Casio Switch SD208PRF User Manual

STEP 2 Maneuver the Switch to insert the screws into the two slots, then slide  
Back Panel  
Placement Options  
the switch downward onto the screws.  
Product Overview  
The Ethernet network ports are located on the back panel of the Switch. All  
ports are auto-negotiating and have automatic MDI/MDI-X crossover detection.  
Set the Switch on its four rubber feet, or mount the Switch on a wall.  
Before mounting the switch onto a wall, it is important to consider the following:  
Quick Start Guide  
1
Thank you for choosing the SD208P 8-Port 10/100 Mbps switch. It is compliant  
with most popular network standards, and migrates Ethernet and Fast Ethernet  
networks seamlessly. It is equipped with 8 auto-negotiating 10/100 Mbps  
ports, capable of identifying and determining the best transmission speed to  
build the connection.  
Ensure the wall is strong enough to support the switch, a minimum of 1/2” of  
sheet rock is recommended.  
Do not operate the switch in an area that has reduced air flow, or exceeds  
an ambient temperature of 104 degrees (40 C).  
The switch can be mounted either horizontal or vertical.  
The SD208P supports IEEE 802.3af Power over Ethernet on ports 1 through 4  
with a total power budget of 32 Watts. This provides power over Cat-5 cabling  
to PoE end devices such as wireless access points, IP phones or other PoE  
powered devices to help eliminate the need for dedicated electrical outlets.  
Furthermore, auto MDI/MDI-X on each port makes your network configuration  
easier than ever.  
Ethernet Ports—Ports 1-4 are high priority PoE ports with a total power budget  
of 32 watts. Ports 5-8 are low priority ports without PoE. The priority ratio of  
ports 1-4 to ports 5-8 is 4:1.  
Mounting screws should have a head 5.5mm wide, 2mm deep, and the shaft  
of the screw should be at least 13mm long and 2.9mm wide.  
To use the wall-mount option, follow these instructions:  
Power—Port for an external power adapter with 48V/1.25A DC output that  
supports 100/240 V and 50/60 Hz inputs.  
STEP 1 The wall-mount slots are two crisscross slots on the Switch’s  
The SD208P has a built in feature to aid network performance at times of  
excessive load called Port Priority. This feature integrates Port Based QoS on  
all 8 ports to meet different service requirements on voice, video and data  
transformation. This feature can be useful during excessive loads, for example,  
when one type of traffic may require priority over another.  
bottom panel. Attach two screws to the wall 64mm apart.  
Side Panels  
There is a physical security slot located on the side of the Switch. The security  
slot is where you can attach a lock to protect the Switch from theft.  
Front Panel  
The LEDs are located on the front panel of the Switch.  
Cisco Small Business  
Model SD208P  
8-Port 10/100 Unmanaged Switch with PoE  
Package Contents  
SD208P Switch  
Power Adapter  
Quick Start Guide  
Power—(Green) This LED lights up and remains lit when the Switch is powered  
on.  
Link/ACT (1-8)—(Green) One LED per port, lights up when a connection is made  
(Link up) through the corresponding port. The LED will flash when there is  
activity (Tx or Rx) on the corresponding port.  
PoE Status (1-4) (Green) These LEDs light up and remain lit when the switch is  
providing PoE power on the port (only for ports 1-4).  
PoE Max (Yellow) This LED lights up and remains lit when the switch is providing  
more than 80% maximum PoE power (when the total power supplied reaches  
the 25.6 W level across ports 1-4)  
 

Black Box Computer Accessories 26542 User Manual
Black Box Dishwasher CMA DISHMACHINE User Manual
Black Box Switch KV2116E User Manual
Black Decker Coffeemaker DCM680BF User Manual
Blanco Indoor Furnishings 157 149 User Manual
BOXLIGHT Projector MP 350m User Manual
Briggs Stratton Automobile Parts 20M114 0138 E1 User Manual
Calphalon Coffeemaker HE100CMT User Manual
Cannon Camcorder PIXMA MX532 User Manual
Casio Watch MA0707 EA User Manual