LP-1
Laser Pointer
Wireless Presentation
Trackball Mouse
Owner’s Manual
califone.com
Specifications/Features
• Transmission Frequency: 2.4GHz
• Trackball mouse
• Laser pointer function
• Sleeping mode current: 22uA
• Usage time: 40-45 days (average usage, full charge)
• Charging time: 6-8 hours
• Operating range: 30’(from receiver)
• 4 buttons (2 mouse buttons + 2 fwd/back buttons)
• Lanyard on pointer/mouse for wearing around neck
• 28”retractable USB cable for recharging
• Case Material: Rubberized ABS
• Supply voltage: 3V (batteries) / 5VDC (USB)
• Regulatory: CE, FCC
• Dimensions (pointer): 1.25”x 2”x 4”
• Weight: 53.2g (pointer w/o batteries) + 5g (receiver)
• Max operating current: 22mA
System Compatibility
Windows XP/95/98/ME/2000/NT4.0 (on older operating systems, USB drivers must be pre-installed)
Setup & Operation:
1. Put the batteries into the laser pointer and connect the laser pointer to your computer using the provided USB cable.
The laser pointer should automatically charge the batteries. Please allow 8 hours charging time before using the pointer.
2. After charging, you may disconnect the pointer from the computer. Then plug the USB receiver into your computer.
3. After a short period of time (~1minute) your computer should automatically recognize the new device and it
should be ready to operate.
4. The pointer/mouse has a three-position switch. The left position is“Off”. The middle position“Pointer”is to operate the
laser pointer only (the mouse will not function in this mode). The right position“Mouse”enables all of the functions
(mouse, buttons, laser pointer).
5. The mouse should work out-of-the-box, but if the mouse and button functions do not operate, you may need to match
the mouse/pointer to the USB receiver. To do so, follow these steps:
• Make sure the receiver is connected to the PC and is recognized properly by your computer.
• Press the button on the receiver. The LED on the receiver should begin to flash
• Then, on the mouse move the switch to the middle or right, position and click the Code Matching
button at the back of the unit.
• When the LED on the receiver stops flashing, the units should be properly set up.
When in Pointer mode and Microsoft Powerpoint is the active application on the
computer, the buttons function as follows:
• Previous Slide (lower left button)
• Next Slide (lower right button)
• Pause Presentation (go to blank screen momentarily ; press again to go back to presentation) ( upper left button)
• Exit Presentation (double click to exit) ( upper right button)
When in Mouse mode, the buttons function as follows:
• Mouse Left Click (lower left button)
• Mouse Right Click (lower right button)
• Backward (upper left button) – Can be used in applications and Windows folders.
• Forward (upper right button) – Can be used in applications and Windows folders.
2
CAUTION
RISK OF ELECTRIC SHOCK - DO NOT OPEN
!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR
BACK. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QAULIFIED
PERSONNEL.
The exclamation point within a
The lightening flash with arrowhead
triangle is intended to tell the user
within a triangle is intended to tell the
that important operating and servicing
user that parts inside the product are a
risk of electric shock to persons.
instructions are in the papers with
!
the appliance.
This product is not designed to
function normally in strong electro-
magnetic fields. Consequently, the
Ce produit n’est pas conçu pour
un fonctionnement dans de forts
champs électromagnétiques. Par
conséquent, la qualité sonore peut
diminuer si ce produit est exposé à
WARNING:
TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK, SO
NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
audio quality may degrade while the
product is exposed to strong electromagnetic fields.
Normal audio quality operation will be recovered
when the strong electromagnetic field is no
longer present.
un fort champ életromagnétique. La qualité sonore
redeviendra normale après affaib-lissement du
champ électromagnétique.
IMPORTANT SAFETY INSTRUCTIONS
POWER CORD PROTECTION - POWER SUPPLY CORDS
ATTENTION: ALL SAFETY AND OPERATING INSTRUCTIONS
SHOULD BE READ BEFORE OPERATING APPLIANCE. ALL OPER-
ATING AND USE INSTRUCTIONS SHOULD BE FOLLOW-
ED WHEN OPERATING THE APPLIANCE. HEED AND ADHERE
TO ALL WARNINGS ON THE APPLIANCE AND IN THE OPERATING
INSTRUCTIONS. RETAIN ALL SAFETY AND OPERATING INSTRUC-
TIONS FOR FUTURE REFERENCE.
SHOULD BE ROUTED SO THAT THEY ARE NOT LIKELY TO BE
WALKED ON OR PINCHED BY ITEMS PLACED UPON OR AGAINST
THEM, PAYING PARTICULAR ATTENTION TO CORDS
AT PLUGS, CONVENIENCE RECEPTACLES, AND THE POINT WHERE
THEY EXIT FROM THE APPLIANCE.
CLEANING - THE APPLIANCE SHOULD BE CLEANED ONLY AS REC-
OMMENDED BY THE MANUFACTURER.
WATER & MOISTURE - DO NOT USE THE APPLIANCE NEAR
WATER; IE. BATHTUB, WASHBOWL, KITCHEN SINK, LAUNDRY
TUB, WET BASEMENT OR SWIMMING POOL.
NON USE PERIODS - UNPLUG THE APPLIANCE POWER CORD
FROM THE OUTLET WHEN LEFT UNUSED FOR A LONG PERIOD OF
TIME.
VENTILATION - DO NOT SITUATE THE APPLIANCE SO THAT
ITS LOCATION OR POSITION INTERFERES WITH ITS PROPER
VENTILATION. FOR EXAMPLE, THE APPLIANCE SHOULD NOT
BE SITUATED ON A BED, SOFA, RUG OR SIMILAR SURFACE THAT
MAY BLOCK THE VENTILATION OPENINGS. THE
OBJECT & LIQUID ENTRY - CARE SHOULD BE TAKEN SO THAT
OBJECTS DO NOT FALL AND LIQUIDS ARE NOT SPILLED INTO THE
ENCLOSURE THROUGH OPENINGS.
APPLIANCE SHOULD NOT BE PLACED IN A BUILT-IN
INSTALLATION, SUCH AS A BOOKCASE OR CABINET, THAT
MAY IMPEDE THE FLOW OF AIR THROUGH THE VENTILATION
OPENINGS.
DAMAGE REQUIRING SERVICE - THE APPLIANCE SHOULD BE SER-
VICED BY QUALIFIED SERVICE PERSONNEL WHEN: (A) THE POWER
SUPPLY CORD OR THE PLUG HAS BEEN DAMAGED (B) OBJECTS
HAVE FALLEN OR LIQUID HAS BEEN SPILLED INTO THE APPLIANCE
(C) THE APPLIANCE HAS BEEN EXPOSED TO RAIN (D) THE APPLI-
ANCE DOES NOT APPEAR TO BE OPERATING NORMALLY OR EXHIB-
ITS A MARKED CHANGE IN PERFORMANCE (E) THE APPLIANCE HAS
BEEN DROPPED OR THE ENCLOSURE DAMAGED.
HEAT - SITUATE THE APPLIANCE AWAY FROM HEAT SOURCES
SUCH AS RADIATORS, HEAT REGISTERS, STOVES OR OTHER AP-
PLIANCES (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.
POWER SOURCES - CONNECT THE APPLIANCE ONLY TO A
POWER SUPPLY TYPE DESCRIBED IN THE OPERATING INSTR-UC-
TIONS OR MARKED ON THE APPLIANCE.
SERVICING - THE USER SHOULD NOT ATTEMPT TO
SERVICE THE APPLIANCE BEYOND THAT DESCRIBED IN
THE OPERATING INSTRUCTIONS. ALL OTHER SERVICING REFER TO
A QUALIFIED SERVICE PERSONNEL.
GROUNDING OR POLARIZATION - PRECAUTIONS SHOULD BE
TAKEN SO THAT THE GROUNDING OR POLARIZATION MEANS OF
THE APPLIANCE ARE NOT DEFEATED.
Califone® International Inc. • 1145 Arroyo Avenue, # A • San Fernando, CA 91340 USA
Toll Free 800.722.0500 | Toll Free Fax 877.402.2248
International Customers call 818.407.2400 or Fax 818.407.2405 califone.com
August 2007
|