GENERAL INFORMATION
When doing so, observe the vehicle
manufacturer’s safety notices (airbags,
alarm systems, trip computers, immo-
bilizers).
General information
Thank you for choosing a Blaupunkt
product. We hope you enjoy using this
new piece of equipment.
Before drilling any holes, make sure that
no installed cables or vehicle compo-
nents can be damaged.
Please read these operating instruc-
tions before using the equipment for
the first time.
When installing the signal controller,
select a location in the vehicle that al-
lows you to attach it firmly into place
using screws. The installation location
should be such that the signal control-
ler does not get in the way of the driver
and cannot endanger the occupants in
the event of the vehicle suddenly com-
ing to a halt, for instance, during an
emergency stop.
The Blaupunkt editors are constantly
working on making the operating in-
structions clearer and easier to under-
stand. However, if you still have any
questions on how to operate the device,
please contact your dealer or the tele-
phone hotline for your country. You will
find the telephone number printed at the
back of this booklet.
We provide a manufacturer guarantee
for our products bought within the Eu-
ropean Union. You can view the guar-
antee conditions at www.blaupunkt.de
or ask for them directly at:
The IR remote control should not be in-
stalled within the inflation range of air-
bags (driver, passenger side, side air-
bags) or in any position where it could
be struck by the vehicle occupants’
heads or knees.
Blaupunkt GmbH
Hotline
Robert Bosch Str. 200
With regard to the installation location
and the attachment using an adhesive
pad, check and ensure that the holding
strength of the installation surface is
sufficient and suitable for all situations
and safety requirements.
D-31139 Hildesheim
Installation and safety notices
Before connecting your signal control-
ler, please read the following informa-
tion carefully.
Accessories
We recommend you use accessories
that have been approved by Blaupunkt.
The battery’s negative terminal must
be disconnected for the entire time
it takes to install and connect this de-
vice.
11
SUPPLIED PARTS
Supplied parts
SWITCHING ON/OFF
Switching on/off
The signal controller is supplied with all
the parts listed below. Please check that
the range of parts supplied with your
device is complete. If one of the listed
parts is missing, please contact your
dealer immediately.
Switching on the signal
controller
The signal controller is switched on via
the “+12V ignition” switching line by the
connected control device.
Switching off the signal
controller
● Signal controller 7 607 003 551
The signal controller is switched off via
the “+12V ignition” switching line by the
connected control device.Switching on/
off.
● Connecting cable
● Screws
● IR remote control
● IR receiver
● Operating and installation instruc-
tions
12
SETTINGS
IR REMOTE CONTROL
IR remote control
Functions
Settings
External monitor switch (Fig. 2)
Switch position on right: No external The supplied remote control is suitable
monitor connected.
for operating the signal controller and
the monitors.
Switch position on left: If a Blaupunkt
navigation (RGB) monitor is connected You must enter a button combination
via a Y-cable (7 607 001 600).
in order to control a single monitor
or all the monitors simultaneously.
To do so, you first select the monitor
(FRONT/LEFT/RIGHT-OVERHEAD or
ALL) and then the function that you
require. The selected monitor or
monitors remain(s) selected until you
press one of the buttons (FRONT/
LEFT/RIGHT-OVERHEAD or ALL)
again.
Monitor connections
Note: From the FRONT, LEFT, RIGHT
and OVERHEAD monitor output, you
can optionally assign the 8 or 13 PIN
jack.
1
NAVI
POWER
MUTE
4
5
<
AUDIO CH
BOOSTER
VOL
CH
;
:
FRONT
LEFT
9
8
ALL
RIGHT
OVERHEAD
IVRC 05
7
13
IR REMOTE CONTROL
1 POWER
Settings for Audio OUT
; AUDIO CH • Arrow button
On/off button for the selected
monitor or monitors.
/
Select the input source for Audio
OUT.
2 NAVI
Selects the navigation monitor.
Note: The volume of the input
source must be adjustable.
3 VOL • arrow button
Increase the volume for the se-
lected monitor (not Audio OUT).
< BOOSTER
Setting the amplification for Audio
OUT 0 dB or 10 dB.
/
VOL • arrow button
Decrease the volume for the se-
lected monitor (not Audio OUT).
4 MUTE
Mute the volume for all the con-
nected monitors and Audio OUT.
5 CH • arrow button
/
Select the input source for the se-
lected monitor.
6 RIGHT
Selects the right monitor.
7 OVERHEAD
Selects the overhead monitor.
8 ALL
Select all monitors.
9 LEFT
Select the left monitor.
: FRONT
Select the front monitor.
14
INSTALLATION
Note:
Installation
Before connecting the monitors to
your signal controller, check that the
+/- and switching positive connec-
tions are working properly.
Installation and safety notices
Before connecting your signal control-
ler, please read the following informa-
tion carefully.
Positive connection
The battery’s negative terminal must
be disconnected for the entire time it
takestoinstallandconnectthisdevice.
Connect the fuse holder (1A fuse) to
protect the positive cable (permanent
(1), see Fig. 1). The fuse holder should
be connected to the positive terminal at
a distance of max. 30 cm from the vehi-
cle battery (if necessary, drill a hole in
the bulkhead and use the appropriate
cable grommets).
When doing so, observe the vehicle
manufacturer’s safety notices (airbags,
alarm systems, trip computers, immo-
bilizers).
Before drilling any holes, make sure that
no installed cables or vehicle compo-
nents can be damaged.
Switching positive
Connect the switching positive cable (2)
(see Fig. 1) to the switching positive
When installing the signal controller,
select a location in the vehicle that al-
lows you to attach it firmly into place
using screws. The installation location
should be such that the signal control-
ler does not get in the way of the driver
and cannot endanger the occupants in
the event of the vehicle suddenly com-
ing to a halt, for instance, during an
emergency stop.
output (ignition
) of the main de-
vice (e.g. car radio or navigation device).
If connecting to terminal 15 of the vehi-
cle, protect the switching positive cable
(2) by installing a fuse holder (1A fuse)
at a maximum distance of 20 cm from
the point of connection.
Fuse
The IR remote control should not be in-
stalled within the inflation range of air-
bags (driver, passenger side, side air-
bags) or in any position where it could
be struck by the vehicle occupants’
heads or knees.
If the fuse needs to be replaced, never
bypass/bridge the fuse and never re-
place it with fuse types that are designed
for higher currents.
Negative (ground) connection
With regard to the installation location
and the attachment using an adhesive
pad, check and ensure that the holding
strength of the installation surface is
sufficient and suitable for all situations
and safety requirements.
Attach the negative cable (1) (earth/
GND, (3), see Fig. 1) directly to the ve-
hicle body using a screw. Scratch the
surface down to the bare metal at the
point at which the ground is made.
•
If the installation requires holes to be
drilled or any other changes to be
15
INSTALLATION
SPECIFICATIONS
made to the vehicle, please contact
a specialist workshop in your area.
Specifications
Video input:
Composite Video, 1.0 Vpp, 75 ohms
Note:
You cannot display PAL video on the
wide vision TV monitor using the RGB
input.
Audio input:
0 - 1.0 Vrms, 20 Hz-20 kHz
(Booster off)
In this case, the PAL video signal must
be connected directly to the AV input of
the wide vision TV monitor..
0 - 0.3 Vrms, 20 Hz-20 kHz
(Booster on)
RGB input (video signal):
0.7 VPP, 75 ohms
RGB input (composite-sync):
0.7 VPP, 75 ohms
Video output:
Composite video, 1.0 Vp-p, 75 ohms
Audio output:
0 - 1.0 Vrms, 20 Hz - 20 kHz
RGB output (video signal):
0.7 VPP, 75 ohms
RGB output (composite-sync):
1.0 VPP, 75 ohms
Power supply:
DC 12V, +/- 10%, max. 5A
Operating temperature:
-20° to +70° Celsius
Dimensions:
205 x 45 x 146 mm (W x H x D)
16
SPECIFICATIONS
Features
5 Audio inputs:
Cinch jacks
4 Video inputs:
Cinch jacks
1 RGB input:
15 pin Sub-D socket
4 monitor outputs:
Composite video, audio L/R, control,
13-pin (8-pin) jack, with power, earth
and switching positive
1 RGB output:
15-pin Sub-D plug-type connector
1 Audio output:
Cinch jacks
10dB booster on/off
Conversion:
RGB to CCVS
CCVS to RGB
IR remote control
IR receiver
Power input:
4-pin plug-type connector
Metal housing
17
Anschlussbilder • Connection diagrams • Schéma
électrique • Schemi di allacciamento • Aansluittekeningen •
Anslutningsbilder • Esquemas de conexión • Esquemas de
ligação • Tilslutningsskemaer
12V
Fig. 1
Ext-monitor IR
CH5
CH1
CH3
CH4
DC 12V IN
RGB-IN
AUDIO-IN
CH2
+12V Ignition
+12V Permanent
(Batterie, battery)
(2)
(1)
(3)
Masse / GND
72
Fig. 2
Ext-monitor IR
CH5
CH1
CH2
CH3
CH4
DC 12V IN
RGB-IN
AUDIO-IN
IR-Empfänger (Eingang)
IR receiver in
Audio in-right
Audio in-left
Video in
Externer Monitorschalter
Fig. 3
Audio OUT
RGB OUT
R
L
FRONT LEFT
RIGHT OVERHEAD
(right)
(left)
Audio OUT
MONITOR
MONITOR
MONITOR
MONITOR
Navi- Monitor
IVMS 5802
IVMS 6502
IVMR 9002
IVMR 1042
73
I V M R 9 0 0 2 / 1 0
I V M S 5 8 0 2 / 6 5
V i d e o o u t
u d A i o R o u t
u d A i o L o u t
o l l e r I V S C - 5 S 5 i 0 g 2 n a l C o n t r
74
Service-Nummern / Service numbers / Numéros du service après-
vente / Numeri del servizio di assistenza / Servicenummers /
Telefonnummer för service / Números de servicio / Números de
serviço / Servicenumre
Country:
Phone:
Fax:
WWW:
Germany
(D)
0180-5000225
05121-49 4002
Austria
(A)
(B)
01-610 390
02-525 5454
01-610 393 91
02-525 5263
44-898 644
09-435 99236
01-4010 7320
01-89583 8394
210 57 69 473
01-4598830
02-369 6464
40 2085
023-565 6331
66-817 157
01-2185 11111
916-467952
08-7501810
01-8471650
Belgium
Denmark
Finland
France
(DK) 44 898 360
(FIN) 09-435 991
(F)
01-4010 7007
Great Britain (GB) 01-89583 8880
Greece
Ireland
Italy
Luxembourg (L)
Netherlands (NL)
Norway
Portugal
Spain
(GR) 210 57 85 350
(IRL) 01-4149400
(I)
02-369 6331
40 4078
023-565 6348
66-817 000
01-2185 00144
902-120234
08-7501500
(N)
(P)
(E)
(S)
Sweden
Switzerland (CH) 01-8471644
Czech. Rep. (CZ)
02-6130 0441
01-333 9575
0800-118922
02-6130 0514
01-324 8756
022-8771260
Hungary
Poland
(H)
(PL)
Turkey
USA
(TR)
0212-3350677
0212-3460040
708-6817188
(USA) 800-2662528
Brasil
(Mercosur)
(BR) +55-19 3745 2769 +55-19 3745 2773
Malaysia
(Asia Pacific) (MAL) +604-6382 474
+604-6413 640
Blaupunkt GmbH
07/03
CM/PSS - 8 622 403 778
|