10.8 VOLT CORDLESS DRiVER
Model 96298
OPERATiNG iNSTRUCTiONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT SERiOUS iNjURy, READ
AND UNDERSTAND ALL WARNiNGS AND
iNSTRUCTiONS bEfORE USE.
Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
for technical questions or replacement parts, please call 1-800-444-3353.
Electrical Safety
1.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges,
and refrigerators. There is an increased risk of electric shock if your body is
grounded.
2.
3.
Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
Do not abuse the Charger’s power cord. Never use the Power Cord to carry
the Charger or pull the Plug from an outlet. Keep the Power Cord away from
heat, oil, sharp edges, or moving parts. Replace damaged Power Cords im-
mediately. Damaged Power Cords increase the risk of electric shock.
Personal Safety
1.
Stay alert. Watch what you are doing, and use common sense when operat-
ing a power tool. Do not use a power tool while tired or under the influence
of drugs, alcohol, or medication. A moment of inattention while operating power
tools may result in serious personal injury.
2.
3.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
Avoid accidental starting. be sure the Rotation button (6) is in the locked
position before inserting the battery. Carrying power tools with your finger on
the trigger, or inserting the Battery with the trigger depressed, invites accidents.
4.
5.
Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control of the power tool in unexpected situations.
Use safety equipment. Always wear eye protection. Dust mask, nonskid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions.
Always wear ANSI-approved safety goggles when working with this tool.
Tool Use and Care
1.
Use clamps (not included) or other practical ways to secure and support the
workpiece to a stable platform. Holding the work by hand or against your body
is unstable and may lead to loss of control.
2.
3.
Do not force the tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
Do not use the power tool if the trigger does not operate it. Any tool that cannot
be controlled with the trigger is dangerous and must be replaced.
SKU 96298
for technical questions, please call 1-800-444-3353.
PAGE 3
4.
Remove the battery from the tool and set the Rotation button (6) to the cen-
ter, locked position, before making any adjustments, changing accessories,
or storing the tool. These preventive safety measures reduce the risk of starting
the tool accidentally.
5.
6.
Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
Maintain the Cordless Driver with care. Keep screwdriver bits clean. Properly
maintained accessories with a clean edge are less likely to bind and are easier to
control. Do not use a damaged tool or accessory. Tag damaged tools “Do not use”
until repaired.
7.
8.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. if damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may become hazardous
when used on another tool.
Service
1.
2.
Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. follow instruc-
tions in this manual. Use of unauthorized parts or failure to follow maintenance
instructions may create a risk of electric shock or injury.
SPECifiC SAfETy RULES
1.
2.
Maintain a safe working environment. Keep the work area well lit. Make sure
there is adequate surrounding workspace. Always keep the work area free of ob-
structions, grease, oil, trash, and other debris. Do not use the Cordless Driver in
areas near flammable chemicals, dusts, and vapors. Do not use this product in a
damp or wet location.
Maintain labels and nameplates on the Cordless Driver. These carry important
information. If unreadable or missing, contact Harbor Freight Tools for a replace-
ment.
3.
4.
When using the Cordless Driver, always maintain a firm grip on the tool with
both hands.
Hold the tool by its insulated gripping surfaces when performing an opera-
tion where the Cordless Driver may contact hidden wiring. Contact with a
SKU 96298
for technical questions, please call 1-800-444-3353.
PAGE 4
“live” wire will make exposed metal parts of the Cordless Driver “live” and shock
the operator.
5.
6.
Do not use the Cordless Driver or Charger if it has been dropped, damaged,
left outdoors, or immersed in liquid.
To avoid electric shock, do not pull or carry the Charger by its Power Cord or
pull the Power Cord around sharp corners or edges. Do not unplug the Charger
by pulling on the Power Cord. Keep the Power Cord away from heated surfaces.
7.
To avoid electrical shock, do not handle the Charger, the Adapter, or the Cord-
less Driver with wet hands.
8.
Keep the Handles of the Cordless Driver dry, clean, and free from oil or
grease.
9.
Avoid unintentional starting. Make sure you are prepared to begin work before
turning on the Cordless Driver.
10.
Never leave the Charger unattended when it is plugged into an electrical outlet.
Unplug the Charger from its electrical outlet before leaving. Place the Charger on
a solid surface such as a garage floor; never place on anything flammable.
11.
12.
PROPER bATTERy PACK CARE: battery Pack (19) leakage may occur under
extreme usage or temperature conditions. If Battery Pack fluid comes in con-
tact with skin, rinse with lemon juice and vinegar then wash with soap and water.
If the fluid comes into contact with the eyes, flush with water for several minutes
and contact a doctor immediately. Never burn the Battery Pack, as it can explode
in a fire. Do not charge the Cordless Driver with a leaking Battery Pack. Contact
local solid waste authorities for instructions on correct disposal or recycling of the
Battery Pack.
WARNiNG! Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities, contain chemicals known (to the State of California) to
cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:lead from lead-based paints, crystalline silica from bricks and cement
or other masonry products, arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area,
and work with approved safety equipment, such as dust masks that are specially
designed to filter out microscopic particles. (California Health & Safety Code §
25249.5, et seq.)
13.
WARNiNG! People with pacemakers should consult their physician(s) before
using this product. Operation of electrical equipment in close proximity to a heart
pacemaker could cause interference or failure of the pacemaker.
SKU 96298
for technical questions, please call 1-800-444-3353.
PAGE 5
GROUNDiNG
WARNiNG!
improperly connecting the grounding wire can result in the risk of electric shock.
Check with a qualified electrician if you are in doubt as to whether the outlet is
properly grounded. Do not modify the power cord plug provided with the tool.
Never remove the grounding prong from the plug. Do not use the tool if the
power cord or plug is damaged. if damaged, have it repaired by a service facil-
ity before use. if the plug will not fit the outlet, have a proper outlet installed by
a qualified electrician.
GROUNDED TOOLS: TOOLS WiTH THREE PRONG PLUGS
1.
Tools marked with “Grounding Required” have a three wire cord and three prong
grounding plug. The plug must be connected to a properly grounded outlet. If
the tool should electrically malfunction or break down, grounding provides a low
resistance path to carry electricity away from the user, reducing the risk of electric
shock. (See figure A.)
2.
3.
The grounding prong in the plug is connected through the green wire inside the
cord to the grounding system in the tool. The green wire in the cord must be the
only wire connected to the tool’s grounding system and must never be attached to
an electrically “live” terminal. (See figure A.)
Your tool must be plugged into an appropriate outlet, properly installed and grounded
in accordance with all codes and ordinances. The plug and outlet should look like
those in the following illustration. (Se figure A.)
fiGURE A
fiGURE b.
DOUbLE iNSULATED TOOLS: TOOLS WiTH TWO PRONG PLUGS
1.
Tools marked “Double Insulated” do not require grounding. They have a special
double insulation system which satisfies OSHA requirements and complies with
the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard
Association, and the National Electrical Code. (See figure b.)
SKU 96298
for technical questions, please call 1-800-444-3353.
PAGE 6
2.
Double insulated tools may be used in either of the 120 volt outlets shown in the
preceding illustration. (See figure b.)
ExTENSiON CORDS
1.
2.
Grounded tools require a three wire extension cord. Double Insulated tools can
use either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge
extension cord. Using extension cords with inadequately sized wire causes a seri-
ous drop in voltage, resulting in loss of power and possible tool damage.
(See Chart A, next page.)
3.
The smaller the gauge number of the wire, the greater the capacity of the cord. For
example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
(See Chart A.)
4.
5.
When using more than one extension cord to make up the total length, make sure
each cord contains at least the minimum wire size required. (See Chart A.)
If you are using one extension cord for more than one tool, add the nameplate am-
peres and use the sum to determine the required minimum cord size.
(See Chart A.)
6.
7.
If you are using an extension cord outdoors, make sure it is marked with the suffix
“W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
Make sure your extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified electri-
cian before using it.
8.
Protect your extension cords from sharp objects, excessive heat, and damp or wet
areas.
SKU 96298
for technical questions, please call 1-800-444-3353.
PAGE 7
RECOMMENDED MiNiMUM WiRE GAUGE fOR ExTENSiON CORDS*
(120 OR 240 VOLT)
NAMEPLATE
AMPERES
(at full load)
ExTENSiON CORD LENGTH
25 feet
50 feet
75 feet 100 feet 150 feet
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
-
-
* based on limiting the line voltage drop to five volts at 150% of the rated amperes.
Chart A
SyMbOLOGy
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
V~
A
Amperes
No Load Revolutions per Minute (RPM)
n xxxx/min.
0
SKU 96298
for technical questions, please call 1-800-444-3353.
PAGE 8
UNPACKiNG
When unpacking, check to make sure that the product is complete and undamaged.
If any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
CHARGiNG (iNiTiAL CHARGE)
1.
The Battery Pack (19) requires charging before use. The recommended initial charge
time is twelve hours, prior to first use of the Cordless Driver.
Note: Always switch to a fresh battery when tool performance begins to diminish. Severe
heat is destructive to batteries; the more heat generated, the faster the battery will
lose power. A battery that gets too hot can be permanently damaged. Never over-
discharge a battery by using the tool after performance decreases. Never attempt to
discharge a battery by continuing to pull the trigger. When tool performance begins
to diminish, stop the tool, recharge the battery, and use a fully charged battery for
optimal performance.
2.
When the Battery Pack-after the initial charge-requires recharging it must charge
for five to seven hours in order to operate at full power.
3.
4.
Charging room temperature: 50° F. – 104° F.
Depress both buttons at the rear of the Battery Pack and slide the unit down to
detach from the Driver.
5.
6.
7.
Insert the Battery Pack (19) into the Charger (24) (the Battery Pack can only fit into
the Charger in one position), plug Charger
into Adapter (25), and plug Adapter into any
standard electrical outlet.
battery
Pack (19)
While charging, the Battery Pack, Charger,
and Adapter may become warm to the touch.
This is normal, and does not indicate a prob-
lem.
Adapter
(25)
When the Battery Pack is in the Charger,
both the red and green lights on the Charger
will be illuminated while charging, when the
Battery Pack is fully charged the red light
will turn off, indicating that the Battery Pack
is ready for use. Once the Battery Pack is
fully charged, unplug the Charger from the
Charger
(24)
electrical outlet, unplug the Charger from the electrical outlet and remove the Bat-
tery Pack from the Adapter.
SKU 96298
for technical questions, please call 1-800-444-3353.
PAGE 9
OPERATiNG iNSTRUCTiONS
NOTE: For additional information regarding the parts listed in the following pages, refer to
the Parts List & Assembly Diagram.
WARNiNG! Remove the Battery Pack (19) from the tool and set the Rotation Button
(6) to its center, locked, position before making any adjustments, changing acces-
sories, or storing the tool.
Gear box with
Torque Ring (2)
Chuck (1)
Rotation button (6)
Trigger (12)
battery Pack
(19)
1.
2.
To install a screwdriver bit, insert the correct Bit (26) for the application into the
magnetic Bit Adapter (27). Never insert one of the included bits (26) directly
into the Chuck. A smaller gauge than 1/4”will not be firmly secured and may
result in injury or property damage. With the Chuck (1) pointing away from you,
pull gently on the Chuck sleeve and insert the Bit Adapter into the Chuck. Release
the Chuck sleeve and the Bit Adapter will lock firmly in place. The Chuck accepts
1/4” Hex Shank only. To remove the Bit Adapter (27), reverse the above-mentioned
procedure.
Secure the workpiece in place, using a vise or clamps (not included).
Note: Never change Torque Setting while the Cordless Driver is still rotating, as this can
damage the Cordless Driver.
3.
Selecting an appropriate torque setting (1-24):
SKU 96298
for technical questions, please call 1-800-444-3353.
PAGE 10
The different sizes of screws pictured on the Torque Ring are an indication of how
much torque the Cordless Driver will apply to the bit before the clutch slips, allowing
the bit to stop and helping to prevent damage to the screw, bit, or workpiece. The
larger the screw, the more torque is applied before the clutch slips. Always start
with a lower torque to help prevent damage. This Cordless Driver also has torque
settings between the screw markings to allow a greater range of selection.
4.
5.
6.
Set the driving torque by turning the Gear Box with Torque Ring (2) so that it lines
up with the Arrow on the center top of the Cordless Driver.
When driving in light gauge metal or wood, use a wooden block to back up the
material and prevent damage to the workpiece.
Mark the center of the hole for the screw with a center punch (not included) to give
a Bit a start and to prevent it from “walking”.
7.
8.
Insert the fully charged Battery Pack (19) into the handle of the Cordless Driver.
The Rotation Button (6) allows you to change the rotational direction of the Cord-
less Driver. For a clockwise rotation, move the Rotation Button to the right. For a
counterclockwise rotation, move the Rotation Button to the left. The center position
locks the Trigger (12) to prevent the Cordless Driver from operating.
9.
Hold the Cordless Driver firmly with both hands, as torque from the Motor can cause
the tool to twist.
10.
11.
Operate the Driver by squeezing the Trigger (12). The speed can be controlled by
varying the pressure on the Trigger.
If the clutch starts slipping before the screw is in all the way, stop the driver, put the
Rotation Button (6) in the center position and change the torque setting. Reset the
rotation direction before continuing.
14.
Release the Trigger (12) to stop the Driver, put the Rotation Button in the center
position, and remove the bit from the Bit Adapter.
iNSPECTiON, MAiNTENANCE, AND CLEANiNG
1.
2.
WARNiNG! Remove the battery Pack (19) from the tool and set the Rota-
tion button (6) to the center,locked,position before performing any inspection,
maintenance, or cleaning.
bEfORE EACH USE, inspect the general condition of the Cordless Driver. Check
for misalignment or binding of moving parts, cracked or broken parts, leaking Bat-
tery Pack, damaged Charger wiring, chipped or broken Bits, and any other condition
that may affect its safe operation. If abnormal noise or vibration occurs, have the
problem corrected before further use.
Do not use damaged equipment.
SKU 96298
for technical questions, please call 1-800-444-3353.
PAGE 11
3.
4.
After each use: With a soft brush or cloth remove all dirt and debris from the Cord-
less Driver. Do not immerse the Cordless Driver in any liquids.
When the battery needs to be replaced remember that the lithium battery in
this tool must be recycled or disposed of properly.
SKU 96298
for technical questions, please call 1-800-444-3353.
PAGE 12
PARTS LiST
Part
Description
Qty
Part
Description
Qty
1
Chuck
1
1
7
1
4
1
1
1
1
1
1
1
1
1
15
Black Wire
1
1
1
2
1
1
1
1
9
1
1
9
2
Gear box with Torque Ring
Screw
16
17
18
19
20
21
22
23
24
25
26
Red Wire
3
Bracket
4
Right Body
Screw
Contact Plate
Battery Pack
Ring
5
6
Rotation Button
Clear Soft Grip
Right Plate
Tube
7
Steel Wire Ring
Compress Spring
Steel Ball
8
9
10
11
12
13
14
Black Wire
Red Wire
Charger
Adapter
Trigger
Screwdriver Bits (in rubber
sleeve)
Left Plate
27
Bit Adapter
1
Left Body
ASSEMbLy DiAGRAM
27
26
25
24
SKU 96298
for technical questions, please call 1-800-444-3353.
PAGE 13
PLEASE READ THE fOLLOWiNG CAREfULLy
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN
THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE
IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE-
MENT PARTS THERETO.
LiMiTED 90 DAy WARRANTy
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this product
is free from defects in materials and workmanship for the period of 90 days from the date
of purchase. This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,
improper installation, normal wear and tear, or to lack of maintenance.We shall in no event
be liable for death, injuries to persons or property, or for incidental, contingent, special
or consequential damages arising from the use of our product. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation
of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
plaint must accompany the merchandise. If our inspection verifies the defect, we will either
repair or replace the product at our election or we may elect to refund the purchase price
if we cannot readily and quickly provide you with a replacement. We will return repaired
products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning
the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts.
SKU 96298
for technical questions, please call 1-800-444-3353.
PAGE 14
|