AMX Network Card RDA ENC8W User Manual

Installation Sheet  
RDA-ENC8W 8-Module In-Wall Enclosure  
The RDA-ENC8W enclosure provides secure mounting for all AMX  
Lighting, PROlink controllers, and lighting modules. This in-wall enclosure  
mounts between 16" centered studs and provides eight spaces for Radia  
cards, Modules, and Integrated Dimming Modules.  
The unit supports up to 24 dimming channels per unit. This enclosure is UL  
and C-UL approved.  
Install only UL approved models (see the UL Number Cross Reference to  
AMX Lighting ID table on page 2) except RDM-INC and RDm-INC50.  
15.25"  
(387.35 mm)  
14.37"  
SIDE VIEW  
(365.00 mm)  
(with case cover)  
2.25"  
(57.15 mm)  
SIDE VIEW  
37.3"  
(947.4 mm)  
SIDE VIEW  
32.5"  
(825.5 mm)  
Top, side, and bottom  
views are the same for  
this enclosure.  
Metallic stud  
mounting flap  
7.5"  
(190.5 mm)  
3.25"  
(82.55 mm) - located within the wall  
BOTTOM VIEW  
(with case cover)  
BOTTOM VIEW  
(without case cover)  
FIG. 1 Top, bottom and front views of the RDA-ENC8W enclosure  
Radia enclosures must be mounted on a vertical surface with a minimum of  
12" (304.8 mm) clearance above and below the enclosure.  
Installation Instructions:  
For indoor use only.  
Mount on vertical surface only.  
Maintain 16" (406.40 mm) minimum clearance above and below the  
enclosure.  
A to B  
Route class 1 conductors through upper conduit knockouts.  
Route class 2 conductors through lower conduit knockouts.  
Use 75°C (167°F) copper conductors only.  
Supports up to 24 dimming channels per unit (4 RDD-DM6).  
Install filler plate #28-10500 (RDA-EFP) in all unused openings.  
Install only UL approved modules (see the UL Number Cross Refer-  
ence to AMX Lighting ID table on page 2) except RDM-2INC and  
RDM-INC50.  
Top slot  
C to D  
C to D  
Configuration for  
right and left  
mounting brackets  
for all Radia  
enclosures.  
Instals within 16" (406.40 mm) centered studs or surface mount.  
Inserts 3.25" (85.09 mm) into wall to hide conduit (Knockouts  
included).  
G to H  
E to F  
Maximum mounting  
screw size: #12  
Projects 4.25" (107.95 mm) away from wall for ventillation.  
Enclosure Weight:  
RDA-ENC8W: 16.5 lbs. (7.48 kg)  
Dimensions between center lines (from FIG. 2):  
RDA-ENC8W:  
Bottom slot  
A to B = 15.25" (387.35 mm) - Surface mounting  
C to D = 6.00" (152.40 mm) - Stud mounting  
E to F = 32.5" (825.50 mm) - Surface mounting  
G to H = 28.00" (711.20 mm) - Stud mounting  
FIG. 2 Bracket configuration  
 

3Com Cable Box 3CR856 95 User Manual
3Com Network Card 3CRSHEW696 User Manual
ADIC Microscope Magnifier 6 00026 01 Rev A User Manual
Agilent Technologies Video Gaming Accessories 6811B User Manual
Alpine Car Stereo System CDA 7878R User Manual
Alpine GPS Receiver INE NAV 40 User Manual
Altec Lansing Speaker BB2001 User Manual
Altinex Server MT100 102 User Manual
Alto Shaam Air Conditioner 1000 TH III User Manual
American Audio DJ Equipment q d6 User Manual