Bosch Appliances Security Camera VBN 5085 User Manual

DINION 5000 AN  
VBN-5085  
en Installation Manual  
 
DINION 5000 AN  
Table of Contents | en  
3
Table of Contents  
Safety  
Safety precautions  
System ground/Safety ground  
Important safety instructions  
Important notices  
FCC information  
UL certification  
Bosch notice  
Introduction  
Features  
Installation  
Unpacking  
Connection and mounting  
Power connection  
Low voltage cameras  
High voltage cameras  
Video connections  
Output Video signal  
Alarm and relay connector  
Lens mounting  
Back focus adjustment  
Mounting the camera  
Configuration  
Menus  
Top level menus  
Menu navigation  
Pre-defined modes  
Day/Night switching  
Camera control communication (Bilinx)  
Main menu structure  
Mode submenu  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
4
en | Table of Contents  
DINION 5000 AN  
Exposure submenu  
Day/Night submenu  
Enhance / Dynamic Engine submenu  
Color submenu  
VMD submenu  
Image Adjustment submenu  
Install menu structure  
Language submenu  
Lens Wizard submenu  
Synchronization submenu  
Alarm I/O submenu  
Connections submenu  
Test signal submenu  
Camera ID submenu  
Privacy masking submenu  
Flip submenu  
Defaults submenu  
Troubleshooting  
Resolving problems  
Customer service  
Maintenance  
Repairs  
Transfer and disposal  
Technical Data  
Specifications  
Dimensions  
Accessories  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
DINION 5000 AN  
Safety | en  
5
1
Safety  
1.1  
Safety precautions  
DANGER!  
High risk: This symbol indicates an imminently hazardous  
situation such as "Dangerous Voltage" inside the product.  
If not avoided, this will result in an electrical shock, serious  
bodily injury, or death.  
WARNING!  
Medium risk: Indicates a potentially hazardous situation.  
If not avoided, this could result in minor or moderate bodily  
injury.  
CAUTION!  
Low risk: Indicates a potentially hazardous situation.  
If not avoided, this could result in property damage or risk of  
damage to the unit.  
1.2  
System ground/Safety ground  
System (video) ground is indicated by the symbol  
.
.
Safety (power) ground is indicated by the symbol  
The system ground is only used to comply with safety standards  
or installation practices in certain countries. Bosch does not  
recommend connecting system ground to safety ground unless  
it is explicitly required. However, if the system ground and  
safety ground are connected and grounding loops are causing  
interference in the video signal, use an isolation transformer  
(available separately from Bosch).  
CAUTION!  
Connecting System ground to Safety ground may result in  
ground loops that can disrupt the CCTV system.  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
     
6
en | Safety  
DINION 5000 AN  
1.3  
Important safety instructions  
Read, follow, and retain for future reference all of the following  
safety instructions. Heed all warnings on the unit and in the  
operating instructions before operating the unit.  
1. Cleaning - Generally, using a dry cloth for cleaning is  
sufficient but a moist, fluff-free cloth or leather shammy  
may also be used. Do not use liquid cleaners or aerosol  
cleaners.  
2. Heat Sources - Do not install the unit near any heat  
sources such as radiators, heaters, stoves, or other  
equipment (including amplifiers) that produce heat.  
3. Water - Never spill liquid of any kind on the unit.  
4. Lightning - Take precautions to protect the unit from  
power and lightning surges.  
5. Controls adjustment - Adjust only those controls specified  
in the operating instructions. Improper adjustment of  
other controls may cause damage to the unit.  
6. Power sources - Operate the unit only from the type of  
power source indicated on the label.  
7. Servicing - Unless qualified, do not attempt to service this  
unit yourself. Refer all servicing to qualified service  
personnel.  
8. Replacement parts - Use only replacement parts specified  
by the manufacturer.  
9. Installation - Install in accordance with the manufacturer's  
instructions and in accordance with applicable local codes.  
10. Attachments, changes or modifications - Only use  
attachments/accessories specified by the manufacturer.  
Any change or modification of the equipment, not  
expressly approved by Bosch, could void the warranty or,  
in the case of an authorization agreement, authority to  
operate the equipment.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
 
DINION 5000 AN  
Safety | en  
7
1.4  
Important notices  
Disposal - Your Bosch product was developed and  
manufactured with high-quality material and components that  
can be recycled and reused. This symbol means that  
electronic and electrical appliances, which have reached the  
end of their working life, must be collected and disposed of  
separately from household waste material. Separate collecting  
systems are usually in place for disused electronic and  
electrical products. Please dispose of these units at an  
environmentally compatible recycling facility, per European  
Directive 2002/96/EC  
WARNING!  
Power disconnect for high voltage versions: A unit has power  
supplied whenever the power cord is inserted into the power  
source. The power cord plug is the main power disconnect for  
the unit. For pluggable equipment, install the socket outlet near  
the equipment so it is easily accessible.  
WARNING!  
All-pole power switch: Incorporate an all-pole power switch,  
with a contact separation of at least 3 mm in each pole, into the  
electrical installation of the building.  
CAUTION!  
Fuse rating: The branch circuit protection must be secured with  
a maximum fuse rating of 16 A. This must be in accordance with  
NEC800 (CEC Section 60).  
CAUTION!  
The Low Voltage power supply unit must comply with EN/UL  
60950. The power supply must be a SELV-LPS unit or a SELV -  
Class 2 unit (Safety Extra Low Voltage - Limited Power Source).  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
 
8
en | Safety  
DINION 5000 AN  
1.5  
FCC information  
FCC & ICES Information  
(U.S.A. and Canadian Models Only)  
This equipment has been tested and found to comply with the  
limits for a Class B digital device, pursuant to part 15 of the  
FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference  
to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following  
measures:  
reorient or relocate the receiving antenna;  
increase the separation between the equipment and  
receiver;  
connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected;  
consult the dealer or an experienced radio/TV technician  
for help.  
Intentional or unintentional modifications, not expressly  
approved by the party responsible for compliance, shall not be  
made. Any such modifications could void the user's authority to  
operate the equipment. If necessary, the user should consult  
the dealer or an experienced radio/television technician for  
corrective action.  
The user may find the following booklet, prepared by the  
Federal Communications Commission, helpful: How to Identify  
and Resolve Radio-TV Interference Problems. This booklet is  
available from the U.S. Government Printing Office,  
Washington, DC 20402, Stock No. 004-000-00345-4.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
 
DINION 5000 AN  
Safety | en  
9
1.6  
UL certification  
Disclaimer  
Underwriter Laboratories Inc. ("UL") has not tested the  
performance or reliability of the security or signaling aspects of  
this product. UL has only tested fire, shock and/or casualty  
hazards as outlined in UL's Standard(s) for Safety for Information  
Technology Equipment, UL 60950-1. UL Certification does not  
cover the performance or reliability of the security or signaling  
aspects of this product.  
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR  
CERTIFICATIONS WHATSOEVER REGARDING THE  
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR  
SIGNALING-RELATED FUNCTIONS OF THIS PRODUCT.  
1.7  
Bosch notice  
More information  
For more information please contact the nearest Bosch Security  
Systems location or visit www.boschsecurity.com  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
   
10 en | Introduction  
DINION 5000 AN  
2
Introduction  
2.1  
Features  
The DINION 5000 Day/Night WDR camera is a high-  
performance, smart, surveillance color camera. It uses a wide  
dynamic range 960H CCD sensor for outstanding picture  
performance.  
The camera is easy to install and ready to use, and offers the  
best solution for demanding scene conditions. Features  
include:  
1/3-inch 960H CCD sensor with wide dynamic range  
True Day/Night performance with switchable IR filter  
720TVL sensor resolution  
High Dynamic Range  
Privacy zones  
Detail enhancement  
Bilinx (bi-directional coaxial communication)  
Wide operating temperature range  
Lens wizard  
Six pre-programmed operation modes  
Dynamic noise reduction  
Multiple language on-screen display  
Built-in test pattern generator  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
   
DINION 5000 AN  
Installation | en 11  
3
Installation  
3.1  
Unpacking  
Unpack carefully and handle the equipment with care.  
The packaging contains:  
DINION 5000 camera  
CCD protection cap (mounted on camera)  
Alarm I/O connector  
Power connector  
Important safety instructions  
Quick install instructions  
CD-ROM  
Installation instructions  
If equipment has been damaged during shipment, repack it in  
the original packaging and notify the shipping agent or supplier.  
WARNING!  
Installation should only be performed by qualified service  
personnel in accordance with the National Electrical Code  
NEC800 (CEC Section 60) or applicable local codes.  
CAUTION!  
The camera module is a sensitive device and must be handled  
carefully.  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
   
12 en | Connection and mounting  
DINION 5000 AN  
4
Connection and mounting  
CAUTION!  
Before proceeding, disconnect the power from the power  
supply cable. Ensure that the voltage of the unit matches the  
voltage and type of the power supply being used.  
4.1  
Power connection  
4.1.1  
Low voltage cameras  
1
2
3
5 mm  
Figure 4.1 Low voltage power connection  
Connect power from a 24 VAC or 12 VDC class 2 power supply  
as follows:  
Use AWG16 to 22 stranded wire or AWG16 to 26 solid  
wire; cut back 5 mm (0.2 in) of insulation.  
Remove the 3-pole connector from the camera body.  
Loosen the screws and insert the wires.  
Note  
The central connection for System (video) ground is  
optional. Connecting System ground to Safety ground may  
result in ground loops that can disrupt the CCTV system.  
Tighten the screws and reconnect the 3-pole connector to  
the camera.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
     
DINION 5000 AN  
Connection and mounting | en 13  
Note  
For a DC supply the polarity is important. Incorrect polarity  
does not damage the camera but it will not switch on. For an  
AC supply maintain a consistent wiring polarity in multiple  
camera systems to help avoid potential camera video rolling.  
4.1.2  
High voltage cameras  
1
2
3
4
5
6
Figure 4.2 High voltage power connection  
Connect the power cable of a high voltage camera to a 230 VAC  
power supply outlet.  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
 
14 en | Connection and mounting  
DINION 5000 AN  
4.2  
Video connections  
VIDEO  
Video BNC  
AL  
ARM  
1
2
3
4
5
6
Figure 4.3 BNC connectors  
4.2.1  
Output Video signal  
The camera has a BNC connector to connect the video coax  
cable with a male BNC connector. A UTP adapter (VDA-455UTP)  
is available as an optional accessory to allow a UTP video cable  
to be connected to the BNC connector.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
   
DINION 5000 AN  
Connection and mounting | en 15  
4.3  
Alarm and relay connector  
ALARM  
1
2
3
4
5
6
5 mm  
(0.2 in)  
Figure 4.4 Alarm and relay connector pins  
Pin  
1
Alarm socket  
Alarm in  
2
not used  
3
Relay out contact 2  
Alarm in ground  
not used  
4
5
6
Relay out contact 1  
Max. wire diameter AWG 22-28 for both stranded and  
solid; cut back 5 mm (0.2 in) of insulation.  
Alarm output relay switching capability: Max voltage 30VAC  
or +40 VDC. Max 0.5 A continuous, 10 VA.  
Alarm in: TTL logic, +5V nominal, +40 VDC max, DC coupled  
with 22 kOhm pull-up to +3.3 V.  
Alarm in: configurable as active low or active high.  
Max. 42 V allowed between camera ground and each of the  
relay pins.  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
 
16 en | Connection and mounting  
DINION 5000 AN  
4.4  
Lens mounting  
The camera accepts CS-mount lenses. C-mount lenses can be  
mounted using the lens adapter ring. DC-iris lenses are  
recommended for the best picture performance.  
CAUTION!  
To avoid damaging the CCD sensor when using a C-mount lens,  
make sure the supplied lens adapter ring is mounted onto the  
camera before mounting the lens.  
Lenses weighing more than 0.5 kg (1.1lbs) must be separately  
supported.  
Bosch  
Bosch  
Figure 4.6 Lens connector  
Figure 4.5 Mounting a lens  
Pin Video iris lens  
DC iris lens  
1
2
3
4
Supply (11.5V 0.5, 50mA max.)  
Damp -  
Damp +  
Drive +  
Drive -  
Not used  
Video signal 1Vpp 1kOhm  
Ground  
Note  
If a short circuit is detected on the lens connector, the on-  
screen display (OSD) failure message LENS SHORT CIRCUIT is  
shown. The lens circuit is automatically disabled to avoid  
internal damage. Remove the lens connector and check the pin  
connections.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
 
DINION 5000 AN  
Connection and mounting | en 17  
4.5  
Back focus adjustment  
To optimize picture sharpness in both bright and low-level  
lighting, adjust the back focus. Use the camera's unique Lens  
Wizard. This ensures that the object of interest always remains  
in focus, even when focusing at the maximum lens iris opening  
(for example, at night).  
When back focusing varifocal lenses, adjust to obtain a  
sharp picture in both wide-angle and tele positions for  
both far and near focus.  
When back focusing zoom lenses, ensure the object of  
interest remains in focus throughout the entire zoom range  
of the lens.  
To adjust back focus:  
1. Open the slide door panel at the side of the camera.  
1. Unlock the back focus locking button.  
2. Press and hold the center key for more than 1 second until  
the Install menu appears.  
3. Select Len Wizard and move cursor to the Set Back Focus  
Now item.  
4. Turn the back focus adjustment as required.  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
 
18 en | Connection and mounting  
DINION 5000 AN  
5. Lock the back focus locking button.  
6. Press and hold the center key for more than 1 second until  
all the menus disappear.  
7. Close the side door panel.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
DINION 5000 AN  
Connection and mounting | en 19  
4.6  
Mounting the camera  
The camera can be mounted either from the top or from the  
bottom (1/4" 20 UNC thread). The bottom mounting is isolated  
from ground to prevent ground loops.  
Figure 4.7 Mounting a camera  
CAUTION!  
Do not point the camera/lens into direct sunlight as this may  
damage the sensors.  
Note:  
A wide range of accessories is available for indoor and outdoor  
mounting.  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
 
20 en | Configuration  
DINION 5000 AN  
5
Configuration  
The camera normally provides an optimal picture without the  
need for further adjustments. Advanced set-up options are  
available in a menu system for getting the best results under  
special circumstances.  
The camera implements your changes immediately so that  
before and after settings are easily compared.  
5.1  
Menus  
5.1.1  
Top level menus  
There are two upper level menus: a Main menu and an Install  
menu. The menus have functions that can be selected directly  
or submenus for more detailed set-up.  
To access the Main menu, press the menu/select button  
(center) for less than 1 second. The Main menu appears on  
the monitor. The Main menu allows you to select and set-  
up the picture enhancement functions. If you are not happy  
with your changes, you can always recall the default values  
for the mode.  
The camera also has an Install menu in which the  
installation settings can be set. To access the Install menu,  
press the menu/select button (center) for longer than 2  
seconds.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
     
DINION 5000 AN  
Configuration | en 21  
5.1.2  
Menu navigation  
Five keys, located behind the side door panel, are used for  
navigating through menu system.  
Figure 5.1 Side panel door  
Figure 5.2 Menu/select key  
Up key  
Menu/Select key (center)  
Right key  
Down key  
Left key  
Figure 5.3 Navigation  
Use the up or down keys to scroll through a menu.  
Use the left or right keys to move through options or to set  
parameters.  
When in a menu, quickly double-press the menu/select key  
to restore the selected item to its factory default.  
To close all menus at once hold down the menu/select key  
until the menu display disappears or continually select the  
Exit item.  
Some menus automatically close after about two minutes; other  
menus have to be closed manually.  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
 
22 en | Configuration  
DINION 5000 AN  
5.2  
Pre-defined modes  
There are six pre-defined modes with settings to make  
configuration easier. You can select one of the six pre-defined  
modes in the Install/Mode submenu. The modes are defined as  
follows;  
1. 24-hour  
Default installation mode to provide stable pictures over a  
24-hour period. These settings are optimized for out-of-  
the-box installation.  
2. Traffic  
Capture high-speed objects using default shutter in  
variable lighting conditions.  
3. Low light  
Provide extra enhancement, such as AGC and SensUp to  
make usable pictures in low-light conditions.  
4. Smart BLC  
Settings optimized to capture details in high contrast and  
extremely bright-dark conditions.  
5. Low noise  
Enhancements are set to reduce picture noise. Useful for  
conditional refresh DVR and IP storage systems because  
reducing noise reduces the amount of storage required.  
6. Vibrant  
This mode has enhanced contrast, sharpness and  
saturation.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
 
DINION 5000 AN  
Configuration | en 23  
5.3  
Day/Night switching  
The camera is equipped with a motorized IR filter. The  
mechanical IR filter can be removed in low-light or IR  
illuminated applications by software configuration settings.  
If Auto switching mode is selected, the camera automatically  
switches the filter depending on the observed light level. The  
switching level is programmable. In Auto switching mode the  
camera prioritizes motion (the camera gives sharp images  
without motion blur as long as the light level permits) or color  
(the camera gives color pictures as long as the light level  
permits). The camera recognizes IR illuminated scenes to  
prevent unwanted switching to color mode.  
There are four different methods of controlling the IR filter:  
via an alarm input,  
via Bilinx communication,  
automatically, based on the observed light levels, or  
as part of the programmable mode profile.  
5.4  
Camera control communication (Bilinx)  
This camera is equipped with a coaxial communications  
transceiver (also referred to as Bilinx). In combination with VP-  
CFGSFT, the camera setting can be changed from any point  
along the coaxial cable. All menus can be accessed remotely  
giving full control of the camera. With this method of  
communication it is also possible to disable the local keys on  
the camera.To avoid loss of communication on an installed  
camera, the Communication On/Off selection is not available  
while using remote control. This function can only be accessed  
with the camera buttons. Bilinx communications can only be  
disabled using the buttons on the camera.  
Disabled camera buttons  
When the Bilinx communications link is active, the buttons on  
the camera are disabled.  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
   
24 en | Configuration  
DINION 5000 AN  
5.5  
Main menu structure  
Item  
Selection  
Submenu  
Submenu  
Submenu  
Submenu  
Submenu  
Submenu  
Submenu  
Description  
Mode  
Sets up operating modes 1 to 6  
Exposure control  
Exposure  
Day/Night  
Enhance  
Color  
Day/Night for color/mono operation  
Picture enhancement and performance  
White balance and color rendition  
Video motion detection  
VMD  
Image  
Sets up digital zoom or digital image  
stabilization  
Adjustment  
5.5.1  
Mode submenu  
Item  
Selection  
Description  
Mode  
1 to 6  
Selects operating mode.  
Mode name (11 characters maximum)  
Mode ID  
Alphanumeric  
Copy active  
mode  
Available  
mode  
Copies current mode settings to the  
mode number selected.  
numbers  
Mode  
Submenu  
Restores camera to the factory default  
settings.  
Defaults  
EXIT  
Returns to main menu.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
   
DINION 5000 AN  
Configuration | en 25  
5.5.2  
Exposure submenu  
Item  
Selection  
Description  
ALC level  
-15 to +15  
Selects the video level range. A  
positive value is more useful for low-  
light conditions; a negative value is  
more useful for very bright  
conditions.  
Some ALC adjustment may improve  
scene content when Smart BLC is  
enabled.  
ALC speed  
Shutter  
Slow,  
Adjusts the speed of the video level  
control loop. For most scenes it  
should remain at the default value.  
medium, fast  
AES, FL, Fixed  
AES (auto-shutter) - the camera  
automatically sets the optimum  
shutter speed.  
FL - flickerless mode avoids  
interference from light sources  
(recommended for DC-iris lenses  
only).  
FIXED - allows a user defined shutter  
speed.  
Default (AES)  
shutter  
1/50 (PAL)  
1/60 (NTSC),  
1/100 (PAL)  
1/120 (NTSC),  
1/250,  
In DEFAULT (AES) mode, the camera  
tries to maintain the selected shutter  
speed as long as the light level of the  
scene is high enough.  
or  
Fixed shutter  
In Fixed mode, selects shutter  
speed.  
1/500,  
1/1000,  
1/2000,  
1/4000,  
1/10K,  
1/100K  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
 
26 en | Configuration  
DINION 5000 AN  
Item  
Selection  
Description  
Actual shutter  
Displays the actual shutter value  
from the camera to help compare  
lighting levels and optimum shutter  
speed during set-up.  
Gain control  
On, Fixed  
0 to 40 dB  
On - the camera automatically sets  
the gain to the lowest possible value  
needed to maintain a good picture.  
Fixed - sets Fixed AGC value.  
Maximum AGC  
or  
Selects the maximum value the gain  
can have during AGC operation.  
Selects the gain setting for Fixed  
gain operation (0 is no gain).  
Fixed AGC  
Actual AGC  
Displays the actual AGC value from  
the camera to help compare gain  
level with lighting levels and picture  
performance.  
SensUp  
Off, 2x,  
Selects the factor by which the  
sensitivity of the camera is  
increased.  
Dynamic  
3x, …, 10x  
When active, some noise or spots  
may appear in the picture. This is  
normal camera behavior. It may also  
cause motion blur on moving  
objects.  
EXIT  
Returns to main menu.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
DINION 5000 AN  
Configuration | en 27  
5.5.3  
Day/Night submenu  
Item  
Selection  
Description  
Day/Night  
Auto, Color,  
Auto - the camera switches the IR cut-  
off filter on and off depending on the  
scene illumination level.  
Monochrome  
Color - the camera always produces a  
color signal regardless of light levels.  
Monochrome - the IR cut-off filter is  
removed, giving full IR sensitivity.  
Switch level  
-15 to +15  
Sets the video level in Auto mode at  
which the camera switches to  
monochrome operation.  
A low (negative) value means that the  
camera switches to monochrome at a  
lower light level. A high (positive) value  
means that the camera switches to  
monochrome at a higher light level.  
Switch delay  
Priority  
1, 2, 3, 5, 10,  
20, 30, 60,  
120, 240 s  
Sets the evaluation time in Auto mode  
for day to night transitions.  
Motion, Color  
In AUTO mode:  
Color - the camera gives a color image  
as long as the light level permits.  
Motion - the camera avoids motion blur  
as long as the light level permits (it  
switches to monochrome earlier than it  
would with Color priority).  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
 
28 en | Configuration  
DINION 5000 AN  
Item  
Selection  
Description  
IR contrast  
(mono)  
Enhanced,  
Normal  
Enhanced - the camera optimizes  
contrast in applications with high IR  
illumination levels. Select this mode  
for IR (730 to 940 nm) light sources  
and for scenes with grass and green  
foliage.  
Normal - the camera optimizes contrast  
in mono applications with visible light  
illumination.  
IR  
0 to +15  
On, Off  
Enter the strength of the external IR  
illumination to determine the night to  
day transition moment. 0 is no IR  
illuminator; +15 is very strong  
illumination.  
illumination  
(mono)  
Color burst  
(mono)  
Off - the color burst in the video signal  
is switched Off in monochrome mode.  
On - the color burst remains active  
even in monochrome mode (required  
by some DVRs and IP encoders).  
EXIT  
Returns to main menu.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
DINION 5000 AN  
Configuration | en 29  
5.5.4  
Enhance / Dynamic Engine submenu  
Item  
Selection  
Description  
Dynamic  
Off,  
Off: - turns off all automatic scene  
detail and enhancements (only  
recommended for testing).  
Engine  
XF DYNAMIC,  
HDR,  
Smart BLC  
XF DYNAMIC: - extra internal  
processing is enabled for enhancing  
the visibilty.  
HDR: - adds dual sensor exposure to  
the XF DYNAMIC features. In harsh  
lighting conditions, pixels from each  
exposure are mixed to give a more  
detailed image.  
Smart BLC: - BLC window and  
weighting factor are automatically  
defined. Camera dynamically adjusts  
these for changing light conditions.  
Contrast  
Low,  
Increases the contrast at medium  
brightness levels.  
Enhancement  
Medium,  
High  
Select Low for high contrast scenes.  
Select High for low contrast scenes  
(e.g. fog).  
Sharpness  
-15 to +15  
Adjusts the sharpness of the picture. 0  
corresponds to the default position.  
A low (negative) value makes the  
picture less sharp. Increasing  
sharpness brings out more detail.  
Extra sharpness can enhance the  
details of license plates, facial features  
and the edges of certain surfaces.  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
 
30 en | Configuration  
DINION 5000 AN  
Item  
Selection  
Description  
3D-NR  
Off,  
Automatically reduces the noise in the  
picture.  
Low,  
Medium,  
High  
This may cause some motion blur on  
exceptionally fast moving objects  
immediately in front of the camera.  
This can be corrected by widening the  
field of view or lowering the selection  
value.  
2D-NR  
Off,  
Automatically reduces the noise in the  
picture.  
Low,  
Medium,  
High  
A high selection may cause blur.  
A lower selection improves sharpness  
at the cost of more noise  
Peak White  
Invert  
On, Off  
Use Peak White Invert to reduce glare  
from the CRT/LCD display.  
Use in ANPR/LPR applications to  
reduce headlight glare.  
(Test on-site to ensure that it does  
benefit the application and is not  
distracting for operators of the security  
system.)  
EXIT  
Returns to main menu.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
DINION 5000 AN  
Configuration | en 31  
5.5.5  
Color submenu  
Item  
Selection  
Description  
White balance  
ATW indoor,  
ATW Outdoor,  
ATW hold,  
Manual  
ATW - Auto tracking white balance  
allows the camera to constantly  
adjust for optimal color  
reproduction.  
ATW hold - Puts the ATW on hold and  
saves the color settings.  
Manual - the Red and Blue gain can  
be manually set to a desired position.  
Speed  
Fast,  
Adjusts the speed of the white  
balance control loop.  
Medium,  
Slow  
Red gain  
Blue gain  
Saturation  
-50 to +50  
-50 to +50  
-15 to +5  
Manual and ATW hold - adjusts the  
Red gain.  
Manual and ATW hold - adjusts the  
Blue gain.  
Adjusts the color saturation. -15  
gives a monochrome image; 0 gives  
the default saturation; +15 gives the  
most saturation.  
EXIT  
Returns to main menu.  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
 
32 en | Configuration  
DINION 5000 AN  
5.5.6  
VMD submenu  
Item  
Selection  
Description  
VMD area  
Submenu  
Select 1 of the 4 areas to enter the  
area set-up menu to define the  
detection area.  
VMD mode  
Off, Silent,  
OSD  
Off - Video Motion Detection (VMD) is  
off.  
Silent - video motion generates silent  
alarm.  
OSD - video motion generates on-  
screen text message alarm.  
VMD  
0 to 127  
Sets the sensitivity for motion to the  
desired level. The longer the white bar,  
the more motion is required to acitvate  
the VMD alarm. Motion above this level  
activates alarm.  
sensitivity  
OSD alarm  
text  
Alphanumeric  
Text for on-screen display alarm (16  
characters maximum).  
EXIT  
Returns to main menu.  
Selecting an area for VMD masking  
To set-up an area for VMD masking, access the area menu by  
selecting the VMD Area option from the VMD menu. Upon  
entering the Area menu, the current area is displayed with the  
upper left corner flashing. The flashing corner of the image can  
be moved with the Up, Down, Left, Right arrow keys. Pressing  
the Select key moves the flashing cursor to the opposite corner,  
which can now be moved. Pressing Select again freezes the  
area and exits the area menu.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
 
DINION 5000 AN  
Configuration | en 33  
5.5.7  
Image Adjustment submenu  
Item  
Selection  
Description  
Digital Zoom  
x1, x2, x4, x8,  
x16  
Select the zoom factor  
DIS  
Off, On  
Select On to stabilize the image.  
Returns to main menu.  
EXIT  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
 
34 en | Configuration  
DINION 5000 AN  
5.6  
Install menu structure  
Item  
Selection  
Description  
Language  
Submenu  
Select on-screen display (OSD)  
language  
Lens Wizard  
Submenu  
Submenu  
Submenu  
Select to optimize the camera-lens  
combination backfocus point.  
Synchroniza-  
tion  
Sets synchronization parameters  
Alarm I/O  
Program the alarm input and output  
functionality.  
Connections  
Test signals  
Camera ID  
Submenu  
Submenu  
Submenu  
Submenu  
Connection parameters  
Test patterns and texts  
Select to access ID submenu  
Sets up a masking area  
Privacy  
masking  
Flip  
Submenu  
Submenu  
Selects flip submenu  
Default ALL  
Returns all settings for all modes to  
factory defaults  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
 
DINION 5000 AN  
Configuration | en 35  
5.6.1  
Language submenu  
Item  
Selection  
Description  
Language  
English  
Displays the menus on the OSD in the  
chosen language.  
Spanish  
French  
German  
Portuguese  
Russian  
Simplified  
Chinese  
EXIT  
Returns to Install menu.  
5.6.2  
Lens Wizard submenu  
Item  
Selection  
Description  
Lens type  
Manual, DC-  
iris  
Select the matching lens type to force  
the camera to the correct lens mode.  
DC- iris setup  
Open,  
Selects the type of control for DC-iris  
lens.  
Close, Auto  
Open - the DC-iris is fixed to open.  
Close - the DC-iris is fixed to close.  
Auto - the aperture of the lens is  
adjusted automatically.  
DC-iris speed  
0,1,2…255  
Adjusts the convergence speed of DC-  
iris.  
DC-iris  
The convergence speed is  
calibration  
automatically determined using the  
built-in calibration mechanism.  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
   
36 en | Configuration  
DINION 5000 AN  
Item  
Selection  
Description  
Set Backfocus  
now  
Select to fully open the iris. Follow the  
instructions below for setting the  
backfocus for your particular lens type.  
After focusing the object of interest  
remains in focus under bright and low  
light conditions.  
EXIT  
Returns to Install menu.  
Adjustment procedure DC-iris Lens  
1. Unlock the back focus locking button.  
2. Access the Lens Wizard menu.  
3. Set Back Focus Now is highlighted in the menu.  
4. Turn the back focus adjustment as required.  
5. Lock the back focus locking button.  
6. Exit the menu.  
Adjustment procedure Manual-iris Lens  
1. Unlock the back focus locking button.  
2. Adjust the lens to the maximum lens opening.  
3. Turn the back focus adjustment as required.  
4. Lock the back focus locking button.  
5. Adjust lens opening to suit scene.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
DINION 5000 AN  
Configuration | en 37  
5.6.3  
Synchronization submenu  
Item  
Selection  
Description  
Synchroniza-  
Internal  
Internal - for free running camera  
operation.  
tion  
Line lock  
Line lock - to lock to the AC power  
supply  
Vertical phase  
EXIT  
0, 1, … 359  
Adjusts the vertical phase offset (when  
in LINE LOCK mode and a valid power  
supply frequency is detected).  
Returns to Install menu.  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
 
38 en | Configuration  
DINION 5000 AN  
5.6.4  
Alarm I/O submenu  
Item  
Selection  
Description  
Input  
None, high,  
low  
Select none to disable the alarm input.  
Select active-high or active-low for the  
alarm input connector.  
Input action  
Output  
None,  
Selects the operating mode of the  
Mode 1 to 6,  
Night mode  
camera when the alarm input is active.  
Normally  
open,  
Selects the relay output mode.  
Normally  
closed  
Output action  
VMD,  
VMD: - output relay closes on VMD  
alarms.  
Ext. device,  
Night mode,  
Filter toggle  
External device: - make the output  
relay available to remote  
communication devices.  
Night mode: - output relay closes when  
camera is in monochrome mode.  
Filter toggle: - output relay closes just  
before the IR filter starts moving and  
opens when video level has stabilized  
(2 to 3 seconds)  
EXIT  
Returns to Install menu.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
 
DINION 5000 AN  
Configuration | en 39  
5.6.5  
Connections submenu  
Item  
Selection  
Description  
Bilinx Comms.  
On, Off  
If Off, Bilinx communications is  
disabled.  
Camera  
buttons  
Enable,  
disable  
Enable or disable the camera buttons  
from working.  
Cable  
Off, Default,  
RG59, RG6  
Cable compensation is used to avoid  
the need for amplifiers in long distance  
coaxial connections up to 1000 m  
(3000 ft). For optimum results select  
the coaxial cable type used or, if  
unknown, select default.  
compensation  
Compensation  
level  
0,1,2 . . .+15  
Sets the level of cable compensation  
EXIT  
Returns to Install menu.  
5.6.6  
Test signal submenu  
Item  
Selection  
Description  
Show camera  
Off, On  
Select On to overlay the camera ID on  
the video test signal.  
ID  
Test pattern  
Color bars,  
Raster,  
Select the desired test pattern to help  
installation and fault-finding.  
Impulse,  
Cross  
Impulse,  
Crosshatch  
EXIT  
Returns to Install menu.  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
   
40 en | Configuration  
DINION 5000 AN  
5.6.7  
Camera ID submenu  
Item  
Selection  
Description  
Camera ID  
Enter a 17-character camera name. Use  
Left/Right to change position in the  
string; use up/down to select  
character. Use Select to exit.  
Display ID pos.  
Off, Top left,  
Top right,  
Select the screen position of the  
camera ID.  
Bottom left,  
Bottom right  
Camera ID  
border  
On, Off  
Displays a grey border behind the  
camera ID to make it easier to read.  
MAC address  
Shows MAC address (factory set,  
cannot be changed).  
Ticker bars  
On, Off  
The ticker bar moves continuously to  
show that the image is live and not  
frozen or played back.  
Mode ID pos.  
Off, Top left,  
Top right,  
Camera mode is displayed on the  
screen in the selected position.  
Bottom left,  
Bottom right  
EXIT  
Returns to Install menu.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
 
DINION 5000 AN  
Configuration | en 41  
5.6.8  
Privacy masking submenu  
Item  
Selection  
Description  
Mask  
1 to 15  
15 different areas can be masked.  
Selects pattern for all masks.  
Pattern  
Black, Grey,  
White, Noise  
Active  
On, Off  
On, Off  
Submenu  
Turns each of the masks on or off.  
Turns mosaic on or off.  
Mosaic  
Window  
Select to open a window in which to  
define the mask area.  
Selecting an area for privacy masking  
To set-up an area for privacy masking, access the area menu by  
selecting the Area option from the privacy masking menu. Upon  
entering the Area menu, the current area is displayed with the  
upper left corner flashing. The flashing corner of the image can  
be moved with the Up, Down, Left, Right arrow keys. Pressing  
the Select key moves the flashing cursor to the opposite corner,  
which can now be moved. Pressing Select again freezes the  
area and exits the area menu.  
5.6.9  
Flip submenu  
Item  
Selection  
Description  
Flip  
Off  
Selects the flip mode.  
horizontal  
Vertical  
Both  
EXIT  
Returns to Install menu.  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
   
42 en | Configuration  
DINION 5000 AN  
5.6.10  
Defaults submenu  
Item  
Selection  
Description  
Restore All  
No, Yes  
Restores all settings of the six modes  
to their default (factory) values. Select  
YES then press the Menu/Select  
button to restore all values.  
When completed the message  
RESTORED! is shown.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
 
DINION 5000 AN  
Troubleshooting | en 43  
6
Troubleshooting  
6.1  
Resolving problems  
The following table is intended to help you identify the causes  
of malfunctions and correct them when possible.  
Malfunction  
Possible causes  
Solution  
No image  
Defective camera.  
Connect a local monitor  
to the camera and check  
the camera function.  
transmission to  
remote location.  
Faulty cable connections. Check all cables, plugs,  
contacts and  
connections.  
Incorrect cable  
connections.  
When using DC power  
ensure that polarity is  
correct.  
No connection  
The unit's configuration.  
Faulty installation.  
Check all configuration  
parameters.  
established, no  
image transmission.  
Check all cables, plugs,  
contacts and  
connections.  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
   
44 en | Troubleshooting  
DINION 5000 AN  
6.2  
Customer service  
If you cannot resolve a fault, please contact your supplier or  
system integrator, or contact Bosch Security Systems  
Customer Service directly.  
The Installer should write down all information regarding the  
unit so that it can be referenced for warranty or repair. The  
version numbers of the firmware and other status information  
can be seen when the unit starts or by opening the Install  
menu. Note down this information and the information found  
on the camera label before contacting customer service.  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
 
DINION 5000 AN  
Maintenance | en 45  
7
Maintenance  
7.1  
Repairs  
CAUTION!  
Never open the casing of the camera. The unit does not contain  
any user serviceable parts. Ensure that all maintenance or  
repair work is performed only by qualified personnel (electrical  
engineering or network technology specialists). If in doubt,  
contact your dealer's technical service center.  
7.1.1  
Transfer and disposal  
The camera should only be passed-on together with this  
installation guide. The unit contains environmentally hazardous  
materials that must be disposed of according to law. Defective  
or superfluous devices and parts should be disposed of  
professionally or taken to your local collection point for  
hazardous materials.  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
     
46 en | Technical Data  
DINION 5000 AN  
8
Technical Data  
8.1  
Specifications  
Type number  
Standard  
VBN-5085-C11  
PAL  
VBN-5085-C21  
NTSC  
VBN-5085-C51  
PAL  
Active pixels  
976 x 582  
976 x 494  
976 x 582  
230 VAC 50 Hz  
Rated supply  
voltage  
+12 VDC  
+12 VDC  
24 VAC (50 Hz)  
24 VAC (60 Hz)  
All versions  
Imager  
1/3-inch 960H CCD  
Resolution  
720TVL sensor resolution  
Sensitivity  
(30IRE)  
<0.04 lux  
<0.02 lux (in monochrome mode)  
SNR  
> 54 dB  
Video output  
1 Vpp, 75 Ohm  
Internal, Line Lock  
Synchroniza-  
tion  
Shutter  
Auto (1/60 [1/50] to 1/100000)  
Selectable, fixed, flickerless, default  
Day/Night  
Sens Up  
AGC  
Color, Mono, Auto  
Adjustable from Off to 10x  
AGC On or Off (0 - 40 dB) selectable  
Dynamic engine XF Dynamic, HDR, Smart BLC  
Dynamic Range 94 dB  
Dynamic Noise  
Reduction  
3D-NR, 2D-NR  
Sharpness  
Sharpness enhancement level selectable  
ATW indoor, ATW outdoor, ATW hold and manual  
Low, Medium, High  
White Balance  
Contrast  
Enhancement  
Lens type  
Manual or DC iris  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
   
DINION 5000 AN  
Lens mount  
Technical Data | en 47  
CS compatible, C-mount compatible with optional  
adapter ring  
Test pattern  
generator  
Color bar, Raster, Impulse, Cross Impulse, Cross hatch  
Video Motion  
Detection  
(VMD)  
4 areas, fully programmable  
Privacy Masking 15 independent areas, fully programmable; black, white,  
grey, noise  
E-zoom  
Up to 16x  
On/Off  
Digital Image  
Stabilizer  
Communication Two-way Bilinx (bi-directional)  
Languages  
(OSD)  
English, Spanish, French, German, Portuguese, Russian,  
Simplified Chinese  
Modes  
6 programmable (preset) modes: 24-hour, Traffic, Low-  
light, Smart BLC, Low noise, Vibrant  
Peak White  
Invert  
Suppresses highlights in scenes  
Power  
12 VDC 360 mA24 VAC 330 mA120-240 VAC 60 mA  
58 x 66 x 122 mm (2.28 x 2.60 x 4.80 in) without lens  
500 g (1.10 lb) without lens  
consumption  
Dimensions  
(H x W x L)  
Weight  
(12 VDC/  
24 VAC)  
Weight  
600 g (1.32 lb) without lens  
(230 VAC)  
Tripod mount  
Bottom (isolated) and top 1/4" 20 UNC  
-20 °C to +55 °C (-4 °F to +131 °F)  
Operating  
temperature  
Controls  
OSD with softkey operation  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
48 en | Technical Data  
DINION 5000 AN  
8.1.1  
Dimensions  
118 (4.646)  
85 (3.346)  
34 (1.339)  
1/4"-20 UNC  
DINION  
1/4"-20 UNC  
48 (1.889)  
123 (4.843)  
67 (2.638)  
mm (in)  
Figure 8.1 Dimensions  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
 
DINION 5000 AN  
Technical Data | en 49  
8.1.2  
Accessories  
Indoor mounting brackets  
Outdoor environmental housings  
Lenses (varifocal, fixed and motorized zoom)  
Bilinx communication interface box and software  
Contact a Bosch representative in your area for the latest  
available accessories or visit our website at  
Bosch Security Systems  
Installation Manual  
AM18-Q0644 | v1.0 | 2013.03  
 
 
50 en | Technical Data  
DINION 5000 AN  
AM18-Q0644 | v1.0 | 2013.03  
Installation Manual  
Bosch Security Systems  
 
 
Bosch Security Systems  
© Bosch Security Systems, 2013  
 

Black Decker Blender FP1550SDC User Manual
Black Decker Cordless Saw 90503809 User Manual
Blaupunkt Car Stereo System SEATTLE RDM 169 User Manual
Boss Audio Systems Car Video System bv9565bi User Manual
Breville Blender BBL910XL User Manual
Briggs Stratton Lawn Mower 14 User Manual
Brinkmann Turkey Fryer 815 4001 S User Manual
BRK electronic Smoke Alarm Smoke Alarms User Manual
Cardinal Gates Safety Gate MG15 User Manual
Casio Electronic Keyboard CTK 591 User Manual