  
 
Specifications  
Controls - Level, Low, High, Gain,Voice Switch, On/Off Pedal  
Jacks - Input, Output  
Input Impedance - >500 kΩ - effect on  
Output Impedance - ꢀ kΩ - effect on  
Input Impedance - true hardwire bypass - effect off  
Output Impedance - true hardwire bypass - effect off  
Power Supply - ꢅV Alkaline Dry Battery or  
Harman PS200R ꢅV DC power supply  
Current Draw - 20 mA (typical at ꢅV DC)  
Power Consumption - ꢀꢄ0 mW (typical w/optional PS200R power supply)  
Dimensions - 5.25”(L) x ꢁ.5”(W) x 2.ꢀ5”(H)  
Weight - ꢀ.ꢁ lbs.  
Optional Power Supply:  
PS200R-ꢀ00 (ꢀ00V~ 50/ꢃ0Hz)  
PS200R-ꢀ20 (ꢀ20V~ ꢃ0Hz)  
PS200R-2ꢁ0 (2ꢁ0V~ 50Hz)  
PS200R-2ꢂ0 (2ꢂ0V~ 50Hz)  
ꢀꢁ  
 
 
 
8760 South Sandy Parkway  
Sandy, Utah 84070  
PH (801) 566-8800  
FAX (801) 566-7005  
HardWire and DigiTech are trademarks  
of the Harman Music Group Inc.  
Copyright - Harman Music Group  
Manufactured in the USA  
HardWire SC-2  
Owners Manual 18-0666-A  
Please visit us  
on the World Wide Web at:  
 

Clarion CD Player DXZ835MP User Manual
Craftsman Lawn Mower 900370520 User Manual
Craftsman Trimmer 31679249 User Manual
Crate Amplifiers Stereo Amplifier GT 80DSP User Manual
Cuisinart Mixer HM 70 User Manual
Digimate Flat Panel Television DGL2700 User Manual
Digital Dream Digital Camera sportsman User Manual
EVGA Computer Hardware 123 CD E635 KR User Manual
Extron electronic Network Card MR D Series User Manual
Flymo Chainsaw HT 5 50 User Manual