I N S T A L L A T I O N I N S T R U C T I O N S
HEAVY DUTY FIXED WALL MOUNT
Model: PSH-2000
Specifications:
•
Accomodates Akira and Orion 84" displays
without interface bracket; accomodates other
large flat panel displays with optional interface
bracket.
NOTE: Interface bracket, if required, will result in
additional installation depth. Contact Chief for
details.
•
•
Designed for installation on dual wood studs (16"
or 24" on center).
Weight capacity of 250 lbs (113 kg).
BEFORE YOU BEGIN
CAUTION: To prevent damage to your display and this unit, which could affect or void the factory warranty,
thoroughly study all instructions and illustrations before installation. Pay particular attention to the Warnings and
Cautions in this document.
•
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-894-
6280.
8805-000067 Rev F
CHIEF MANUFACTURING INC.
1-800-582-6480 952-894-6280 FAX 952-894-6918
8401 EAGLE CREEK PARKWAY, STE 700
SAVAGE, MINNESOTA 55378 USA
©2006 Chief Manufacturing
01/06
Installation Instructions
Model: PSH-2000
TOOLS REQUIRED FOR INSTALLATION
•
•
•
•
•
•
•
Drill and 7/32" drill bit
13mm wrench
Table 1: Parts
1/2" wrench
Item
10
Description
Qty
2
Phillips screwdriver, #2
M5 Hex Key (provided)
3/16" Hex Key (provided)
5/32" Hex Key (provided)
PLATE, Wall
20
BRACKET, Static
BRACKET, Side Support
LATCH
2
30
2
40
2
50
SPACER, 0.194" ID x 0.375" OD x 0.032"
SCREW, Button Head Cap, 10-24 x 1/2"
SCREW, Phillips Pan Machine, 10-24 x 1-1/2"
SCREW, Button Head Cap, M8-1.25 x 25mm
BUTTON, Mounting
8
8
2
6
6
6
6
6
24
1
1
1
8
NOTE: Other tools may be required depending on your
method of installation.
60
70
80
PARTS
90
Unpack carton, inspect and verify contents
100
110
120
130
140
150
160
WASHER, Flat, Machine, M8
(See Figure 1). Read installation instructions completely.
If any listed parts are missing or damaged, contact Chief
Customer Service at 1-800-582-6480.
WASHER, Lock, Split, M8
NUT, Hex, Finished Standard, M8
SCREW, Button Head Cap, 5/16"-18 x 1/2"
KEY, Hex, M5 (Slightly larger than 150)
KEY, Hex, 3/16"
KEY, Hex, 1/8"
BOLTS, Hex Head Lag, 5/16" x 2-1/2"
(Required, not supplied)
WASHER, Flat, Machine, 5/16" (Required, not
supplied)
8
(20)
(10)
(30)
(40)
(50)
(60)
(70)
(80)
(90)
(100)
(110)
(120)
(130)
(140)
(150)
(160)
Figure 1: Parts
3
Model: PSH-2000
Installation Instructions
ASSEMBLY AND INSTALLATION
NOTE: Read the Warnings and Cautions on page 2.
INSTALL MOUNTING BUTTONS
Installation of the mounting buttons is dependent on your
specific display. Three options are provided:
•
•
•
Akira 84" and Orion 84" displays
Modular 84" displays
Other large flat panel displays
Install buttons (90) at these
6 mounting hole locations.
AKIRA 84" AND ORION 84" DISPLAYS
1. Using key (140), insert screw (80) through button (90)
and install into threaded mounting hole on back of
Figure 3: Modular Display Frame
2. Repeat for remaining five buttons.
(90)
Mounting Hole
(90)
(80)
(120)
(110)
(100)
Modular
Frame
(80)
Install buttons (90) at these
6 mounting hole locations.
Figure 4: Modular 84" Mounting Button
OTHER LARGE FLAT PANEL DISPLAYS
Figure 2: Akira 84" and Orion 84" Mounting Button
1. Install the optional interface bracket to display
according to the instructions provided with the
interface bracket.
MODULAR 84" DISPLAYS
NOTE: Modular displays are four independent displays
attached together within a single frame. The
assembly performs as a single display.
NOTE: Mounting buttons are pre-installed on optional
interface bracket. PSH-2000 items (80) through
used with optional interface bracket.
1. Insert screw (80) through button (90) and frame on
Using key (140) and 13mm wrench, install washer
(100), washer (110), and nut (120). Tighten securely.
2. Repeat for remaining five buttons.
4
Installation Instructions
Model: PSH-2000
ASSEMBLE STATIC BRACKETS
ASSEMBLE SIDE SUPPORTS
1. Using key (160), loosely install screws (60) through
latch (40) and spacers (50) into threaded holes in
installed on the end of bracket (20) with the square
cutout.
1. Using key (150), loosely install support (30) to plate
support (30) covers edge of plate (10).
2. Repeat for other 3 corners.
3. Once all screws (130) are installed, tighten securely.
Threaded
Hole in
(40)
(130)
Bracket
(4 Places)
(10)
(50)
(4 Places)
(60)
(4 Places)
Square
Cutout
(20)
(30)
Figure 5: Latch Assembly
2. Repeat for remaining bracket (20).
Figure 7: Side Support Assembly
3. Tighten screws (60) only as required to keep latches
(40) from freely slipping on bracket (20). Latches are
designed to slide; do not overtighten screws (60).
4. Slide latch (40) to fully open (raised) position.
5. Using Phillips screwdriver, install screw (70) through
slotted hole in latch (40) into threaded hole in bracket
up slack; overtightening will close latch preventing
mounting button installation.
•
If latch begins to close, loosen screw (70) and pull
latch (40) to open position.
(70)
Slotted Hole
in Latch (40)
Threaded Hole
in Latch (40)
Threaded Hole
in Bracket (20)
Figure 6: Open Latch
5
Model: PSH-2000
Installation Instructions
INSTALL MOUNT TO WALL
1. Determine approximate mounting location, keeping in
mind the display size.
Left of center installation
Lag Bolt & Washer
(8 Places)
WARNING: The mount must be installed on two or
three wood studs (or other equivalent vertical or
horizontal supporting framework). Do not mount to
single wood studs. Failure to properly install unit can
result in serious personal injury or damage to
equipment!
2. Use a stud sensor to locate applicable wood studs.
Mark locations with a pencil.
3. Level mount at desired height per one of the
configurations below:
NOTE: Either configuration below provides ± 2" of lateral
shift.
Lag Bolt &
Washer
(8 Places)
•
•
16" on center studs: The mount is approximately
centered between two or three studs as shown
Right of center installation
24" on center studs: The mount is offset to the left
or right of center between two studs as shown
Figure 9: 24" On Center Installation
4. Using mount as a template, mark the location of the
pilot holes. Ensure the following:
Centered between 2 studs
•
•
Marks are in the center of wood studs.
Lag Bolt &
Washer
(8 Places)
8 pilot holes are marked (one in each slot).
NOTE: For 16" on center, 3 stud installation: Lag bolts
and washers on center stud are optional.
5. Drill pilot holes using a 7/32" drill bit. Ensure pilot
holes are straight.
6. Using 1/2" wrench, install eight 5/16" x 2 ½" lag bolts
and eight 5/16" washers through mounting holes and
into pilot holes. Tighten all lag bolts.
NOTE: Lag bolts and washers are not supplied.
Lag Bolt &
Washer
(8 Places)
Centered between 3 studs
Figure 8: 16" On Center Stud Installation
6
Installation Instructions
Model: PSH-2000
2. Using key (150), loosely install brackets (20) to plates
(10) with screws (130) according to dimension noted
in previous step. Ensure that brackets (20) are
installed so that the latches (40) are towards the top
of the mount.
INSTALL STATIC BRACKETS
AKIRA 84", ORION 84", AND MODULAR 84"
DISPLAYS
1. Using key (150), loosely install brackets (20) to plates
following:
•
14" horizontal dimension: Install brackets (20) to
inside set of mounting holes, closest to center of
mount (See Figure 12).
•
Brackets (20) are installed to outside set of
mounting holes, closest to supports (30).
•
•
24" horizontal dimension: Install brackets (20) to
middle set of mounting holes (See Figure 13).
•
Brackets (20) are installed so that latches (40) are
towards top of mount.
33" horizontal dimension: Install brackets (20) to
outside set of mounting holes, closest to supports
(30) (See Figure 10).
2. Tighten all 16 screws (130) securely.
3. Tighten all 16 screws (130) securely.
(130)
(16 Places)
(130)
(16 Places)
Figure 10: Installation on Outside Mounting Holes
OTHER LARGE FLAT PANEL DISPLAYS
Figure 12: Installation on Inside Mounting Holes
1. Determine horizontal dimension between mounting
buttons on back of display (or interface bracket, if
required) (See Figure 11).
(130)
(16 Places)
Mounting Buttons
(6 buttons shown;
4 buttons similar)
Figure 13: Installation on Middle Mounting Holes
Back of Display
Figure 11: Horizontal Dimension
7
Model: PSH-2000
Installation Instructions
5. Repeat for second latch (40).
INSTALL DISPLAY
6. Connect cables to display as required.
WARNING: Display is very heavy! Ensure display can
be safely lifted and maneuvered as required to install
on mount. Failure to take adequate precautions can
result in serious personal injury or damage to
equipment!
REMOVE DISPLAY
WARNING: Display is very heavy! Ensure display can
be safely lifted and maneuvered as required to remove
from mount. Failure to take adequate precautions can
result in serious personal injury or damage to
equipment!
1. Ensure latches (40) are in fully open (raised) positions
2. Note button openings to be used on each bracket (20)
when installing display (See Figure 14).
1. Disconnect all cables from display.
2. Using Phillips screwdriver, fully remove screw (70)
3. Re-install screw (70) into threaded hole in latch (40).
Turn screw (70) until latch (40) slides into fully open
position.
4. Repeat for second latch (40).
5. Lift and maneuver display mounting buttons (90) out
of button openings.
Six
Button
Installation
Four
Button
Installation
(20)
Figure 14: Mounting Holes
3. Lift and maneuver display such that all buttons (90) fit
into button openings on brackets (20). Lower display
firmly into place. Ensure each button (90) has fully
seated in its button opening.
4. Using Phillips screwdriver, tighten screw (70) until
(70)
(40)
Figure 15: Closed Latch
8
|