U S E R ’ S M A N U A L
page
CONTENTS
8 Farad Super
Power Capacitor
CAP8
2
Why use a power capacitor?
18 Farad Super Hybrid
Power Capacitor
CAP18
CAP30
2
4
6
Features
30 Farad Super Hybrid
Power Capacitor
Installation precautions
Important note about charging
the capacitor
Congratulations on your
purchase of a
Capacitor System.
Power
6
CAP18 and CAP30 electrical
connections
It has been designed, engineered
and manufactured to bring you
the highest level of performance
and quality, and will afford you
years of listening pleasure.
7
8
9
CAP8 electrical connections
Charging the capacitor
Discharging the capacitor
safely before removal
Thank you for making a
your choice for car audio
entertainment!
10 Specifications
CAP8 • CAP18 • CAP30 User’s Manual - page 1
General precautions
SHOCK HAZARD! Do not open the case
of this product. There are dangerous
voltages present within the unit. There are
no user-serviceable parts within the unit.
Before installing and using your new
capacitor, please become fa-
miliar with all the information con-
tained in this manual.
WARNING! This power capacitor may
explode and cause serious injury or
death if abused or connected
improperly.
Please keep this manual in a safe
place for future reference.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
are present which may result in electric
shock. Refer any repairs to a qualified
service technician.
Refer to this installation manual for correct
procedures when making connections,
and for charging and discharging the
capacitor. Never expose the capacitor to
voltages higher than specified!
• To avoid risk of electronic shock or
damage to the unit, do not permit any
of this equipment to become damp or
wet from water or drinks. If this does
occur, immediately unplug the power
wires and send the product to your
local dealer or service center as soon
as possible.
• If there is smoke or any peculiar odor
present during use or if there is damage
to any of the component enclosures,
immediately unplug the power cord
and send the product to your local
dealer or service center as soon as
possible .
CAP8 • CAP18 • CAP30 User’s Manual - page 3
Installation precautions
Prior to installing and connecting the capacitor, please study the drawing
below and become familiar with the physical features of the capacitor.
Securely mount the capacitor using the hardware provided. Be careful when
choosing a mounting location to avoid moving parts, and possible exposure to
moisture.
3-digit LED display
CAP8 terminal
locations
( – ) Negative terminal
Remote power connection terminal
( + ) Positive terminal
CAP8 • CAP18 • CAP30 User’s Manual - page 4
3-digit LED display
CAP18/CAP30
terminal locations
( + ) Positive OUTPUT terminal These terminals are
designed to accommodate
0GA and 4 GA cables.
( + ) Positive INPUT terminal
Remote power connection terminal
( – ) Negative OUTPUT terminal
( – ) Negative INPUT terminal
These terminals are
designed to accommodate
0GA and 4 GA cables.
CAP8 • CAP18 • CAP30 User’s Manual - page 5
Important note about charging the capacitor
This capacitor must be charged BEFORE connecting the POWER and GROUND
cable to the capacitor.
Failure to charge the capacitor will result in a large spark generated form the rapid
inflow of current which can be very dangerous.
Electrical connections for CAP18 or CAP30
Make all wiring connections as shown in the diagram, but do not attach the
incoming positive cable to the capacitor positive terminal.
Connect the positive terminal only after following the instructions for charging the
capacitor on page 8.
CAP8 • CAP18 • CAP30 User’s Manual - page 6
Electrical connections for CAP8
Make all wiring connections as shown in the diagram, but do not attach the
incoming positive cable to the capacitor positive terminal.
Connect the positive terminal only after following the instructions for charging the
capacitor on page 8.
CAP8 • CAP18 • CAP30 User’s Manual - page 7
Charging the capacitor
As noted earlier, make all connections according to the diagram(s) on the preceding
pages EXCEPT for the POSITIVE (+) connection to the capacitor. To charge the
capacitor, follow these steps:
1) Pick up the cable coming from the POSITIVE (+) battery terminal.
2) Place the supplied charging resistor between the end of this cable and the
positive terminal of the capacitor. The capacitor will begin charging. Charging
generally takes 5-60 seconds. During charging, the voltage shown in the 3-digit
display will rise rapidly, then slow as it approaches the voltage of your vehicle’s
battery. When fully charged, the displayed voltage will stop rising.
If you have a voltmeter, you can first measure the voltage of your car battery. Then
you will know with accuracy that the capacitor is fully charged.
CAUTION!! During charging, the resistor will become hot. This is normal, but exercise
caution during the charging process.
3) After charging is complete, remove the resistor from the incoming positive cable,
and IMMEDIATELY connect it to the positive terminal of the capacitor.
The installation and charging process are now complete, and you can begin using
your audio system and enjoying the benefits of your new system enhancement.
2 WATT/10 OHM
RESISTOR
(supplied)
CABLE FROM BATTERY
(+) POSITIVE
CAP8 • CAP18 • CAP30 User’s Manual - page 8
Discharging the capacitor
CAUTION!!
Never remove the capacitor without discharging the stored power. It can give a dangerous
electrical shock, even after disconnection.
To safely discharge and disconnect the capacitor, follow these steps:
1) Disconnect cables from the capacitor in the following order:
POSITIVE cable
GROUND cable
REMOTE cable
2) Using the resistor provided, touch one lead to the POSITIVE (+) terminal and one
lead to the NEGATIVE (-) terminal.
CAUTION!! During discharging, the resistor will become hot. This is normal, but
exercise caution during the discharging process.
After 1-5 minutes, the capacitor will be discharged ( the display will show 0.00V)
and you can safely remove and handle it.
RESISTOR
(supplied)
CAP8 • CAP18 • CAP30 User’s Manual - page 9
Specifications
30 Farad
Super Hybrid
Power Capacitor
18 Farad
8 Farad
Power
Super Hybrid
Power Capacitor Capacitor
MODEL
CAP30
CAP18
CAP8
Capacitance, microfarads
Working voltage
30,000,000
16VDC
18,000,000
16VDC
8,000,000
16VDC
Surge voltage
20VDC
20VDC
20VDC
ESR (Equivalent series resistance)
Capacitance tolerance
015 Ohm @ 120Hz/25ºC
0.0
+/- 10%
All specifications subject to
change without notice.
Size:
CAP 30
CAP18
9-1/4"
11"
CAP8
W:
L:
H:
7-3/4"
11-1/2"
3-1/2"
6-1/4"
9-3/4"
2-3/4"
3-1/4"
CAP8 • CAP18 • CAP30 User’s Manual - page 10
|