GT65/212
Three-channel Guitar Amplifiers
Owner’s Manual
GT65/212 Guitar Amplifier
Congratulations!
You are now the proud owner of the Crate GT65/212
three-channel guitar amplifier. This rugged amplifier combines
outstanding features with serious clean and distorted sounds.
Front panel RCA input jacks allow you to play along with your
favorite CD or tape. The rear panel Insert Jack allows you to
connect your effects for greater flexibility. Channel switching
and reverb may be controlled by means of a footswitch.
Like all Crate products, your GT amplifier is designed by
musicians, and built using only the best components.
Extensive testing confirms that this amplifier is the absolute
best it can be.
In order to get the most out of your new amplifier, we
strongly urge you to read the information contained in this
manual before you begin playing.
And thank you for choosing Crate.
Declaration Of Conformity
#30, Effective 01-01-2001
Manufacturer’s Name:
SLM Electronics
Production Facility:
Production Facility:
Shipping Facility:
Office Facility:
11880 Borman Drive, St. Louis, MO 63146, USA
700 Hwy 202 W, Yellville, AR 72687, USA
1400 Ferguson Ave., St. Louis, MO 63133, USA
1400 Ferguson Ave., St. Louis, MO 63133, USA
Product Type:
Audio Amplifier
Complies with Standards:
LVD:
Safety:
EMC:
92/31/EEC, 93/68/EEC, & 73/23/EWG
EN60065
EN55013, EN55020, EN55022, EN61000-3-2,
& EN61000-3-3
Supplementary information provided by:
SLM Electronics - R & D Engineering
1901 Congressional Drive, St Louis, MO 63146, USA
Tel.: 314-569-0141, Fax: 314-569-0175
3
GT65/212 Guitar Amplifier
The Front Panel:
1
2
3
4
5
6
7
8
9
10
11
12
1: INPUT: Use this jack to connect your guitar to the amplifier by means of a shielded instrument cable.
SOLO/RHYTHM CHANNELS: High gain channels giving you sounds with serious overdrive.
2: SOLO LED: This LED illuminates when the Solo channel is selected.
3: GAIN: Use this control to adjust the amount of distortion produced by the Solo channel.
4: SHAPE: Use this control to “dial in” the tone for the Solo channel. Rotating the control counterclockwise
enhances the mid frequencies, while rotating the control clockwise enhances the low and high frequencies.
5: LEVEL: Use this control to adjust the output level of the Solo channel.
6: SOLO/RHYTHM SELECT: Use this switch to select the Solo or Rhythm channel. When this switch is
depressed, the Solo channel is selected. With the switch in the out position, the Rhythm channel is select-
ed. This switch is active only when the Solo-Rhythm/Clean Select switch (#13) is depressed.
7: RHYTHM LED: This LED illuminates when the Rhythm channel is selected.
8: GAIN: Use this control to adjust the amount of distortion produced by the Rhythm channel.
9: LOW: Use this control to adjust the low frequency level of the Solo/Rhythm channel.
10: MID: Use this control to adjust the midrange frequency level of the Solo/Rhythm channel.
11: HIGH: Use this control to adjust the high frequency level of the Solo/Rhythm channel.
12: LEVEL: Use this control to adjust the output level of the Rhythm channel.
13: SOLO-RHYTHM/CLEAN SELECT: Use this switch to select the Clean channel or the Solo and
Rhythm channels. With the switch in the out position, the Clean channel is selected. When the switch is
depressed, either the Solo or Rhythm channel is selected, depending on the setting of the Solo/ Rhythm
Select switch (#6).
CLEAN CHANNEL: A normal gain channel designed to give you crystal clean sounds.
14: CLEAN LED: This LED illuminates when the Clean channel is selected.
15: VOL: Use this control to adjust the output level of the Clean channel.
16: LOW: Use this control to adjust the low frequency level of the Clean channel.
17: MID: Use this control to adjust the midrange frequency level of the Clean channel.
18: HIGH: Use this control to adjust the high frequency level of the Clean channel.
19: REVERB: Use this control to adjust the amount of reverb effect: in its fully counterclockwise position
the signal will be “dry” (without any effect). As you rotate the control clockwise the amount of reverb increas-
es.
20: CD INPUT: Use these RCA jacks to connect the output from a CD player or tape deck to the amplifier.
The signal at these jacks is combined into a mono signal which is sent to the internal power amp circuit.
Use the CD or tape player’s output level control to adjust the signal for the proper mix with your guitar.
4
GT65/212 Guitar Amplifier
13 14 15
16
17
18
19
20
21
21: POWER: Use this switch to turn the amplifier on (top of the switch depressed) and off (bottom of the
switch depressed). The switch illuminates when the power is on.
The Rear Panel:
100VAC:T2.5A
120VAC:T2A
230/240VAC:T1.25A
250V
250V
EXTENSION
SPEAKER
REVERB
CLEAN/
SOLO/
INSERT
250V
RHYTHM
CAUTION: TO REDUCETHE RISK OF FIRE,
REPLACE FUSE WITH SAME TYPE AND RATING.
FOOTSWITCH
ATTENTION: UTILISER UN FUSIBLE DE
RECHANGE DE MEME TYPE.
22
23
24
25
26
22: FUSE: The fuse protects the amplifier from damages caused by a faulty AC power source and/or
other problems. If the fuse opens, replace it ONLY with the same size and type. If fuses continue to
fail, check the AC source – if the source is okay, contact your Crate dealer for service information.
23: EXTENSION SPEAKER: Use this jack to connect the amplifier to an external speaker cabinet.
This jack is wired in series with the internal speaker(s) which remain active when an extension
speaker is connected.
24: REVERB FOOTSWITCH: Use this jack to connect the 1/4” mono plug on the footswitch cable to
the three-button footswitch (supplied). This allows you to remotely turn the reverb on and off.
25: CLEAN/SOLO/RHYTHM FOOTSWITCH: Use this jack to connect the 1/4” stereo plug on the
footswitch cable to the three-button footswitch (supplied). This allows you to remotely switch between
the Clean and Distortion channels and between the Solo and Rhythm channels.
26: INSERT: Use this jack to connect an external
Stereo-to-mono Y-cord:
Y-adapter and 2 cables:
effects device to the amplifier. Use Crate’s
STP201, STP202, or STP203 stereo-to-mono Y-
cord or an adapter such as Crate’s YPP117 and
two 1/4” mono signal cables to connect to the
effect as shown to the immediate right.
TIP
RETURN
TIP
to Insert
to Insert
jack
RING
SEND
RING
jack
SLEEVE
GROUND
SLEEVE
(STP201, 3'
STP202, 6'
STP203, 9')
(YPP117)
27: AC LINE CORD (not shown): This grounded
power cord is to be plugged into a grounded power
outlet, wired to current electrical codes and compati-
ble with the voltage, power, and frequency require-
ments stated on the rear panel. Do not attempt to
defeat the safety ground connection.
(1/4"-TO-1/4"
MONO CABLES)
to
to
effect
"IN"
to
to
effect
"IN"
effect
"OUT"
jack
effect
"OUT"
jack
jack
jack
External Effect
External Effect
5
GT65/212 Guitar Amplifier
Suggested Settings:
Sweet 'n Clean:
Just a 'Lil Nasty:
Politely Gritty:
Down 'n Dirty:
OUT
OUT
OUT
OUT
IN
IN
IN
Mean & Obscene:
6
GT65/212 Guitar Amplifier
System Block Diagram:
BUFFER
INPUT
CLEAN CHNL
VOL LOW MID HIGH
SOLO-RHTM/
CLEAN
SELECT
SOLO
SOLO
RHTM
RHTM
SOLO
SOLO
RHTM
SWITCHING
CIRCUIT
LEVEL
SOLO/ RHTM
SELECT
RHTM
LEVEL
SOLO
GAIN
RHTM
GAIN
SHAPE
LOW MID HIGH
MIX
AMP
INSERT
REVERB
POWER
AMP
SPEAKER
CD
INPUT
EXT.
SPEAKER
DAMPING
CIRCUIT
7
GT65/212 Guitar Amplifier
GT65/212 TECHNICAL SPECIFICATIONS:
Output Power Rating
GT65
65W RMS @ 5% THD, 8Ω, 120 VAC
120W RMS @5% THD, 4Ω, 120 VAC
GT212
Speaker Size and Rating
GT65
(1) Custom Design 12”, 8Ω
(2) Custom Design 12”, 8Ω
GT212
Input Impedance
Total System Gain
470kΩ
Solo Ch
Rhythm Ch
Clean Ch
110dB, all controls @10
88dB, all controls @10
58dB, all controls @10
CD Input
29dB
Maximum Input Signal Accepted
7 volts peak-to-peak
Proprietary Circuit
Solo Channel
Shape Control
Rhythm Channel
Low Control
Mid Control
High Control
20dB range @ 80Hz
15dB range @ 1kHz
20dB range @ 10kHz
Clean Channel
Low Control
Mid Control
High Control
36dB range @ 80Hz
15dB range @ 800Hz
40dB range @ 10kHz
Power Requirements
GT65
120 VAC, 60Hz, 90VA
100/115VAC, 50/60Hz, 90VA;
230VAC, 50/60Hz, 90VA
120 VAC, 60Hz, 95VA
GT212
100/115VAC, 50/60Hz, 95VA;
230VAC, 50/60Hz, 95VA
Size and Weight
GT65
17-1/2” H x 20” W x 11” D, 34 lbs.
21” H x 26-1/2” W x 11” D, 50 lbs.
GT212
The GT65/212 is covered with a durable Tolex material: wipe it clean with a lint-free cloth.
Never spray cleaning agents onto the cabinet. Avoid abrasive cleansers which would damage the finish.
Crate continually develops new products, as well as improves existing ones. For this reason, the specifications
and information in this manual are subject to change without notice.
@2002 SLM Electronics, a division of St. Louis Music, Inc • 1400 Ferguson Avenue • St. Louis, MO 63133
47-432-01 • 012903
|