Chauvet Home Safety Product 200B User Manual

Snapshot  
LEDsplash™ 200B  
LEDPAR200B  
Use on Dimmer  
Outdoor Use  
Sound Activated  
DMX  
Master/Slave  
Auto-ranging  
Power Supply  
Replaceable Fuse  
User Serviceable  
Duty Cycle  
User Manual  
CHAUVET, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A  
(800) 762-1084 (954) 929-1115  
FAX (954) 929-5560  
2010-03-09/15:03  
 
1. BEFORE YOU BEGIN  
What is included  
1 x LED-PAR200B  
1 x Warranty Card  
1 x Users Manual  
Unpacking Instructions  
Immediately upon receiving a product, carefully unpack the carton, check the contents to ensure that  
all parts are present, and have been received in good condition. Notify the shipper immediately and  
retain packing material for inspection if any parts appear damaged from shipping or the carton itself  
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture  
must be returned to the factory, it is important that the fixture be returned in the original factory box  
and packing.  
AC Power  
To determine the power requirements for a particular product, see the label affixed to the back plate  
of the product or refer to the product’s specifications chart. A product’s listed current rating is its  
average current draw under normal conditions. All fixtures must be powered directly off a switched  
circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or  
dimmer channel is used solely for a 0% to 100% switch. Before applying power, check that the source  
voltage matches the product’s requirement. Check the product or device carefully to make sure that if  
a voltage selection switch exists that it is set to the correct line voltage you will use.  
Warning!  
All fixtures must be connected to circuits with a suitable Earth Ground.  
Safety Instructions  
Please read these instructions carefully, which includes important  
information about the installation, usage and maintenance.  
Please keep this User Guide for future consultation. If  
Maximum ambient temperature is Ta: 40° C. Do not  
you sell the unit to another user, be sure that they  
operate fixture at temperatures higher than this.  
also receive this instruction booklet.  
In the event of serious operating problem, stop using  
the unit immediately. Never try to repair the unit by  
yourself. Repairs carried out by unskilled people can  
lead to damage or malfunction. Please contact the  
nearest authorized technical assistance center.  
Always make sure that you are connecting to the  
proper voltage and that the line voltage you are  
connecting to is not higher than that stated on decal  
or rear panel of the fixture.  
This product is intended for indoor use only! To  
prevent risk of fire or shock, do not expose fixture to  
rain or moisture.  
Don’t connect the device to a dimmer pack.  
Make sure power cord is never crimped or damaged.  
Never disconnect power cord by pulling or tugging on  
the cord.  
Make sure there are no flammable materials close to  
the unit while operating.  
Avoid direct eye exposure to lamp while it is on.  
Always disconnect from power source before  
servicing or replacing lamp or fuse and be sure to  
replace with same lamp source.  
The unit must be installed in a location with adequate  
ventilation, at least 50 cm from adjacent surfaces. Be  
sure that no ventilation slots are blocked.  
Secure fixture to fastening device using a safety  
chain.  
Caution!  
There are no user serviceable parts inside the unit. Do not open the housing or attempt any  
repairs yourself. In the unlikely event your unit may require service, please contact  
CHAUVET®.  
LED-PAR200B User Manual  
3
2010-03-09/15:03  
 
2. INTRODUCTION  
Features  
6-channel DMX-512 LED wash light  
Blackout/static/dimmer/strobe  
Selector switch for sound active or automatic programs  
Static colors and RGB color mixing with or without DMX controller  
Built-in automated programs via master/slave or DMX  
Built-in sound activated programs via master/slave or DMX  
Additional Features  
Compatible with CHAUVET® Satellite™ system  
DMX Channel Values  
DMX  
1
2
3
4
5
6
CHANNEL  
(COLUMNS)  
Red  
000~255  
Green  
000~255  
Blue  
000~255  
000~020 No Strobe  
021~255 Strobe  
RGB  
000~029  
030~199  
(Slow>Fast)  
Strobe  
000~255  
Pulse  
No Function  
Color Macro  
000~255  
Color Macros  
120~149  
No Function  
Dimmer  
000~255  
Chase Speed  
000~255 (slow~fast)  
RGB Chase  
150~179  
180~209  
210~239  
240~255  
100%~0%  
No Function No Function  
Color Change  
No Function  
Program Speed  
000~255 (slow~fast)  
Color Change  
w/ fade  
Sound  
No Function  
CONTROL MODES & OPTIONS  
(Rows)  
For a detailed view of DMX values turn to the Appendix section in this manual. Control mode parameters are set by DMX  
values in Channel # 1.  
LED-PAR200B User Manual  
4
2010-03-09/15:03  
 
Product Overview  
Satellite™  
connection  
Power Input  
(Hardwired cable)  
Safety  
attachment  
point  
Power LED  
Indicator  
Microphone Sensitivity  
Adjustment Knob  
Fuseholder  
DMX, Master/Slave  
Signal LED Indicator  
Bracket  
Adjustment  
Knob  
Standalone  
Auto/Sound Selection  
Switch  
DIP Switches  
DMX Out  
DMX In  
Bracket  
Adjustment  
Knob  
LED-PAR200B User Manual  
5
2010-03-09/15:03  
 
Introduction  
3. SETUP  
Power  
Warning!  
All fixtures must be connected to circuits with a suitable Earth Ground.  
To determine the power requirements for a particular fixture, see the label affixed to the back plate  
of the fixture or refer to the fixture’s specifications chart.  
A fixture’s listed current rating is its average current draw under normal conditions.  
All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat  
(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0%  
to 100% switch.  
Before applying power to a fixture, check that the source voltage matches the fixture’s  
requirement.  
Power Cable Configuration  
CABLE  
BLACK  
PIN  
Live  
INTERNATIONAL  
L
N
WHITE  
Neutral  
Earth  
YELLOW/GREEN  
EG (Ground)  
Mounting  
Orientation  
Hanging Clamp  
This fixture can be mounted on a truss using a clamp in any  
position.  
Rigging  
The fixture includes a mounting yoke to which 1 rigging clamp can be  
bolted.  
The hole is 13 mm in diameter.  
1. Align the clamp screw with the center hole on the yoke and tighten.  
2. Verify the structure can hold 10 times the weight of all to-be installed fixtures.  
3. Adjust the angle on the yoke arm as necessary.  
LED-PAR200B User Manual  
6
2010-03-09/15:03  
 
4. OPERATING INSTRUCTIONS  
The LEDsplash™ 200B is a DMX controllable, full RGB color mix par can made up of highly efficient  
and super bright LEDs. All red, green and blue LEDs can be controlled separately allowing the  
creation of an unlimited range of colors.  
The LEDsplash™ 200B can operate in Stand-Alone, Master/Slave and via DMX-512 control utilizing  
six DMX channels.  
Master/Slave Mode  
This mode allows a single unit to run to the beat of the music, or the unit will auto change in Auto  
Mode.  
1) Set dipswitches position to Sound Active or Auto Mode.  
Mode  
Dipswitches  
Sound Active  
Auto Mode  
1~10 = Off, switch set to Music  
1~10 = Off, switch set to Auto  
2) The unit will react to the low frequencies of music via the internal microphone in Sound Active  
mode, or the unit will auto change in Auto Mode.  
3) Use the audio sensitivity knob on the back of the unit to make the unit more or less sensitive in  
Sound-Active mode. Turning the knob counterclockwise decreases the sensitivity; turning the  
knob clockwise increases the sensitivity.  
Daisy Chain Connection  
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector  
of the first fixture.  
2. Connect the end of the cable coming from the first fixture which will have a (female) 3-pin  
connector to the input connector of the next fixture consisting of a (male) 3-pin connector. Then,  
proceed to connect from the output as stated above to the input of the following fixture and so on.  
DIP Switch Options  
FUNCTIONS  
DIP SWITCHES ( ON )  
NOTES & DESCRIPTION  
Music/Auto switch  
Color change program  
(Auto/Music)  
Music: Sound-Activated, sound adjustment knob sets  
sensitivity  
None  
Auto: sound adjustment know sets speed of program  
1
2
3
4
5
6
7
8
9
Low Intensity  
Medium Intensity  
Full Intensity  
Red LEDs  
Green LEDs  
Blue LEDs  
Low Intensity  
Medium Intensity  
Full Intensity  
Low Intensity  
Medium Intensity  
Full Intensity  
LED-PAR200B User Manual  
7
2010-03-09/15:03  
 
Appendix  
DMX Control Mode  
Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to  
customizing or creating a show. In this mode you will be able to control each individual trait of the  
fixture and each fixture independently. The LEDsplash™ 200B uses six channels of control.  
1. A working DMX signal source plugged into the LEDsplash™ 200B activates the DMX mode.  
Setting the DMX address  
This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start  
address" from 1 to 511. A fixture requiring one or more channels for control begins to read the data  
on the channel indicated by the start address. For example, a fixture that occupies or uses 6 channels  
of DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101,  
102, 103, 104, and 105. Choose start addresses so that the channels used do not overlap and notate  
the start address selected for future reference.  
If this is your first time addressing a fixture using the DMX-512 control protocol than I suggest jumping  
to the Appendix Section and read the heading “DMX Primer”. It contains very useful information that  
will help you understand its use.  
Set the start address using the group of DIP switches located usually on bottom of the fixture. Each  
dip switch has an associated value. Adding the value of each switch in the ON position will provide  
the start address. Determining which switches to toggle ON given a specific start address can be  
accomplished in the following manner. By subtracting the largest switch value possible from the  
selected start address until zero is achieved.  
EXAMPLE STARTING ADDRESS  
Address 10  
ON  
Pin # 4 = 8  
Pin # 2 = 2  
Total  
= 10  
1
2
3
4
5
6
7
8
9 10  
Address 24  
Pin # 5 = 16  
Pin # 4 = 8  
ON  
Total  
= 24  
1
2
3
4
5
6
7
8
9 10  
233 (128) = 105, Turn ON DIP # 8  
105 (64) = 41, Turn ON DIP # 7  
41 (32) = 9, Turn ON DIP # 6  
9 (8) = 1, Turn ON DIP # 4  
DIP SWITCH  
(DMX VALUE)  
1
2
1
2
Resolving address using  
simple math.  
1 (1) = 0, Turn ON DIP # 1  
3
4
4
5
6
7
8
9
8
You will most likely use the first  
available number which may be  
number 1. This number was  
selected for example purposes.  
16  
32  
64  
128  
256  
Address 233  
10  
LED-PAR200B User Manual  
8
2010-03-09/15:03  
 
Appendix  
5. APPENDIX  
DMX Primer  
There are 512 channels in a DMX connection. Channels may be assigned in any manner. A fixture  
capable of receiving DMX-512 will require one or a number of sequential channels. The user must  
assign a starting address on the fixture that indicates the first channel reserved in the controller.  
There are many different types of DMX controllable fixtures and they all may vary in the total number  
of channels required. Choosing a start address should be planned in advance. Channels should  
never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is  
set incorrectly. You can however, control multiple fixtures of the same type using the same starting  
address as long as the intended result is that of unison movement or operation. In other words, the  
fixtures will be slaved together and all respond exactly the same.  
DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is  
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which  
the fixtures are connected is not important and has no effect on how a controller communicates to  
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures  
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The  
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+).  
Fixture Linking  
DMX connector configuration  
Resistance 120  
ohm ¼ W between  
pin 2 (DMX -) and  
pin 3 (DMX +) of  
the last fixture.  
1
3
2
COMMON  
1
1
3
DMX +  
DMX -  
INPUT  
3
OUTPUT  
Termination reduces signal errors and to  
avoid signal transmission problems and  
interference, it is always advisable to  
connect a DMX signal terminator.  
2
2
Note!  
If you use a controller with a 5-pin DMX output connector, you will need to use a  
5-pin to 3-pin adapter.  
The chart below details a proper cable conversion:  
3-PIN TO 5-PIN CONVERSION CHART  
Conductor  
3-Pin Female (output)  
5-Pin Male (Input)  
Pin 1  
Pin 1  
Ground/Shield  
Data ( - )signal  
Pin 2  
Pin 3  
Pin 2  
Pin 3  
Pin 4  
Pin 5  
Data ( + ) signal  
Not Used  
Not Used  
LED-PAR200B User Manual  
9
2010-03-09/15:03  
 
Appendix  
DMX Channel Values  
NOTE! Please read all instructions carefully on fixture DMX control mode and addressing.  
DMX channels 2, 3, 4, 5 and 6 functions are determined by the current settings of channel 1. For  
example, while Channel 1 is set between 000 and 029 the following conditions will apply;  
.
.
.
.
.
Channel 2 will control the Red LEDs  
Channel 3 will control the Green LEDs  
Channel 4 will control the Blue LEDs  
Channel 5 will control Strobing  
Channel 6 will control the Dimmer  
CHANNEL  
VALUE  
FUNCTION  
CH 2  
CH 3  
CH 4  
Blue  
CH 5  
CH 6  
Strobe  
000 020 No Strobe  
021 255 SlowFast  
Red  
000 255  
Green  
000 255 000 255  
000 029 RGB Control Mode  
Pulse Strobe  
No  
Function  
030 059 Pulse ( 0 <-> 100% )  
060 089 Pulse ( 100 <-> 0% )  
090 119 Pulse ( 100 <->0% <->100)  
Speed  
000 255  
Color Macro  
120 149 Color Macros  
No  
Function  
See Table 1.1  
Dimmer  
000 255  
1
R,G,B Chase  
150 179 RGB Chase pattern  
No  
Function  
No  
Function  
Automatic  
Speed  
180 209 Color change  
000 255  
No  
Function  
Automatic (Fade)  
210 239 Color Change w fade  
Sound Activated  
240 255 Music/Auto switch must be set  
to music  
No  
Function  
Table 1.1  
MODE  
CH 2  
DESCRIPTION  
000 016 Red  
017 056 Red ( Full )  
Music/Auto Switch  
Note! Regardless of DMX controller  
operated use, when the  
Green: ( 0% ~ 100% )  
057 094 Green (Full  
LED-PAR200B is set to run in Sound  
Activated mode, you should make  
sure that all units are properly  
switched to Music and that you have  
adjusted the rotary dial to optimize the  
sound level response of the unit.  
Red: ( 100% ~ 0% )  
095 096 Green  
097 136 Green ( Full )  
Color  
Macro  
Blue: ( 0% ~ 100% )  
Ch 1  
120 149  
SWITCH  
AUTO  
ROTARY FUNCTION  
137 174 Blue ( Full )  
Green: ( 100% ~ 0% )  
Adjusts speed of built in  
program  
175 176 Blue  
177 216 Blue ( Full )  
Adjusts sound sensitivity of  
built in microphone.  
MUSIC  
Red: ( 0% ~ 100% )  
217 255 Blue ( Full )  
Red ( Full )  
Green: ( 0% ~ 100% )  
LED-PAR200B User Manual  
10  
2010-03-09/15:03  
 
Appendix  
Returns Procedure  
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.  
Package must be clearly labeled with a Return Merchandise Authorization Number (RMA #).  
Products returned without an RMA # will be refused. Call CHAUVET® and request RMA # prior to  
shipping the fixture. Be prepared to provide the model number, serial number and a brief description  
of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from  
inadequate packaging is the customer’s responsibility. CHAUVET® reserves the right to use its own  
discretion to repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is  
always a safe method to use.  
Claims  
Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be  
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and  
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim  
for items such as missing component/part, damage not related to shipping, and concealed damage,  
must be made within seven (7) days of receiving merchandise.  
LED-PAR200B User Manual  
11  
2010-03-09/15:03  
 
DMX DIP Switch Quick Reference Chart  
DMX Address Quick Reference Chart  
DIP Switch Position  
DMX DIP SWITCH SET #9  
0
0
0
0
0
0
0
0
0
1
0
1
0
1
0
1
1
0
1
0
1
0
1
0
1
1
1
1
1
1
1
1
0=OFF  
1=ON  
#8  
#7  
#6  
0
0
0
1
1
0
1
1
0
0
0
1
1
0
1
1
0
0
0
1
1
0
1
1
0
0
0
1
1
0
1
1
X=OFF or ON  
#1 #2 #3 #4 #5  
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
32 64  
33 65  
34 66  
35 67  
96  
97  
98  
99  
128  
129  
130  
131  
132  
133  
134  
135  
136  
137  
138  
139  
140  
141  
142  
143  
144  
145  
146  
147  
148  
149  
150  
151  
152  
153  
154  
155  
156  
157  
158  
159  
160  
161  
162  
163  
164  
165  
166  
167  
168  
169  
170  
171  
172  
173  
174  
175  
176  
177  
178  
179  
180  
181  
182  
183  
184  
185  
186  
187  
188  
189  
190  
191  
192  
193  
194  
195  
196  
197  
198  
199  
200  
201  
202  
203  
204  
205  
206  
207  
208  
209  
210  
211  
212  
213  
214  
215  
216  
217  
218  
219  
220  
221  
222  
223  
224  
225  
226  
227  
228  
229  
230  
231  
232  
233  
234  
235  
236  
237  
238  
239  
240  
241  
242  
243  
244  
245  
246  
247  
248  
249  
250  
251  
252  
253  
254  
255  
256  
257  
258  
259  
260  
261  
262  
263  
264  
265  
266  
267  
268  
269  
270  
271  
272  
273  
274  
275  
276  
277  
278  
279  
280  
281  
282  
283  
284  
285  
286  
287  
288  
289  
290  
291  
292  
293  
294  
295  
296  
297  
298  
299  
300  
301  
302  
303  
304  
305  
306  
307  
308  
309  
310  
311  
312  
313  
314  
315  
316  
317  
318  
319  
320  
321  
322  
323  
324  
325  
326  
327  
328  
329  
330  
331  
332  
333  
334  
335  
336  
337  
338  
339  
340  
341  
342  
343  
344  
345  
346  
347  
348  
349  
350  
351  
352  
353  
354  
355  
356  
357  
358  
359  
360  
361  
362  
363  
364  
365  
366  
367  
368  
369  
370  
371  
372  
373  
374  
375  
376  
377  
378  
379  
380  
381  
382  
383  
384  
385  
386  
387  
388  
389  
390  
391  
392  
393  
394  
395  
396  
397  
398  
399  
400  
401  
402  
403  
404  
405  
406  
407  
408  
409  
410  
411  
412  
413  
414  
415  
416  
417  
418  
419  
420  
421  
422  
423  
424  
425  
426  
427  
428  
429  
430  
431  
432  
433  
434  
435  
436  
437  
438  
439  
440  
441  
442  
443  
444  
445  
446  
447  
448  
449  
450  
451  
452  
453  
454  
455  
456  
457  
458  
459  
460  
461  
462  
463  
464  
465  
466  
467  
468  
469  
470  
471  
472  
473  
474  
475  
476  
477  
478  
479  
480  
481  
482  
483  
484  
485  
486  
487  
488  
489  
490  
491  
492  
493  
494  
495  
496  
497  
498  
499  
500  
501  
502  
503  
504  
505  
506  
507  
508  
509  
510  
511  
1
2
3
4
5
6
7
8
9
36 68 100  
37 69 101  
38 70 102  
39 71 103  
40 72 104  
41 73 105  
10 42 74 106  
11 43 75 107  
12 44 76 108  
13 45 77 109  
14 46 78 110  
15 47 79 111  
16 48 80 112  
17 49 81 113  
18 50 82 114  
19 51 83 115  
20 52 84 116  
21 53 85 117  
22 54 86 118  
23 55 87 119  
24 56 88 120  
25 57 89 121  
26 58 90 122  
27 59 91 123  
28 60 92 124  
29 61 93 125  
30 62 94 126  
31 63 95 127  
DIP Switch Position  
DMX Address  
LED-PAR200B User Manual  
12  
2010-03-09/15:03  
 
Appendix  
Technical Specifications  
WEIGHT & DIMENSIONS  
Length..........................................................................................................................132 mm (5.2 in)  
Width............................................................................................................................249 mm (9.8 in)  
Height ..........................................................................................................................236 mm (9.3 in)  
Weight........................................................................................................................... 2.1 kg (4.7 lbs)  
POWER  
Auto-ranging Power Supply.............................................................................100~240 VAC, 50/60 Hz  
Power Consumption @ 120 VAC, 60 Hz ...............................................20 W (0.3 A) max, 0.2 A inrush  
Power Consumption @ 230 VAC, 50 Hz ...............................................21 W (0.1 A) max, 0.2 A inrush  
Fuse............................................................................................................................... F 1.6 A, 250 V  
LIGHT SOURCE  
LED....................................................................... 199 Total (Red 67, Green 66, Blue 66) 100,000 hrs  
PHOTO OPTIC  
Beam Angle .................................................................................................................................... 28°  
Field Angle...................................................................................................................................... 49°  
Luminance @ 1 m..................................................................................................................... 930 lux  
FUSE  
Main..................................................................................................... 20 mm, Glass 1.6 A, Fast Blow  
SATELLITE OPERATION  
Run time @ 100% output (full RGB)..............................................................................................4 hrs  
Maximum Run Time (auto program or single color)............................................................. Up to 8 hrs  
Connection............................................................................................................ 4-pin DIN connector  
CONTROL & PROGRAMMING  
Data input ............................................................................................. locking 3-pin XLR male socket  
Data output ........................................................................................ locking 3-pin XLR female socket  
Data pin configuration ............................................................................pin 1 shield, pin 2 (-), pin 3 (+)  
Protocols.....................................................................................................................DMX-512 USITT  
DMX Channels....................................................................................................................................6  
ORDERING INFORMATION  
LEDsplash™ 200B......................................................................................................... LEDPAR200B  
WARRANTY INFORMATION  
Warranty ........................................................................................................... 2-year limited warranty  
Technical Support  
Address: Service Dept.  
3000 N 29th Ct, Hollywood, FL 33020 (U.S.A.)  
Support (Email): [email protected]  
Telephone: (954) 929-1115 - (Press 4)  
Fax: (954) 929-5560 - (Attention: Service)  
LED-PAR200B User Manual  
13  
2010-03-09/15:03  
 

Billy Goat Lawn Mower CR550HCV User Manual
Black Decker Blender FP1550SDC User Manual
Bolens Lawn Mower 620 thru 669 User Manual
Bosch Appliances Oven WALL OVENS User Manual
Breville Coffeemaker BES870 User Manual
Broil King Gas Grill CG 10B User Manual
Caframo Fan 14078 806GS BBX User Manual
Cannon Copier CLC 4000 User Manual
Century Cooktop HES80 User Manual
Char Broil Charcoal Grill 463720110 User Manual