I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Istruzioni di installazione
Installatie-instructies
Instruções de Instalação
Instructions d´installation
Truss Ceiling Adapter Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
CMA365
Installation Instructions
CMA365
LEGEND
Tighten Fastener
Open-Ended Wrench
Llave de boca
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Clé à fourche
Loosen Fastener
Hex-Head Wrench
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Zeskantsleutel
Clé à tête hexagonale
TOOLS REQUIRED FOR INSTALLATION
5/32"
(Provided)
3/8"
PARTS
A (1)
B (2)
E (4)
3/8"
C (1)
5/16-18 x 1/4"
D (4)
3/8"
F (1)
5/32"
3
CMA365
Installation Instructions
ASSEMBLY AND INSTALLATION
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
1. Place two U-bolts (B) over supporting truss or pipe and
insert through holes in truss plate (A). (See Figure 1)
NOTE: If mounting truss plate (A) to pipe, ensure that pipe fits
into notches in plate. (See Figure 1)
2. Loosely install 3/8" nuts (E) and 3/8" washers (D).
NOTE: The washers (D) are only used for temporary
installation of the CMA365. Washers MUST be
removed before permanent installation.
3. Level mount and tighten nuts (E).
4. Install 1-1/2" NPT threaded column (purchased separately)
into threaded collar until tight.
5. Install and securely tighten set screw (C) using the 5/32"
hex wrench (F).
(B) x 2
5
(C) x 1
Supporting Pipe
(A)
Pipe should fit
into notches
1
(D) x 4
2
(E) x 4
3
Figure 1
4
Installation Instructions
CMA365
5
CMA365
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Chief Manufacturing, a division of
Milestone AV Technologies
Asia Pacific
A
Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
8803-000023 Rev C
¤2008 Milestone AV Technologies
06/08
P
F
+86-755-8996 9226
+86-755-8996 9217
|