Acoustic Energy Speaker AELITE Centre User Manual

Owner’s manual  
 
Connection  
Check that your amplifier is switched off before installing your  
loudspeaker. Failure to do so may result in speaker or amplifier damage.  
The diagram illustrates one loudspeaker only.  
Bi-amping  
Bi-amping adds a second amplifier to the system. One power amplifier  
drives the treble/mid section of both loudspeakers; a second drives the  
bass sections. Note that the shorting links must be removed.  
Failure to do so will result in damaging the amplifiers.  
Conventional  
Normal passive wiring requires shorting links to be in place between the  
treble/mid and bass sections. The positive (ribbed) cable from the  
amplifier positive (or red) terminal should connect with the positive  
(red) terminal on the loudspeaker. Similarly the negative (smooth) cable  
should connect the amplifier negative terminal (black) to the negative  
terminal (black) on the loudspeaker.  
As regards the loudspeakers, wiring for bi-amping is achieved in much  
the same way as bi-wiring. Treble/mid amplifier positive (red) terminals  
should be connected via the ribbed cable to the positive (red) HF  
terminal on the speaker. Similarly, treble/mid amplifier negative is  
connected to the negative (black) HF terminal on the speaker. Repeat  
this process with the bass amplifier and LF terminal pair.  
Bi-wiring  
Bi-wiring separates the bass and treble ground paths in the loudspeaker  
and offer sound quality advantages. An extra set of cables is required.  
Note that the shorting links are removed between the treble/mid and  
bass sections and should be stored for later use if conventional, passive  
driving is required.  
After wiring up  
Lower the volume to the  
minimum, switch on the  
amplifier, select the signal  
source and then raise the  
volume to the  
Two pairs of cables are connected to the amplifier terminals. One cable  
of each pair should connect to the treble/mid section and one to the  
bass section. The positive (ribbed) cables from the amplifier positive (or  
red) terminal should connect with the positive (red) terminals on the  
loudspeaker. Similarly the negative (smooth) cables in each pair should  
connect the amplifier negative terminal (black) to the negative terminals  
(black) on the loudspeaker.  
listening level  
required.  
REAR OF AELITE CENTRE  
RETAIN LINKS  
FOR FUTURE USE  
AMPLIFIER  
CENTRE  
 
Warranty  
Specifications  
HF unit  
Neodymium tweeter with high  
dispersion diaphragm.  
Ferro fluid cooled and damped.  
Magnetically shielded.  
Exclusively profiled. Aluminium front  
plate  
Your Acoustic Energy loudspeakers are guaranteed against original defects in  
materials, manufacture and workmanship for 3 years from the date of  
purchase. Please retain all original packaging materials for possible future use.  
We suggest that you complete details of purchase now and keep this  
information in a safe place for future reference.  
Under this warranty Acoustic Energy agrees to repair any defect or, at the  
companys discretion, replace the faulty component(s) without charge for parts  
or labour. This warranty does not imply any acceptance by Acoustic Energy or  
its agents for consequential loss or damage and specifically excludes fair wear  
and tear, accident, misuse or unauthorised modification.  
LF+MF units  
Crossover  
110mm die-cast chassis. Alloy cone  
with 32mm coil. High-power,  
long-throw magnet system.  
Magnetically shielded.  
@ 155 Hz, 2nd order LF  
@ 2.9 kHz, 3rd order MF  
@ 2.9 kHz, 3rd order HF  
This warranty is applicable in the United Kingdom only and does not in any  
way limit the customers legal rights. Claims and enquiries under the warranty  
for AE products purchased outside the UK should be addressed to the local  
importers or distributors.  
Power Handling  
150W max (undistorted program drive)  
55Hz to 23kHz  
Frequency response 6dB  
Frequency response 3dB  
If you have reason to claim under the warranty please contact your  
dealer in the first instance.  
70Hz to 20kHz  
(on monitor console)  
Sensitivity  
90 dB/W  
Dealers name:........................................................................................................  
Address:....................................................................................................  
.................................................................................................................  
.................................................................................................................  
Date of purchase:....................................................................................................  
Serial numbers:.......................................................................................................  
Impedance  
Cabinet  
8 ohm (4 ohm minimum)  
Real wood veneered. 15 mm MDF wall.  
Dual chamber, high power, low  
turbulence bass reflex port. 22 mm  
MDF front baffle.  
Acoustic Energy Limited  
16 Bridge Road, Cirencester  
Gloucestershire GL7 1NJ  
Tel +44(0)1285 654432  
Terminals  
Gold-plated 4-way binding posts.  
8.0kg  
Weight (excl. packaging)  
Dimensions (WxHxD)  
450 x 190 x 297 mm  
Fax +44(0)1285 654430  
 

Acer Computer Monitor AL2032 User Manual
AEG Cooktop FM 6300G AN User Manual
Airlink101 Switch ASW308 User Manual
Alcatel Carrier Internetworking Solutions Cell Phone 535 735 User Manual
AMD Laptop DA 12241 User Manual
American DJ DJ Equipment Starball II User Manual
Audiovox Car Stereo System ACD 32A User Manual
Avenview Switch SPLIT DVI 2 User Manual
BC Speakers Speaker 18NW100 User Manual
Behringer Microphone C 4 User Manual