Creda Oven Single Oven User Manual

Single Ovens  
Users Instruction & Installation Book  
Note: Timer must be set to ‘Time of Day’ and ‘Manual’  
before the oven(s) can be used.  
Note: Ensure that the oven is securely fixed to the  
cabinet before use.  
This appliance shall be installed in accordance with the  
regulations in force and only used in a well ventilated space.  
Read the instructions before installing or using the  
appliance and retain them for future use  
 
CONTENTS  
Introduction  
4
5
For Your Safety – Always  
For Your Safety – Never  
Features  
6
7
Controls  
8
Oven Timer Operation  
Know Your Timer  
9
10  
11-14  
15  
16  
Electronic Clock & Automatic Timer Operation  
Grill Pan and Handle  
Using The Grill  
Using the Oven  
Care and Cleaning  
Installation  
17  
22  
25  
Something Wrong?  
Service  
33  
Back Cover  
DISPOSAL OF YOUR PRODUCT  
To minimise the risk of injury to children please dispose of your product carefully and  
safely. Remove all doors and lids. Remove the mains cable (where fitted) by cutting off  
flush with the appliance and always ensure that no plug is left in a condition where it  
could be connected to the electricity supply.  
To help the environment, Local Authority instructions should be followed for the disposal  
of your product.  
3
 
INTRODUCTION  
Your new cooker is guaranteed* and will give lasting service. This guarantee is only  
applicable if the appliance has been installed in accordance with the installation  
instructions detailed in this booklet.  
To help make best use of your cooking equipment,  
please read this booklet carefully.  
The cooker is designed specifically for domestic use and responsibility will not be accepted  
for use in any other installation.  
When first using the cooker ensure that the room is well ventilated (e.g. open a window or  
use an extractor fan) and that persons who may be sensitive to the odour avoid any fumes.  
It is suggested that any pets be removed from the room until the smell has ceased. This  
odour is due to any temporary finish and also any moisture absorbed by the insulation.  
* The guarantee is subject to the provisions that the appliance:  
(a) Has been used solely in accordance with the Users Instruction Book.  
(b) Has been properly connected to a suitable supply voltage and gas supply as  
stated on the Data badge attached to the equipment.  
(c) Has not been subjected to misuse or accident or has not been modified or  
repaired by any person other than the authorised employee or agent.  
(d) Has been correctly installed.  
This appliance conforms to the following EEC Directives:  
Low Voltage Equipment  
73/23/EEC  
93/68/EEC  
Gas Appliances  
90/396/EEC  
Electromagnetic Compatibility  
89/336/EEC  
92/31/EEC  
93/68/EEC  
4
 
FOR YOUR SAFETY  
When used properly, your appliance is completely safe but as with any product  
there are certain precautions that must be observed.  
PLEASE READ THE PRECAUTIONS BELOW BEFORE USING YOUR  
APPLIANCE.  
ALWAYS  
Always make sure you remove all packaging and literature from inside the oven  
and grill compartments before switching on for the first time.  
Always make sure you understand the controls prior to using the appliance.  
Always keep children away from the appliance when in use as the surfaces will  
get extremely hot during and after cooking.  
G
G
G
Always make sure all controls are turned off when you have finished cooking  
and when not in use.  
Always stand back when opening an oven door to allow any build up of steam or  
heat to disperse.  
Always use dry, good quality oven gloves when removing items from the  
oven/grill.  
G
G
G
Always take care to avoid heat/steam burns when operating the controls.  
Always turn off the electricity supply at the wall switch before cleaning and  
allow the appliance to cool.  
G
G
Always make sure the shelves are in the correct position before switching on  
the oven.  
G
Always keep the oven and grill doors closed when the appliance is not in use.  
Always keep the appliance clean as a build up of grease or fat from cooking can  
cause a fire.  
G
G
Always follow the basic principles of food handling and hygiene to prevent  
the possibility of bacterial growth.  
G
Always keep ventilation slots clear of obstructions.  
Always refer servicing to a CORGI registered service engineer.  
G
G
5
 
FOR YOUR SAFETY  
NEVER  
Never leave children unsupervised where a cooking appliance is installed as all  
G
cooking surfaces will be hot during and after use.  
Never allow anyone to sit or stand on any part of the appliance.  
Never store items above the appliance that children may attempt to reach.  
Never remove the oven shelves whilst the oven is hot.  
Never heat up unopened food containers as pressure can build up causing the  
container to burst.  
G
G
G
G
Never store chemicals, food stuffs or pressurised containers in or on the  
appliance, or in cabinets immediately above or next to the appliance.  
Never use the appliance as a room heater.  
Never use the grill to warm plates.  
Never dry any items on the oven doors.  
G
G
G
G
G
Never allow children to play with the controls.  
NOTE: The use of a gas cooking appliance results in the production of heat and moisture  
in the room in which it is installed. Ensure that the kitchen is well ventilated; keep  
natural ventilation holes open or install a mechanical ventilation device (mechanical  
extractor hood).  
Prolonged intensive use of the appliance may call for additional ventilation, for example  
opening of a window, or more effective ventilation, for example increasing the level of  
mechanical ventilation where present.  
6
 
FEATURES  
24 Hour Digital  
Electronic Clock  
and Oven Timer  
Oven  
Temperature  
Control  
Grill  
Control  
❍ ❍  
Oven  
Door  
7
 
CONTROLS  
TIMER  
OVEN TEMPERATURE CONTROL  
A
B
GRILL CONTROL  
CONTROL MARKINGS  
Control  
Knob  
Description  
Function  
Push in and turn the control knob fully  
anti-clockwise, wait for the oven burner to ignite,  
and then turn to the required gas mark number.  
Note: The oven burner will only operate when the  
door is closed.  
Oven Temperature Control  
A
Push in and turn the control knob anti- clockwise to  
the large flame symbol, wait for the burner to ignite,  
and then turn to the required setting.  
Note: The grill burner will only operate when the  
door is open.  
B
Grill Control  
Cooling Fan:  
A gentle flow of air will be blown below the control panel when any  
control is used.  
Note: Whenever the appliance has been used, the cooling fan may  
continue to run or restart itself after all the controls have been turned  
off. This indicates that the appliance is still warm.  
Oven Interior  
Light  
The oven light is operated when the oven control is used.  
“Slow Cook”  
Setting  
The main oven has an “Slow Cook” setting. This can be used for slow  
cooking, keeping food warm and warming plates for a short period.  
Note: It is advisable to check that all oven controls have been switched off when you  
have finished using the appliance.  
8
 
OVEN TIMER OPERATION  
Note: Timer must be set to ‘Time of Day’ and ‘Manual’ before the ovens can be  
used.  
AUTOMATIC COOKING  
The oven can be controlled by the automatic timer.  
HINTS ON AUTOMATIC COOKING  
1. Select foods which will require the same cooking time and temperature.  
2. To ensure food does not cool down and require reheating, set the end time so the  
food is ready when you require it.  
3. Always ensure that meat and poultry is defrosted before placing in the oven.  
4. Whenever possible, keep food as cool as possible before placing in the oven,  
ideally straight from a refrigerator.  
5. If cooking food that requires frying before placing in the oven for auto cooking,  
keep the delay start time to a minimum.  
6. Never place hot or warm food in the oven for delay start cooking as it could  
cause the oven to be warm and produce harmful bacteria in the food.  
7. We advise that dishes containing left-over cooked poultry or meat, e.g.  
Shepherd's Pie, should not be cooked automatically if there is to be a delay  
period.  
8. Ensure that delay start times are kept to a minimum to prevent bacterial growth  
in food.  
9. Wine or beer may ferment and cream may curdle during the delay period so it is  
best to add these ingredients just before serving.  
10. Foods which discolour should be protected by coating in fat or tossing in water to  
which lemon juice has been added, prior to placing food in the oven.  
11. Dishes containing liquid should not be filled too full to prevent boiling over.  
12. Food should be well sealed (but not airtight) in a container to prevent the loss of  
liquid during cooking. Aluminium foil gives a good seal.  
13. Always ensure that food is piping hot and cooked thoroughly before serving.  
14. Only reheat food once.  
9
 
KNOW YOUR TIMER  
CLOCKFACE  
The timer incorporates a 24 hour clock.  
Ensure correct time of day is always set, before using your cooker.  
PLEASE NOTE THAT THE DISPLAY WILL DIM BETWEEN 22.00  
HOURS AND 06.00 HOURS TO PREVENT GLARE.  
However, should you operate the timer during these hours the display will  
return to normal brightness for a few seconds and then dim again.  
SYMBOLS  
will light up when you select a Minute Minder Period and will remain  
lit for the period set. At the end of the Minute Minder Period, the timer  
will emit an audible tone for 2 minutes, the symbol will start to flash  
and will continue to flash until the Minute Minder function is cancelled.  
This “Cookpot” symbol will light up either:–  
– When you press the Cook Period Button and set a length of time for  
an Auto Cooking Programme. (It will go out again a few seconds after  
you release the timer buttons).  
Minute Cook End  
Minder Period Time  
– During the actual Cook Period.  
Manual  
“AUTO” will light up:–  
– When the timer is first turned on it will flash. (It will go out when a time of  
day is set.  
A
U
T
O
– When an Auto Cooking Programme has been set.  
The “Auto” symbol will flash at the end of an Auto Cooking programme  
to indicate that the programme has finished.  
Minute Cook End  
Minder Period Time  
Manual  
(When the “Auto” symbol is flashing, to return the oven to Manual  
operation, turn the oven controls off, ensure that the correct time of day is  
set, and press the “Manual” button twice – The “Auto” symbol will go out.  
TIMER FUNCTION BUTTONS  
Minute Minder  
Button  
Here you can set a time period of up to 23 hours 59 minutes, that will count down.  
When it reaches zero, the timer will emit an audible tone.  
For Example: If you set 20 minutes, the audible tone will occur 20 minutes later.  
AUTO COOKING PROGRAMME  
Cook Period Button  
Cook Period is the actual length of time for which, the timer will switch the oven(s)  
on as part of an “Auto Cooking” programme.  
(e.g. If you set 2 hours, the food will be cooked for 2 hours).  
End Time Button  
The time of day at which you want an “Auto Cooking” programme to end.  
For Example: If you set a “Cook Period” for 2 hours, and “End Time” of 11:00. The  
timer will switch the oven(s) on at 9:00 and turn the oven(s) off at 11:00. You will  
hear a audible tone at 11:00, to indicate that the Auto  
Cooking Programme has finished.  
Notes:  
– When setting an Auto Cooking programme you will need to set the oven  
controls(s) to the required temperature(s) when you set the timer.  
_ If an Auto Cooking programme has been set the oven(s) will only operate during  
the pre-programmed time.  
Manual Button  
Needs to be pressed to cancel an Auto Cooking programme and return the  
ovens(s) to Manual operation.  
“+” and “–” Buttons  
Used to adjust the various timer function settings.  
10  
 
ELECTRONIC CLOCK & AUTOMATIC OVEN  
TIMER OPERATION  
SETTING THE TIME OF DAY  
A
U
Step 1 Make sure all oven controls are turned Off.  
T
O
Step 2 Check the electricity supply to the cooker is turned on.  
Minute Cook End  
Manual  
Minder Period Time  
Step 3 When switched on the display will show 0.00 and Auto symbol  
will be flashing intermittently.  
Step 4 Press & hold in both the “Minute Minder” & “Cook Period” button  
together.  
Step 5 With the “Minute Minder” & “Cook Period” buttons still held in,  
Minute Cook End  
Minder Period Time  
press either the “+” or “–” buttons to set the correct time of day.  
Manual  
Step 6 Release all the buttons simultaneously.  
THE TIME OF DAY IS NOW SET.  
To change the time of day repeat Steps 4, 5 & 6 above.  
Note: You cannot adjust the time of day if the timer has been set  
for an Auto Cooking Programme.  
Bell Symbol  
SETTING THE MINUTE MINDER  
Step 1 Ensure the time of day is set correctly.  
Step 2 Press and hold the Minute Minder Button, a symbol will light up.  
Minute Cook End  
Manual  
Step 3 With the “Minute Minder” button held in, set the required Minute  
Minder Period Time  
Minder time using the “+” and “–” buttons.  
Release all buttons and the timer display will revert back to the time of day.  
Bell symbol will remain lit to signify that a Minute Minder period has been set.  
At the end of the set time a bleeping sound will be heard, and the  
symbol will flash for approximately 2 minutes.  
After approximately 2 minutes the bleeping sound will stop and the  
symbol will go out automatically.  
Minute Cook End  
Manual  
Minder Period Time  
Step 4 To cancel the bleeping sound within the two minutes press the  
Minute Minder button.  
Note 1 When the Minute Minder has been set, the time remaining can be checked at  
any time by simply pressing the Minute Minder button.  
Note 2 If necessary the Minute Minder can be cancelled before the tone sounds by  
pressing and holding the Minute Minder button and then at the same time  
pressing the “–” button until 0.00 appears in the display window.  
11  
 
ELECTRONIC CLOCK & AUTOMATIC OVEN  
TIMER OPERATION  
AUTO COOKING PROGRAMMES  
There are two Auto Cooking programmes that can be selected using your timer:–  
(a) To set the timer to switch the oven(s) On and Off Automatically  
(b) To set timer to switch on immediately and OFF automatically after a set cook period.  
a) TO SET THE TIMER TO SWITCH THE OVEN(S) ON AND OFF AUTOMATICALLY  
This allows you to cook at a specified time for a chosen period before the oven  
switches off Automatically.  
Step 1 Check that the correct time of day is set, if not follow instructions for setting the  
time of day.  
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).  
Cooktop Symbol  
Step 3 Press and hold in the Cook Period button.  
The display will read 0.00 with the cookpot ( ) symbol lit.  
Step 4 With the Cook Period button still held in, set the required Cook  
Minute Cook End  
Minder Period Time  
Period using the “+” and “–” buttons.  
Manual  
A
Release the buttons and the timer display will revert to the time of day  
with the Auto symbol and Cookpot ( ) symbol lit.  
U
T
O
Step 5 Press and hold in the “End Time” button.  
A
U
The display will read the earliest possible end time for the Cook  
T
O
Period that you have set above.  
The Auto symbol and Cookpot ( ) symbol lit.  
Minute Cook End  
Minder Period Time  
Manual  
Step 6 With the End Time button still held in, use the “+” and “–”  
buttons to set the “End Time” (i.e. The time you require the oven  
to switch off).  
Release all the buttons and the timer will revert back to the time of day.  
A
U
The “Auto” symbol will remain lit to signify that an Auto Cooking  
Programme has been set. The ( ) symbol will go out.  
T
O
Minute Cook End  
Manual  
Minder Period Time  
Step 7 Turn the oven control(s) to the required temperature, and if  
necessary select the appropriate oven function.  
Note: If your appliance has two ovens: When the timer has been  
set for one oven it is possible to use the other oven only during the same  
Automatic programme.  
At the end of the Automatic Cook Period the Auto Symbol will flash and  
an intermittent bleeping sound will be heard.  
The bleeping sound will continue for approximately 2 minutes unless  
cancelled. The “Auto” symbol will continue to flash until the timer is  
returned to Manual operation (see below).  
Step 8 Press the Manual button to cancel the bleeping sound. (If 2  
Minute Cook End  
Minder Period Time  
minutes has not elapsed).  
Manual  
Step 9 Turn the oven control(s) to the OFF position.  
Step 10 Press the manual button again to return the oven(s) to Manual  
Operation. (The Auto symbol will go out)  
12  
 
ELECTRONIC CLOCK & AUTOMATIC OVEN  
TIMER OPERATION  
Note 1 When cooking automatically the Cook Period can be checked at any time  
by simply pressing the Cook Period button.  
Note 2 When cooking automatically the End Time can be checked at any time by  
simply pressing the End Time button.  
b) TO SET TIMER TO SWITCH ON IMMEDIATELY AND OFF AUTOMATICALLY AFTER A SET  
COOK PERIOD  
Step 1 Check that the correct time of day is set, if not follow instructions for setting the time  
of day.  
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).  
Step 3 Turn the oven control(s) to the required temperature, and if necessary select the  
appropriate oven function.  
Cookpot Symbol  
Step 4 Press & hold in the “Cook Period” button, the display will read  
0.00 and the cookpot ( ) symbol will light up.  
With the Cook Period button still held set the required Cook Period  
using the “+” and “–” buttons. Example: 1hr 30 minutes (as shown).  
Minute Cook End  
Minder Period Time  
Manual  
Note: Cook Period is the length of time the food requires to cook.  
Step 5 Release all buttons.  
A
U
The timer display will revert to the time of day with the Auto symbol lit &  
Cookpot symbol remaining lit.  
T
O
Note: Cookpot symbol disappears  
At the end of the Cook Period the “Auto” symbol will flash and an  
A
intermittent bleeping sound will be heard.  
U
The bleeping sound will continue for approximately 2 minutes unless  
T
O
cancelled. The “Auto” symbol will continue to flash until the timer is  
returned to Manual operation (see below).  
A
Step 6 Press the manual button to cancel the bleeping.  
U
(If 2 minutes has not elapsed)  
T
O
Minute Cook End  
Manual  
Minder Period Time  
Step 7 Turn the oven control(s) to the OFF position.  
A
Step 8 Press the “Manual” button again to return the cooker to Manual  
operation. (The Auto symbol will go out).  
Minute Cook End  
Minder Period Time  
Manual  
13  
 
ELECTRONIC CLOCK & AUTOMATIC OVEN  
TIMER OPERATION  
TO CANCEL AN AUTO COOKING PROGRAMME BEFORE  
THE COOK PERIOD HAS FINISHED.  
Step 1 Turn the oven control(s) to the OFF position.  
Step 2 Press and hold in the “Cook Period” button.  
Minute Cook End  
Manual  
Minder Period Time  
Step 3 With the “Cook Period” button still held in, return the display to  
0.00 by pressing the “–” button.  
A
U
T
Step 4 Release the “Cook Period” and “–” buttons and the display will  
O
revert to the time of day and the “Auto” symbol will flash.  
Step 5 Press the “Manual” button to return the oven(s) to “Manual”  
Minute Cook End  
Minder Period Time  
operation. The “Auto” symbol will go out.  
Manual  
Note 1  
When cooking automatically the Cook Period can be checked at any time by  
simply pressing the Cook Period button.  
OTHER NOTES ON TIMER OPERATION  
1. When cooking Automatically the Cook Period can be checked at any time simply by pressing the Cook  
Period button.  
2. When cooking Automatically the End Time can be checked at any time by simply pressing the  
End Time button.  
3. Having set a Cook Period and End Time an electronic device stores the information. The device  
within the timer will switch the oven(s) on and off at the required times.  
4. When setting an Auto Cooking Programme and a mistake is made, to clear:–  
(a) Press and hold in the “Cook Period” button.  
A
U
T
(b) With the Cook Period button still held in, return the display to  
by pressing the “–” button.  
O
(c) Release the “Cook Period” & “–” buttons, and the display will revert to the time of day and the  
“Auto” symbol will flash.  
(d) Press & release the “Manual” button.  
(e) Start the sequence again.  
5. If at any time the display shows three flashing zero’s 0.00. It is likely that the electricity supply  
to the oven has been interrupted. Reset the timer to the correct time of day.  
Food in the oven may, therefore, not have been cooked, before serving check food is  
thoroughly heated and completely cooked.  
6. To set each function always press and hold the required function button and at the same time press  
“+” or “–” buttons.  
Note: Between the hours of 22.00 & 06.00 the display dims to prevent glare.  
However, if you should operate a button during this period, the timer will return to normal  
brightness for a few seconds and then dim again.  
14  
 
GRILL PAN & HANDLE  
The grill pan handle is detachable from the pan, to facilitate cleaning and storage.  
The grill pan handle can be fixed as follows:  
A
B
C
Step 1 Remove screw & washers from the grill pan bracket.  
Step 2 Tilt the handle over the recess (A).  
Step 3 Slide it towards the centre of the pan (B).  
Step 4 Locate the handle over the bracket (C).  
For a fixed handle, replace screw & washers and ensure they are fully  
tightened up. If a detachable handle is required, do not replace screw &  
washers.  
NOTE:Ensure that when using the grill pan handle in the detachable  
manner it is centralised and secure.  
The grill pan can be stored in the compartment with the handle attached by  
tilting the grill pan over the rear edge of the shelf.  
If a fixed handle is required, the grill pan cannot be used as a meat pan.  
DOOR POSITION FOR GRILLING  
15  
 
USING THE GRILL  
CAUTION - ACCESSIBLE PARTS MAY BECOME HOT WHEN THE GRILL IS USED.  
YOUNG CHILDREN SHOULD BE KEPT AWAY.  
B
GRILL CONTROL  
Step 1 Remove the heat shield from the rear of an oven shelf and place the shelf in the  
top position.  
Step 2 Push in and turn the control knob anti - clockwise to the large flame symbol.  
Sparking will continue until the grill burner is lit.  
Step 3 Slide the grill pan along the shelf towards the rear of the compartment until it stops.  
Step 4 Turn the control knob anti-clockwise to the desired setting.  
Note: At the end of grilling always turn the control knob clockwise to the off symbol G.  
Note: DO NOT line the grill pan with aluminium foil, as this increases the amount of fat  
spitting and can cause a fire.  
The grill burner will only operate when the door is open. If the grill door is closed while  
the grill is on, the grill burner will be shut off. When the door opened again the grill  
burner will turn on and be reignited.  
Grilling can be started from cold but for best results preheat for approximately two minutes.  
Most cooking is done with the heat full on, but it may be desirable to reduce it for thicker pieces  
of meat or for keeping food warm.  
For au gratin dishes e.g. macaroni cheese and meringue toppings e.g. baked alaska, place the  
dish on an oven shelf at a suitable height.  
REMOVE HEAT SHIELD FROM  
SHELF WHEN GRILLING FOR  
MAXIMUM GRILLING AREA  
16  
 
USING THE OVEN  
Note: DO NOT allow young children near to the appliance when the main oven is in use as  
the surfaces get extremely hot  
The oven has different heat zones - the temperature control settings refer to the  
temperature on the middle shelf; above this shelf it is hotter and below it is cooler.  
SHELF POSITIONING  
The oven shelves have a heat shield fitted at the rear. The shield can be removed for  
cleaning and grilling, but should be replaced when using the oven.  
The two shelves can be used in five different positions. Each shelf has a safety stop to  
prevent it being pulled out too far when attending to food. Shelves are removed from  
the oven by pulling them out to the stop and the lifting at the front to withdraw.  
MAIN OVEN UTENSILS  
The grill pan without the handle can be used in the oven. To ensure good air  
circulation in the oven, the maximum size of baking tray that should be used is  
300mm X 350mm (12" X 14").  
MAIN OVEN OPERATION  
A
OVEN TEMPERATURE CONTROL  
1. Check that the timer is set to manual.  
2. Place the shelves in the correct position. ( see cooking chart ).  
3. With the main oven door closed, push in and turn the control knob fully  
anti - clockwise. Sparking will continue until the burner is lit. Turn the control  
knob clockwise to the required setting ( see cooking chart ). There is a delay of  
about one minute whilst the safety device operates before the burner comes  
fully on.  
4. Place the food on the shelf and ensure that the oven door is closed.  
Note: The oven burner only operates when the oven door is closed. The oven burner will  
shut off when the door is opened, and will turn on and reignite when the door is closed  
again. You may notice a slight smell of gas when you close the oven door. This is due to  
the short delay while the burner reignites and will soon disperse.  
At the end of cooking, always turn the control knob clockwise to the off symbol G.  
17  
 
USING THE OVEN  
COLD START COOKING  
Anything requiring long slow cooking such as casseroles and rich fruit cakes can be put  
into a cold oven. Satisfactory results can also be obtained with creamed mixture, rich  
pastries or yeast mixtures, but for perfection we recommend preheating the oven for  
about 15 minutes at the gas mark you require for cooking.  
ROASTING OF LARGE POULTRY  
The maximum weight of poultry that can be accommodated is 11.5kg (25 lbs) of suitable  
shape.  
It is important to check that the bird DOES NOT overhang the burner at the back of  
the oven.  
STORAGE AND RE-HEATING OF FOOD  
It is vitally important to strictly adhere to the basic principles of food handling and  
hygiene to prevent the possibility of bacterial growth.  
1. If food is to be frozen or not served immediately, cool it in a clean container as  
quickly as possible.  
2. Completely thaw frozen food in the refrigerator before re-heating.  
3. Re-heat food thoroughly and quickly either on the hotplate or in a hot oven, Mk. 6,  
and then serve immediately.  
4. Only re-heat food once.  
‘COOK CHILL’ DISHES  
These should always be placed in a pre-heated oven ideally on the first or  
second shelf position. Follow the packet instructions for cooking time.  
ALUMINIUM FOIL  
If using Aluminium Foil:  
1. Remember that it is important to increase the cooking time by one third.  
2. Never allow the foil to touch the sides of the oven.  
3. Never cover the oven interior with foil.  
4. Never cover the oven shelves with foil.  
18  
 
USING THE OVEN  
The ‘Slow Cook’ setting on the main oven thermostat is used for slow cooking, keeping food  
warm and warming plates for short periods.  
USING THE ‘SLOW COOK’ SETTING  
1. All dishes cooked by the ‘Slow Cook’ setting should be cooked for a minimum 6 hours.  
They will ‘hold’ at this setting for a further hour but marked deterioration in  
appearance will be noticed in some cases.  
2. Joints of meat and poultry should be cooked at Mk. 6 for 30 minutes before turning to  
the ‘Slow Cook’ setting and never be cooked lower than the middle shelf position.  
3. Joints of meat over 6 lbs (2.7kg) and poultry over 4 lbs 8oz (2 kg) should not be  
cooked using the ‘Slow Cook’ setting.  
4. Always stand covered joints on a rack over the meat tin to allow good air circulation.  
5. A meat thermometer should be used when cooking pork joints and poultry.  
The internal temperature of the food should reach at least 88oC.  
6. This method is unsuitable for stuffed meat and stuffed poultry.  
7. Always bring soups, casseroles and liquids to the boil before putting in the oven.  
8. Cover casseroles with foil and then the lid to prevent loss of moisture.  
9. Always thaw frozen food completely before cooking.  
10. Root vegetables will cook better if cut into small pieces.  
11. Adjust seasonings and thickenings at the end of the cooking time.  
12. Use the zones of heat in the oven, e.g. meringues and milk puddings can be cooked  
lower in the oven whilst other dishes requiring greater heat can be cooked above  
them.  
13. Egg and fish dishes need only 1-5 hours cooking and should be included in day  
cooking sessions, when they can be observed from time to time.  
14. Dried red kidney beans must be boiled for a minimum of ten minutes after soaking,  
before inclusion in any dish.  
19  
 
MAIN OVEN COOKING CHART  
The following times and setting are for guidance only. You may wish to alter the setting to give a  
result more to your satisfaction. When a different setting to that shown below is given in a  
recipe, the recipe instructions should be followed. Allow 15 minutes preheat for best results.  
Always turn the thermostat knob to Mark 9 before selecting the required Gas Mark.  
Shelf position 1 is the highest.  
Gas  
Shelf  
Food  
Mark  
Position  
Approx. Cooking Time and Comments  
20-30 mins.  
Push dish right to  
back of oven.  
FISH  
Oily and white fish  
MEAT AND POULTRY  
Beef (medium)  
Ham (covered in foil)  
Lamb  
5
2
4 or 5  
3
25-30 mins per lb + 25-30 mins  
40 mins per lb + 40 mins  
5
5
5
5
5
4
3
3
3
30-35 mins per lb + 30 mins  
40 mins per lb + 40 mins  
Pork  
3
3
Chicken  
25 mins per lb + 25 mins  
Duckling & Goose  
Turkey  
3
25 mins per lb + 25 mins  
4 or 3  
3
15-20 mins per lb + 15-20 mins  
2-4 hrs. depending on meat used.  
Casseroles  
VEGETABLES  
1
2
Baked jacket potatoes  
PUDDINGS  
5
2
1 / - 2 hrs.  
1
2
Milk Puddings (500ml/1pt)  
Baked Custard (500ml/1pt)  
Baked Sponge Puddings  
Baked Apples  
3
3
4
3
1
6
5
2
2
1 / - 2 hrs.  
45 mins - 1 hr. in bain-marie of cold water.  
30 - 45 mins  
2
2
45 mins - 1 hr. depending on size  
25 mins until tinged with brown  
50-60 mins, interchange at 30 mins  
45 - 50 mins  
Meringue Topped Puddings  
Apple Tart (205mm/8”)  
Fruit Crumble  
2
1+3  
2
If using aluminium foil:  
1. Remember it is important to increase the cooking time by one third.  
2. Do not allow the foil to touch the sides of the oven.  
3. Do not cover the oven interior with foil.  
4. Do not cover the oven shelves with foil.  
20  
 
MAIN OVEN COOKING CHART  
SHELF 1 IS THE HIGHEST.  
Gas  
Mark  
Shelf  
Positions  
Food  
Approx. Cooking Time and Comments  
CAKES, PASTRIES AND BISCUITS  
Small cakes - 12 per tray  
5
4
1 & 3  
1 & 3  
1
20 - 25 mins  
25 - 35 mins  
10 - 12 mins.  
Victoria sandwich (2 x 205mm / 8")  
Swiss Roll (3 egg quantity)  
Christmas cake (1 x 205mm / 8")  
Madeira cake (1 x 180mm / 7")  
Rich Fruit cake (1 x 180mm / 7")  
Gingerbread  
6
2
3
4 - 5 hrs depending on recipe  
1
2
4
3
1 - 1 / hrs  
1
1
4
2
2
3 or 4  
2
2 / - 2 / hrs.  
1
3
4
4
2
1 / - 1 / hrs  
Scones - 16 per tray  
7
1 & 3  
2
12 - 17 mins  
Shortbread - (1 x 180mm / 7")  
Biscuits  
3
55 - 1hr depending on thickness  
15 - 25 mins  
4 - 6  
6
1 and 3  
1 or 2  
2
Shortcrust pastry  
15 mins - 1 hr depending on recipe  
20 - 30 mins  
Rich Short crust  
5
Flaky / puff pastry  
7
1 or 2  
1 or 2  
10 - 30 mins depending on recipe  
25 - 35 mins  
Choux pastry  
6
YEAST MIXTURES  
Bread - Rolls, Plait  
7
5
2 or 3  
2 or 3  
25 - 35 mins  
25 - 30 mins  
Tea breads etc.  
MISCELLANEOUS  
Yorkshire Pudding - small  
7
7
1
1
1 or 2  
2
20 - 25 mins  
- large  
30 - 40 mins  
1
2
Meringues  
2 / - 4 hrs, turn when necessary  
When baking with two trays or tins on two levels, the top tray is removed first and the lower tray  
moved up to the top position for a few minutes longer.  
Soft Margarine – Use the oven settings recommended by the margarine manufacturer and not those  
indicated on the cooking chart.  
21  
 
CARE AND CLEANING  
Warning: Before cleaning, please ensure that the electricity supply to the appliance is switched off  
and the appliance is fully cold.  
1. “CREDACLEAN” OVEN LINERS  
(a) How "Credaclean" works.  
The surfaces of the "Credaclean" oven liners are  
treated with a special vitreous enamel which absorbs  
cooking soils. At temperatures of mark 7 or above, the  
special surface enables these soils to be slowly  
destroyed.The higher the temperature the more  
effective it is.  
(b) Cleaning.  
In most cases normal cooking operations at mark 7 will  
permit this cleaning operation to proceed during cooking.  
However if higher cooking temperatures are not used  
regularly, it may be necessary, in order to prevent heavy  
soiling, to run the ovens without shelves or meat pan, at  
mark 8 for about 2 hours. During this cleaning cycle,  
surfaces may become hotter than in normal use. Children  
should be kept away.  
MAIN OVEN SIDE LINERS  
AND REAR PANEL  
It should not normally be necessary to clean the  
"Credaclean" panels with water. If the user feels it is  
desirable to do so, wipe them over with a clean, soapy  
cloth, followed by a wipe with a clean damp cloth.  
DO NOT use biological washing powder, harsh abrasives or chemical oven cleaners of any kind as  
this could damage the “Credaclean” oven liners.  
2. CLEANING MAIN OVEN AND GRILL  
(a) Base of Main Oven.  
Wipe out the oven with a damp soapy cloth. For more  
stubborn stains on the base of the oven use a well soaped  
OVEN  
SHELVES  
fine steel wool soap pad.  
GRILL/  
MEAT  
PAN  
(b) Grill Pan, Meat Pans & Oven Shelves.  
To prevent stains from being burnt on to the grill pan,  
food support and rod shelf, always wash immediately  
after use in hot soapy water.  
MAIN  
OVEN  
BASE  
Use a well soaped fine steel wool soap pad to remove  
stubborn stains from the rod shelves, grill pan, meat  
pan and the base of the oven.  
22  
 
CARE AND CLEANING  
3. CONTROL PANEL / TRIMS / INNER DOOR PANEL & GLASS  
(a) Control Panel  
Regularly wipe with a clean, damp cloth and polish with a  
clean, dry cloth.  
(b) Trims  
It is advisable to clean the trims regularly to prevent  
any build up of soiling which may detract from the  
appearance of the cooker. The recommended method  
of cleaning is to wipe over the trims with a clean, soft  
cloth wrung out in hot water, or mild non abrasive  
cleaner. (If in doubt try the cleaner on a small area of trim  
which is not noticeable in normal use), then after wiping  
with a cloth wrung out in clear water, dry with a clean, soft  
cloth.  
OVEN  
DOOR  
(c) Inner Door Panels & Glass  
Open the door fully. The glass panel may now be  
washed. Stubborn stains can be removed by using a well  
soaped, fine steel wool soap pad.  
TRIMS  
DO NOT use scouring pads, or abrasive powder, which will  
scratch the glass.  
4. REPLACEMENT OF THE OVEN LAMP  
Warning: Before removing lamp lens, please ensure that the  
electricity supply to the appliance is switched off and the  
appliance is fully cold.  
Open the oven door and remove the oven shelves.  
Using a thick cloth, grip the lamp lens, unscrew anti-  
clockwise and remove the lens.  
Carefully unscrew the bulb anti-clockwise. Fit  
replacement bulb (25W 300°C SES). and refit lens.  
MAIN OVEN LAMP  
5. HOW TO CLEAN THE LAMP LENS  
Warning: Before cleaning lamp lens, please ensure that the  
electricity supply to the appliance is switched off and the  
appliance is fully cold.  
Open the oven door and remove the oven shelves.  
Using a thick cloth, grip the lamp lens, unscrew anti-  
clockwise and remove. Clean with a non-abrasive  
cleansing cream and refit lamp lens.  
DO NOT use scouring pads, or abrasive powder, which will  
scratch the glass lens  
MAIN OVEN LAMP  
23  
 
CARE AND CLEANING  
Take particular care not to damage the inner surface of the door inner glass that  
is coated with a heat reflective layer. Do not use scouring pads, or abrasive pow-  
der, which will scratch the glass. Ensure that the glass panel is not subjected to  
any sharp mechanical blows.  
Stubborn stains can be removed by using a fine steel wool pad. For slight soiling the  
inner glass panel may be cleaned, while still warm, without removing it from the door.  
After cleaning, rinse and dry with a soft cloth.  
CLEANING THE DOORS  
SIDE OPENING DOORS  
Cleaning the door glass is the same as the drop down doors, except take care to  
support the weight of the inner glass when removing and refitting.  
DROP DOWN DOORS  
Remove the door inner glass as follows.  
1.  
Open the door fully and unscrew the two screws securing the glass panel so that  
the securing brackets can be turned. There is no need to remove the screws  
completely.  
2.  
Turn the brackets so that the glass can be  
removed and cleaned at the sink (Fig. 1.)  
Fig. 1.  
Glass  
3.  
The inside of the outer door glass can now be cleaned while still fitted to the  
cooker.  
NEVER OPERATE THE COOKER WITHOUT THE INNER DOOR GLASS  
IN POSITION.  
Refit the door inner glass as follows.  
1.  
2.  
NOTE: The inner door glass has a special reflective coating on one side. Replace  
the door inner glass so that the statement: “IMPORTANT THIS FACE TOWARDS  
THE OVEN” can be read from the inner side of the door.  
Turn the two securing brackets back to their  
original position to retain the glass and tighten  
the screws. (Fig. 2.)  
Fig. 2.  
Glass  
24  
 
INSTALLATION INSTRUCTIONS  
Prior to installation, ensure that the local distribution conditions (nature of the gas and gas  
pressure) and the adjustment conditions are compatible. The adjustment conditions for this  
appliance are stated on the data badge which is fitted behind the bottom of the main oven door  
seal. This appliance is not designed to be connected to a combustion products evacuation device.  
It must be installed and connected in accordance with current installation regulations. particular  
attention should be given to the relevant requirements regarding ventilation.  
MODEL NUMBERS CB01G  
2H  
Category I (GB. IE)  
These models are set to burn NATURAL GAS (G20) only.  
GAS SAFETY (INSTALLATION & USE) REGULATIONS  
It is the law that all gas appliances are installed by competent persons in accordance with  
the current edition of the above regulations. It is in your interest and that of safety to  
ensure compliance with the law.  
In the UK, CORGI registered installers work to safe standards of practice. The  
appliance must also be installed in accordance with BS 6172. Failure to install the  
appliance correctly could invalidate the warranty liability claims and could lead to  
prosecution.  
LOCATION  
The appliance may be located in a kitchen, kitchen/diner or a bed-sitting room, but not  
in a room containing a bath or shower. The appliance must not be installed in a bed-  
sitting room of less than 20m3.  
PROVISION FOR VENTILATION  
The room containing the appliance should have an air supply in accordance with  
BS 5440: Part 2.  
The room must have an opening window or equivalent; some rooms may also require a  
permanent vent. If the room has a volume between 5 and 10m3, it will require an air vent  
of 50cm2 effective area unless it has a door which opens directly to outside. If the room  
has a volume of less than 5m3, it will require permanent air vent of 100cm2 effective area.  
If there are other fuel burning appliances in the same room, BS 5440: Part 2 should be  
consulted to determine air vent requirements.  
25  
 
INSTALLATION INSTRUCTIONS  
TECHNICAL DATA  
1/2 1/2  
Gas connection  
Gas supply  
Rp  
(
" BSP female)  
G20 at 20 mbar.  
Pressure test point  
Grill injector  
Electrical connection  
Flexible cord fitted with a 3 pin 13 amp plug.  
Z
230 - 240 a.c. 50H 3A fuse  
NATURAL GAS (G20)  
Heat Input  
3.7 kW  
Injector  
150  
Burner  
Grill  
110  
Oven  
2.5 kW  
1. GENERAL  
The appliance is designed for mounting at a safe level into an oven housing  
which must be secured to the backing wall. The appliance can be installed in a  
tall cabinet or alternatively under a worktop with or without a hob unit above.  
Maximum Hob Depth From Worktop  
Kitchen Worktop Thickness  
Surface Down  
30mm  
45mm  
55mm  
40mm  
40mm +  
Worktop Thickness + 15mm  
Note: The hob may project up to the worktop thickness + 30mm  
provided this is at least 100mm behind the front of the oven.  
It is important that the installation instructions for the hob are strictly observed.  
Where a hob is fitted above the oven unit the electrical connection for the hob should be made  
with an 85˚ C high temperature flexible cord to table 15 of BS 6141.  
A gas hob fitted above the oven unit should be connected to the gas supply with rigid  
tubing.  
26  
 
INSTALLATION  
2. VENTILATION  
a. The oven housing unit cabinet dimensions must comply with fig. 3 or fig. 4.  
b. An air gap of 30mm minimum must be provided at the rear of any top or bottom  
cupboards or shelves (see fig. 1).  
c. It is necessary that the cabinets are provided with unobstructed ventilation,  
i.e. from adjacent cabinetry. This can be done by either raising the base of the  
cabinets using the adjusting feet (or spacers) or alternatively by providing a slot in  
the cabinet plinth to the dimensions in fig. 1.  
d. The air gap at rear allows the warmed air to pass out of the inner cabinet space.  
Where it is intended to fit cupboards above the oven unit to ceiling height, it is  
essential that the warmed air is exhausted through the front of the cabinet  
(see fig. 1).  
e. If an oven unit is installed adjacent to a tall cabinet, steam escaping from the  
oven when the door is opened could condense on and maybe stain the  
adjacent surface. To prevent permanent staining, the adjacent surface should  
be made of a material that is heat resisting and easy to clean. Adjacent tall  
cabinets should not be deeper than the oven housing cabinet.  
3. FINAL INSTALLATION  
a. Using a spirit level, check that the housing cabinet is level from side to side  
and from front to back in its installed position.  
b. Correct any unevenness by placing spacers under the bottom of the cabinet.  
Make sure that the cabinet rests firmly on the floor without rocking.  
c. Before the oven is fitted, the cabinet must be firmly secured to the backing  
wall for stability.  
d. The oven unit should now be lifted (this is a two person lift) into the cabinet  
and pushed fully home.  
e. Finally, the oven is secured to the cabinet by means of the four Pozi Wash  
Head screws - two through each side trim.  
f. Remove all packaging material from the grill and oven interior.  
LIST OF LOOSE ITEMS  
4 x Pozi Wash Head No. 6 x 15mm screws.  
Note: This appliance must not be installed over any other appliance that  
generates heat.  
27  
 
INSTALLATION INSTRUCTIONS  
Ventilation Slot 150 cm2  
if cabinet doesn't fit to ceiling  
560mm  
Ventilation Slot  
150 cm2  
30mm  
air  
gap  
if cabinet fits  
to ceiling  
Fig. 1  
Viewed down through  
cabinet  
Oven  
Fig. 2  
Cabinet  
30mm  
air  
gap  
Ventilation Slot  
150 cm2  
Tall Cabinet  
Side  
Trim  
Oven Door  
When fitting a hob above an oven always  
No. 6 x 15mm  
(4 Supplied)  
use these installation instructions  
1.5mm  
in conjunction with the hob instructions.  
Fig. 3  
Built  
Under  
575mm min  
580mm max  
Ventilation Slot  
150 cm2  
28  
 
INSTALLATION INSTRUCTIONS  
Fig. 4  
The appliance can be installed into a cabi-  
net of minimum depth 550mm provid-  
Single Oven  
in tall  
Cabinet  
ing a suitable means of  
connection  
to the gas supply can be made.  
580mm max  
575mm if cooker  
trim is to  
overlap  
top edge  
of shelf  
*excluding pipes  
and other  
projections  
Ventilation Slot  
150 cm2  
29  
 
INSTALLATION INSTRUCTIONS  
CONNECTING TO GAS SUPPLY  
The oven is designed to be connected with an approved appliance flexible connection  
to BS 669. A length of 0.9 to 1.25m is recommended. An adaptor backplate should be  
fitted in the area shown to allow the appliance to be pushed fully back into the cabinet.  
The flexible hose should be fitted such that it cannot come into contact with moveable  
parts of the housing unit (e.g. a drawer) and does not pass through a space where it is  
likely to become trapped or damaged.  
The temperature rise of areas at the rear of the appliance that are likely to come in  
contact with the flexible hose do not exceed 70oC.  
200mm  
50mm  
CABINETS LESS THAN 565mm  
DEEP  
The appliance can be fitted into a cabinet of  
minimum depth 550mm providing a suitable  
connection to the gas supply can be made.  
The wall behind the appliance will need to  
be chased away behind the appliance gas  
inlet.  
The gas connection can either be made with  
a flexible hose or 8mm minimum diameter  
rigid piping, leading below or to the sides of  
the appliance. Where rigid piping is used, an  
accessible isolation tap with suitable means  
of disconnection must be provided to allow  
for servicing.  
30  
 
ELECTRICAL CONNECTION  
WARNING – THIS APPLIANCE MUST BE EARTHED.  
CONNECT TO A 230-240V A.C. SUPPLY ONLY.  
Connection to the electricity supply should be made via a properly earthed, readily accessible wall  
socket which is adjacent to, and not more than 1.25m away from the appliance and capable of  
electrical isolation.  
The mains lead should be routed such that it cannot touch hot parts of the appliance i.e. the back  
panel above a height of 350mm from the bottom of the oven recess. If the oven is to be wired into a  
connector unit, this may be positioned behind the oven providing the following requirements are  
met:  
i) The connector unit must not project more than 25mm from the wall.  
ii) The top of the connector unit must not be more than 350mm above the base of the oven recess.  
NOTE: The removed plug cannot be used for any other appliance and should therefore be  
properly disposed of and not left where children might find it and plug it into a supply  
socket – with the obvious consequent danger.  
IF THE FITTED PLUG IS REMOVED  
The flexible mains lead must be correctly connected as below to a three pin plug of not less  
than 13 amp capacity. If a B.S. 1363 fused plug is used, it must be fitted with a 3 amp fuse  
which is approved to B.S. 1362.  
IMPORTANT: The wires in the mains lead fitted to this  
appliance are coloured in accordance with the  
following code:  
Green &  
Yellow to  
Earth  
GREEN AND YELLOW – EARTH  
Brown to  
Live  
BLUE  
– NEUTRAL  
– LIVE  
Blue to  
Neutral  
BROWN  
3 Amp  
Fuse  
Cord Clamp  
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured  
markings identifying the terminals in your plug, proceed as follows:– The wire which is coloured green  
and yellow must be connected to the terminal in the plug which is marked with the letter E or by the  
earth symbol  
or coloured green or green and yellow. The wire which is coloured blue must be  
connected to the terminal which is marked with the N or coloured black. The wire which is coloured  
brown must be connected to the terminal which is marked with the letter L or coloured red. When  
wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to  
tighten the mains lead clamp on the plug. As the appliance must be earthed, do not use 2-pin sockets  
outlets, if you are in doubt, consult a qualified electrician.  
Should the mains lead ever require replacement, it is essential that this operation be carried out by a  
qualified electrician and should only be replaced with a flexible cord of the same size i.e. 0.75mm2  
cross sectional area and temperature rating of 85˚ C e.g. heat resisting PVC.  
IF A MOULDED PLUG IS FITTED  
In the event of replacing a fuse in the plug supplied a 3 amp ASTA approved fuse to BS1362 must be  
fitted.  
NOTE: The fuse cover must be refitted when changing the fuse. In the event of losing the  
fuse cover the plug must not be used until a replacement fuse cover has been obtained and fitted. A  
new fuse cover can be obtained from your local electrical retailer. The colour of the correct replace-  
ment fuse cover is that of the coloured marks or inserts in the base of the plug.  
31  
 
INSTALLATION INSTRUCTIONS  
INSTALLATION AND OPERATIONAL CHECKS  
Note: These checks should only be carried out by a competent person  
(eg. CORGI registered)  
After installation, check for gas soundness. The supply pressure can be checked at the  
grill injector. Loosen the fastening screw on the left hand side of the grill burner and slide  
the burner to the right and then off the injector. Ensure that the grill burner is correctly  
located and the fixing screw tightened on reassembly.  
As the door switch prevents the grill burner and oven burner operating at the same  
time a bypass switch is provided to allow the supply pressure to be checked at the grill  
injector with the oven burner operating. The switch is located behind the ventilation  
slots below the door, on the right hand side.  
1.  
2.  
3.  
Remove the oven door as shown in the cleaning instructions.  
Measure the supply pressure at the grill injector as above.  
Turn the oven on at the thermostat, and depress and hold in the bypass switch  
button while the flame safety device opens to full rate. This can be done by  
pushing a screwdriver or similar tool through the ventilation slot in front of the  
bypass switch.  
4.  
5.  
Refit the oven door and grill burner.  
Check that the grill burner ignites correctly and burns with a steady flame. Check  
for a steady flame on the low setting.  
6.  
7.  
Check that, with the main oven set to mark 9, the burner ignites at low rate, and  
then increases to full rate within 60 seconds. Leave the oven full on with the door  
closed for 10 minutes, and check that when the control is turned to the ‘Slow  
Cook’ setting that the flame reduces.  
Check the operation of the oven timer, oven light(s) & cooling fan.  
Instruct the user on operation of the appliance.  
32  
 
SOMETHING WRONG?  
Before calling a Service Engineer, please check through the following lists.  
THERE MAY BE NOTHING WRONG.  
Problem  
Nothing works.  
Check  
If the timer display is blank.  
Then it is likely that there is no electricity supply to your oven.  
Check: (i) That the main cooker wall switch is turned on.  
(ii) Check other appliances to see if you have a power  
cut.  
(iii) Check the main circuit breaker for the property.  
Display shows 0.00 AUTO.  
The power supply to your oven has possibly been interrupted, but has  
now come back on again. Reset the timer to the correct time of day and  
"Manual" operation using instructions given in the timer section of the  
book.  
Timer display shows " Auto " lit up  
or flashing.  
To use the ovens or grill the timer must be set to manual mode. See timer  
instructions.  
Timer display correct but  
appliance will not operate  
The appliance incorporates a safety device to shut down the burners in  
the event of a fault, to prevent overheating.  
In this case contact your service engineer to have the fault rectified and  
the safety device reset.  
Can not set an “Auto Cook”  
programme  
Remember that " Cook period " is the actual length of time for which  
the timer will switch the oven(s) on as part of an "Auto cooking "  
programme.  
A gentle flow of air will be blown from beneath the control panel when  
the appliance is used. If the appliance is still warm, this cooling fan may  
continue to run, or restart itself after all controls have been turned off.  
The fan will stop once the appliance has cooled.  
Draught from beneath control  
panel.  
If no air is blown from below the control panel when the controls are  
switched on and you have checked through the " Nothing works "  
section above, then the cooling fan may be faulty. In this case you  
should turn off the appliance and contact your service agent to arrange  
for a repair.  
Cooling fan not operating  
Oven burner not working  
Note that the oven burners only operate when the door is closed to  
ensure safe operation and avoid wasting heat. With the door closed the  
oven burner will ignite.  
This is due to the short delay while the burner reignites and will soon  
disperse.  
Slight smell of gas after closing  
oven door.  
It may be necessary to turn to a lower setting than shown on the cook-  
ing chart or recipe as results depend on personal tastes.  
Oven appears to be cooking at too  
high a temperature.  
If the oven appears to be cooking at too high a temperature than  
previously, and turning down the thermostat has no effect, then the  
thermostat may be faulty and you should contact your service agent.  
Timer buzzer/bleeper operates  
continually  
Buzzer / bleeper should stop automatically after two minutes. If not.  
press minute minder button to silence.  
If you have been through the above list and there is still a problem;  
Contact Service (see Key Contacts, back page).  
33  
 
 
 
Key Contacts  
Service  
Creda has the largest appliance manufacturer’s service team in Europe, trained  
specialists directly employed by us to ensure your complete confidence.  
Repair Service  
UK: 08709 066 066  
Republic of Ireland: 1850 302 200  
You will be asked for the following information:-  
Name, address and postcode.  
Telephone number  
Model / Serial number of the appliance  
Clear and concise details of the query or fault  
Place and Date of purchase  
(Please keep the receipt as evidence will be required when the engineer calls).  
Extended Warranty  
To join: UK 08709 088 088  
Republic of Ireland: 1850 502 200  
Genuine Parts & Accessories  
Mail Order Hotline  
UK: 08709 077 077  
Republic of Ireland: (01) 842 6836  
For further product information 08701 546474  
All Creda Services are offered as an extra benefit and do not affect your statutory rights.  
General Domestic Appliances Limited, Morley Way, Peterborough, PE2 9JB  
.
PRINTED BY SIMLEX FOUR ASHES, WOLVERHAMPTON.  
September 2001 Part No. 4866200096-02  
 

Coleman Impact Driver 024 0075CT User Manual
Cooper Lighting Indoor Furnishings C600EL User Manual
Crate Amplifiers Musical Instrument Amplifier XK100 User Manual
Crown Audio Microphone BF 100 SUX User Manual
Cuisinart Rice Cooker CRC 400C User Manual
Curtis DVD Player DVD1098 User Manual
Curtis Stereo System SRCD909 User Manual
DXG Technology Camcorder DXG 599V User Manual
Fundex Games Board Games 10 Game Set User Manual
GE Ventilation Hood JV694 User Manual