User Manual
EUROLIVE
VS1520/VS1220F/VS1220
High-Performance 600-Watt PA Speaker with
15"/12" Woofer and Electro-Dynamic Driver
3
EUROLIVE VS1520/VS1220F/VS1220 User Manual
9. Do not defeat the safety purpose of the polarized
UNDERTAKING OR REPRESENTATION. THIS MANUAL
IS COPYRIGHTED. NO PART OF THIS MANUAL MAY
BE REPRODUCED OR TRANSMITTED IN ANY FORM
OR BY ANY MEANS, ELECTRONIC OR MECHANICAL,
Important Safety
Instructions
or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the INCLUDING PHOTOCOPYING AND RECORDING OF ANY
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
KIND, FOR ANY PURPOSE, WITHOUT THE EXPRESS
WRITTEN PERMISSION OF MUSIC GROUP IP LTD.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
ALL RIGHTS RESERVED.
© 2012 MUSIC Group IP Ltd.
Trident Chambers, Wickhams Cay, P.O. Box 146,
Road Town, Tortola, British Virgin Islands
Terminals marked with this symbol carry
electrical current of sufficient magnitude
to constitute risk of electric shock.
11. Use only attachments/accessories specified by
the manufacturer.
Use only high-quality professional speaker cables with
¼" TS or twist-locking plugs pre-installed. All other
installation or modification should be performed only
by qualified personnel.
12. Use only with the
cart, stand, tripod, bracket,
or table specified by the
LIMITED WARRANTY
§ 1 Warranty
manufacturer, or sold with (1) This limited warranty is valid only if you purchased
the apparatus. When a cart the product from a MUSIC Group Authorized Reseller in
This symbol, wherever it appears,
alerts you to the presence of uninsulated
dangerous voltage inside the
is used, use caution when
the country of purchase. A list of authorized resellers can
moving the cart/apparatus be found on BEHRINGER’s website behringer.com under
enclosure - voltage that may be sufficient to constitute a
risk of shock.
combination to avoid
“Where to Buy”, or you can contact the MUSIC Group office
closest to you.
injury from tip-over.
This symbol, wherever it appears,
alerts you to important operating and
maintenance instructions in the
13. Unplug this apparatus during lightning storms or
(2) MUSIC Group* warrants the mechanical and
when unused for long periods of time.
electronic components of this product to be free of defects
in material and workmanship if used under normal
operating conditions for a period of one (1) year from
the original date of purchase (see the Limited Warranty
terms in § 4 below), unless a longer minimum warranty
period is mandated by applicable local laws. If the product
shows any defects within the specified warranty period
and that defect is not excluded under § 4, MUSIC Group
shall, at its discretion, either replace or repair the product
using suitable new or reconditioned product or parts.
In case MUSIC Group decides to replace the entire product,
this limited warranty shall apply to the replacement
product for the remaining initial warranty period, i.e.,
one (1) year (or otherwise applicable minimum warranty
period) from the date of purchase of the original product.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has
been dropped.
accompanying literature. Please read the manual.
Caution
To reduce the risk of electric shock, do not
remove the top cover (or the rear section).
No user serviceable parts inside. Refer servicing to
qualified personnel.
Caution
To reduce the risk of fire or electric shock,
do not expose this appliance to rain and
15. The apparatus shall be connected to a MAINS socket
outlet with a protective earthing connection.
16. Where the MAINS plug or an appliance coupler is
used as the disconnect device, the disconnect device shall
remain readily operable.
moisture. The apparatus shall not be exposed to dripping
or splashing liquids and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
Caution
These service instructions are for use
by qualified service personnel only.
(3) Upon validation of the warranty claim, the repaired
or replacement product will be returned to the user
freight prepaid by MUSIC Group.
To reduce the risk of electric shock do not perform any
servicing other than that contained in the operation
instructions. Repairs have to be performed by qualified
service personnel.
(4) Warranty claims other than those indicated above
are expressly excluded.
PLEASE RETAIN YOUR SALES RECEIPT. IT IS YOUR PROOF
OF PURCHASE COVERING YOUR LIMITED WARRANTY.
THIS LIMITED WARRANTY IS VOID WITHOUT SUCH PROOF
OF PURCHASE.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
LEGAL DISCLAIMER
TECHNICAL SPECIFICATIONS AND APPEARANCES
ARE SUBJECT TO CHANGE WITHOUT NOTICE AND
ACCURACY IS NOT GUARANTEED. BEHRINGER IS
PART OF THE MUSIC GROUP (MUSIC-GROUP.COM).
ALL TRADEMARKS ARE THE PROPERTY OF THEIR
RESPECTIVE OWNERS. MUSIC GROUP ACCEPTS NO
LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED
BY ANY PERSON WHO RELIES EITHER WHOLLY OR
IN PART UPON ANY DESCRIPTION, PHOTOGRAPH
OR STATEMENT CONTAINED HEREIN. COLORS AND
SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT.
MUSIC GROUP PRODUCTS ARE SOLD THROUGH
AUTHORIZED FULLFILLERS AND RESELLERS ONLY.
FULLFILLERS AND RESELLERS ARE NOT AGENTS OF
MUSIC GROUP AND HAVE ABSOLUTELY NO AUTHORITY
TO BIND MUSIC GROUP BY ANY EXPRESS OR IMPLIED
§ 2 Online registration
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
Please do remember to register your new BEHRINGER
equipment right after your purchase at behringer.com
under“Support”and kindly read the terms and conditions
of our limited warranty carefully. Registering your
purchase and equipment with us helps us process
your repair claims quicker and more efficiently.
Thank you for your cooperation!
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
§ 3 Return materials authorization
(1) To obtain warranty service, please contact the
retailer from whom the equipment was purchased.
Should your MUSIC Group Authorized Reseller not be
located in your vicinity, you may contact the MUSIC Group
Authorized Fulfiller for your country listed under
4
EUROLIVE VS1520/VS1220F/VS1220 User Manual
“Support”at behringer.com. If your country is not
listed, please check if your problem can be dealt with
by our“Online Support”which may also be found under
“Support”at behringer.com. Alternatively, please submit
an online warranty claim at behringer.com BEFORE
returning the product. All inquiries must be accompanied
by a description of the problem and the serial number
of the product. After verifying the product’s warranty
eligibility with the original sales receipt, MUSIC Group
will then issue a Return Materials Authorization
(“RMA”) number.
•
connection or operation of the unit in any way
that does not comply with the technical or safety
regulations applicable in the country where the
product is used;
(3) This warranty does not detract from the seller’s
obligations in regard to any lack of conformity of the
product and any hidden defect.
§ 9 Amendment
•
damage/defects caused by acts of God/Nature
(accident, fire, flood, etc) or any other condition that
is beyond the control of MUSIC Group.
Warranty service conditions are subject to change without
notice. For the latest warranty terms and conditions
and additional information regarding MUSIC Group’s
limited warranty, please see complete details online at
behringer.com.
(7) Any repair or opening of the unit carried out by
unauthorized personnel (user included) will void the
limited warranty.
* MUSIC Group Macao Commercial Offshore Limited of
Rue de Pequim No. 202-A, Macau Finance Centre 9/J, Macau,
including all MUSIC Group companies
(8) If an inspection of the product by MUSIC Group
shows that the defect in question is not covered by the
limited warranty, the inspection costs are payable by
the customer.
(2) Subsequently, the product must be returned in
its original shipping carton, together with the return
authorization number to the address indicated by
MUSIC Group.
(9) Products which do not meet the terms of this
limited warranty will be repaired exclusively at the buyer’s
expense. MUSIC Group or its authorized service center will
inform the buyer of any such circumstance. If the buyer
fails to submit a written repair order within 6 weeks after
notification, MUSIC Group will return the unit C.O.D. with
a separate invoice for freight and packing. Such costs will
also be invoiced separately when the buyer has sent in a
written repair order.
(3) Shipments without freight prepaid will not
be accepted.
§ 4 Warranty Exclusions
(1) This limited warranty does not cover consumable
parts including, but not limited to, fuses and batteries.
Where applicable, MUSIC Group warrants the valves or
meters contained in the product to be free from defects
in material and workmanship for a period of ninety (90)
days from date of purchase.
(10) MUSIC Group Authorized Resellers do not sell new
products directly in online auctions. Purchases made
through an online auction are on a“buyer beware”basis.
Online auction confirmations or sales receipts are not
accepted for warranty verification and MUSIC Group will
not repair or replace any product purchased through an
online auction.
(2) This limited warranty does not cover the product
if it has been electronically or mechanically modified
in any way. If the product needs to be modified or
adapted in order to comply with applicable technical
or safety standards on a national or local level, in any
country which is not the country for which the
product was originally developed and manufactured,
this modification/adaptation shall not be considered a
defect in materials or workmanship. This limited warranty
does not cover any such modification/adaptation,
regardless of whether it was carried out properly or not.
Under the terms of this limited warranty, MUSIC Group
shall not be held responsible for any cost resulting from
such a modification/adaptation.
§ 5 Warranty transferability
This limited warranty is extended exclusively to the
original buyer (customer of authorized reseller) and is
not transferable to anyone who may subsequently
purchase this product. No other person (reseller, etc.)
shall be entitled to give any warranty promise on behalf
of MUSIC Group.
(3) This limited warranty covers only the product
hardware. It does not cover technical assistance for
hardware or software usage and it does not cover
any software products whether or not contained in
the product. Any such software is provided“AS IS”
unless expressly provided for in any enclosed software
limited warranty.
§ 6 Claim for damage
Subject only to the operation of mandatory applicable
local laws, MUSIC Group shall have no liability to the buyer
under this warranty for any consequential or indirect
loss or damage of any kind. In no event shall the liability
of MUSIC Group under this limited warranty exceed the
invoiced value of the product.
(4) This limited warranty is invalid if the
factory-applied serial number has been altered or
removed from the product.
§ 7 Limitation of liability
This limited warranty is the complete and exclusive
warranty between you and MUSIC Group. It supersedes
all other written or oral communications related to this
product. MUSIC Group provides no other warranties for
this product.
(5) Free inspections and maintenance/repair work
are expressly excluded from this limited warranty,
in particular, if caused by improper handling of the
product by the user. This also applies to defects caused
by normal wear and tear, in particular, of faders,
crossfaders, potentiometers, keys/buttons, guitar strings,
illuminants and similar parts.
§ 8 Other warranty rights and
national law
(1) This limited warranty does not exclude or limit the
buyer’s statutory rights as a consumer in any way.
(6) Damage/defects caused by the following conditions
are not covered by this limited warranty:
(2) The limited warranty regulations mentioned herein
are applicable unless they constitute an infringement of
applicable mandatory local laws.
•
improper handling, neglect or failure to operate the
unit in compliance with the instructions given in
BEHRINGER user or service manuals;
5
EUROLIVE VS1520/VS1220F/VS1220 User Manual
1. Before You Get Started
1.1 Shipment
Your VS series loudspeaker was carefully packed at the assembly plant to assure
secure transport. Should the condition of the cardboard box suggest that damage
may have taken place, please inspect the unit immediately and look for physical
indications of damage.
!!
Caution
Never connect multiple power amps to one loudspeaker. Doing so could cause
the very fabric of reality to unravel, sending the entire universe into oblivion.
Worse yet, it could destroy your amplifiers and loudspeaker.
5. Turn the sound source on (mixer, stereo, etc.).
◊
Damaged equipment should NEVER be sent directly to us. Please inform 6. Make sure the volume/gain control on the power amp is turned all the way
the dealer from whom you acquired the unit immediately as well
as the transportation company from which you took delivery.
Otherwise, all claims for replacement/repair may be rendered invalid.
down, and then turn the power on.
7. Activate the sound source, whether it is playing music from a CD player or
speaking into a microphone, and adjust the levels. Gradually raise the power
amp volume level to desirable level. If distortion occurs, turn the power
amp volume down. Should the problem persist, make sure distortion is not
occurring at the sound source. If you reach the desired volume level by barely
turning up the power amp level/gain, turn the sound source output down to
allow the power amp to push the speakers more.
◊
◊
◊
Please always use the original packaging to avoid damage due to
storage or shipping.
Never let unsupervised children play with the loudspeaker or
with its packaging.
Please dispose of all packaging materials in an environmentally
friendly fashion.
8. Rock ‘n Roll!
1.2 Online registration
Please register your new BEHRINGER equipment right after your purchase
warranty carefully.
2. Connections
(1)
Should your BEHRINGER product malfunction, it is our intention to
have it repaired as quickly as possible. To arrange for warranty service,
please contact the BEHRINGER retailer from whom the equipment was
purchased. Should your BEHRINGER dealer not be located in your vicinity,
you may directly contact one of our subsidiaries. Corresponding contact
information is included in the original equipment packaging (Global Contact
Information/European Contact Information). Should your country not be listed,
please contact the distributor nearest you. A list of distributors can be found in
the support area of our website (http://behringer.com).
Fig. 2.1: Connector panel
(1) The VS series features two parallel ¼" TS loudspeaker inputs. You can
connect one of the connectors to the output on your power amp and tap
into the signal from the amp on the second connector, in order, for example,
to feed this signal into an additional loudspeaker.
Registering your purchase and equipment with us helps us process your repair
claims more quickly and efficiently.
Thank you for your cooperation!
1.3 Basic operation
Using the VS series loudspeakers is easy and intuitive. Simply follow these steps
to achieve the best possible sound:
1. Plug the line-level outputs from a sound source such as a mixer or stereo
system into a power amp of appropriate size (see 4.2 Power amp rating).
Make sure the sound source and amplifier are turned off.
2. Using ¼" TS speaker cables, plug the power amp output into the ¼" input on
the back of the speaker. DO NOT use instrument cables (i.e., guitar cords) for
this connection!
Fig. 2.2: ¼" TS loudspeaker connector
3. If using a pair of VS loudspeakers, run the amp in stereo operation.
If using just one loudspeaker, mono operation is preferable.
◊
◊
ATTENTION: Never connect the output signals of different power
amps to both parallel inputs at the same time. This may permanently
damage your equipment.
4. If using four or more loudspeakers, there are a few ways to make the
connections. The first is to use two power amps, one for each pair. Another is
to connect the first pair of loudspeakers in normal stereo operation, then use
the ¼" output jacks on the back of the loudspeakers to link the second pair
of loudspeakers. This way each channel on the power amp is driving two
loudspeakers. Make sure that the wattage and ohm rating are appropriate
for this situation.
When several loudspeakers are wired in parallel, the overall impedance
Z
T
to be handled by the power amp can be calculated, as shown here,
from the individual impedance values of the connected speakers:
1
=
ZT
+
+
1⁄Z 1⁄Z
....
1
2
6
EUROLIVE VS1520/VS1220F/VS1220 User Manual
For the VS series, here are typical connection scenarios:
3.4 Loudspeaker protection by using a
low-cut filter
•
Two 8 Ohm speakers in parallel = 4 Ohms
Four 8 Ohm speakers in parallel = 2 Ohms
Two 4 Ohm speakers in parallel = 2 Ohms
Four 4 Ohm speakers in parallel = 1 Ohm
Try to prevent damage to your loudspeakers caused by extreme oscillation
of the low-frequency driver due to subsonic noise and extremely deep
frequencies. Use an equalizer to cut off those frequencies that fall below
your loudspeakers’ frequency range, or use a low-cut/high-pass filter.
Most equalizers and sound-improvement systems offer a low-cut function,
like the BEHRINGER ULTRAGRAPH DIGITAL DEQ1024, for example. Using a low-cut
filter in your signal path is particularly recommended if you use record players
or CD players as your signal source. CD players often produce extremely deep
frequencies, which can lead to extreme excursions of the low-frequency driver.
•
•
•
◊
Your amplifier may be damaged if the actual impedance drops below
its input impedance. Please make sure that the calculated total
impedance ZT is not smaller than the minimum impedance specified
for your amplifier.
3. Optimal Operation
4. Additional Considerations
We have developed the VS series for use in a wide range of possible applications.
Of course, the sound of your loudspeakers depends on the acoustic characteristics
of the room/space in which they are being used. The following chapters of
this manual will give you information about getting the most out of your
EUROLIVE loudspeakers.
4.1 Length and diameter of loudspeaker cables
Loudspeaker cables whose diameter is too small can considerably limit the
power amp performance. The longer the cable, the more pronounced the
problem. As a result, musicians often simply “turn up” the amp, which can lead
to loudspeaker damage. Therefore, don’t use cables longer than 15 m (45 ft.).
For most applications, this will not be necessary. Cable diameter should be at
least 14 - 12 gauge.
3.1 Loudspeaker placement
Here are some tips to get optimal sound and performance from
your loudspeaker(s):
4.2 Power amp rating
•
Elevate the loudspeaker at or above head level. High frequencies are
the segment of the audio spectrum responsible for clarity and speech
intelligibility. They can get muffled by the front row of the audience,
so we recommend positioning your loudspeakers so the high-frequency
drivers are slightly above the height of the audience. The more you can get
everyone in direct earshot, the better. Imagine the loudspeaker is a giant
flashlight, and you want to illuminate everyone in the room
Selecting the right amp can turn out to be rather difficult. Therefore, stick to
the following rule of thumb: the power rating of your amp should be roughly
twice the loudspeaker load capacity. A loudspeaker rated at 200 Watts
continuous performance can easily be powered by an amp rated at 400 Watts
output power. An optimal addition to your speaker system would be the
BEHRINGER EUROPOWER EP2000 power amp, for example.
•
Avoid placing full-range loudspeakers in a corner or right next to a wall.
This enhances the low frequencies and can cause the sound to get muddy.
Subwoofers may be placed almost anywhere since low frequencies are not
highly directional
4.3 Fuses
We do not recommend the use of fuses with loudspeaker applications. Damage to
loudspeakers can be the result of high peak signals and high output power.
However, fuses can only offer protection from one of these two factors, and never
from both. Additionally, fuse resistances are sometimes nonlinear, leading to
distortion and unpredictable overdriving.
•
•
Make sure that the loudspeakers are not in a place where they could
be knocked over by dancing audience members, overly eccentric stage
performers, sudden earthquakes, etc.
4.4 Protecting your equipment
Some rooms, such as gymnasiums and auditoriums, create a large amount
of natural reverb, making it difficult to maintain intelligible sound.
Laying carpet or rugs on the ground and curtains across windows or
brick walls will help dampen the reflections and improve the overall sound
•
•
•
Always try to find the optimal signal level. Avoid overdriving your amp
Keep in mind the physical limitations of your PA system
Use a limiter to restrict the output signal level. Place the limiter
between the mixing console and the power amp. For this purpose,
our proven AUTOCOM PRO-XL MDX1600, COMPOSER PRO-XL MDX2600 and
MULTICOM PRO-XL MDX4600 compressors offer an outstanding solution.
All models can be used as a limiter: the audio signal doesn’t overdrive any
more, and unpleasant “peaks” are effectively avoided
3.2 How to prevent feedback
Always place the “front of house” speakers ahead of the microphones
(from the audience’s perspective), and never behind. Use professional floor
monitors or an in-ear monitoring system to allow the stage performers to hear.
3.3 How to avoid feedback when working with
record players (DJ Applications)
◊
Our ULTRADRIVE PRO DCX2496 and SUPER-X CX3400/CX2310 crossovers
are particularly well-suited for protecting your equipment: for each
output, they have independent limiters.
In applications with record players, bass feedback can occur. Bass feedback
occurs when low frequencies get back to the pickup and are reproduced on the
loudspeakers. The most common causes for this are: speakers located too closely
to the record player, a room with a wooden floor, or presence of a podium or a
platform. In such cases, it is best to move the loudspeakers away from the record
player and remove them from the stage, so that they are located on firm ground.
Another option is to use raised stands, which prevent the loudspeakers from
having a direct contact with the ground.
7
EUROLIVE VS1520/VS1220F/VS1220 User Manual
5. Application Examples
5.1 Full-range stereo operation
In this example, the main output signal of a mixing console is connected
to a power amplifier. Both the outputs and inputs are stereo. A full-range
VS series loudspeaker is connected to each of the amplifier outputs,
and these loudspeakers reproduce the entire frequency range.
5.3 Two-way stereo operation with a crossover,
full-range loudspeakers and subwoofers
Using an external active crossover, the main output signal of a mixing console is
split into two signals. One signal covers the lower frequency range and the other
signal covers the mid and high frequency range. The recommended crossover
frequency is 150 Hz. Then, the mid-high frequency signal is connected to a stereo
power amplifier. A VS series loudspeaker is connected to each of the amplifier
outputs. The low-frequency signal is connected to an additional power amplifier,
which powers two subwoofers.
VS1520
V
XENYX 1202FX
XENYX 1202FX
L
R
L
R
EP2000
SUPER-X PRO
CX2310
L
R
L
R
Fig. 5.1: Full-range stereo operation
5.2 Full-range stereo operation with
floor monitors
EP2000
This example is a variation of the example above, with the addition of several
VS1220F floor monitors. Two separate monitor outputs from the mixing console
are connected to the inputs of a stereo power amplifier. A VS1220F is connected
to each amplifier output, and a second VS1220F is connected to the parallel
outputs of the first set of VS1220F monitors.
VS1220
X2442USB
VP1800S
AUX 2
SEND
Fig. 5.3 Two-way stereo operation with subwoofers
L
R
AUX 1
SEND
EP2000
VS1220
VP1220F
Fig. 5.2 Full-range stereo operation with floor monitors
8
EUROLIVE VS1520/VS1220F/VS1220 User Manual
6. Specifications
VS1520
VS1220F
System Data
System Data
Continuous Power (IEC 60268-5) 150 W
Continuous Power (IEC 60268-5) 150 W
Peak Power
600 W
Peak Power
600 W
Type
2-way full-range loudspeaker
50 Hz – 20 kHz
8 Ohms
Type
2-way full-range loudspeaker
55 Hz – 20 kHz
Frequency Response
Impedance
Frequency Response
Impedance
8 Ohms
Sound Pressure Level (SPL)
Dispersion
94 dB (Full space, 1 W @ 1 m)
80° x 40°
Sound Pressure Level (SPL)
Dispersion
93 dB (Full space, 1 W @ 1 m)
80° x 40°
Crossover Frequency
Rigging Fittings
3.0 kHz
Crossover Frequency
Rigging Fittings
3.5 kHz
ergonomically shaped handle;
integral tripod/stand adapter
ergonomically shaped handle
Components
Components
HF Driver
LF Driver
Dual electro-dynamic drivers
12" / 307 mm
HF Driver
LF Driver
Dual electro-dynamic drivers
15" / 385 mm
Dimensions/Weight
Dimensions/Weight
Width
Height
Depth
Weight
17.3" / 440 mm
16.9" / 430 mm
22.6" / 575 mm
34.2 lbs / 15.5 kg
Width
Height
Depth
Weight
17.9" / 455 mm
27.0" / 685 mm
18.3" / 465 mm
48.3 lbs / 21.9 kg
9
EUROLIVE VS1520/VS1220F/VS1220 User Manual
VS1220
System Data
Continuous Power (IEC 60268-5) 150W
Peak Power
600 W
Type
2-way full-range loudspeaker
60 Hz – 20 kHz
8 Ohms
Frequency Response
Impedance
Sound Pressure Level (SPL)
Dispersion
93 dB (Full space, 1 W @ 1 m)
80° x 40°
Crossover Frequency
Rigging Fittings
3.5 kHz
ergonomically shaped handle;
integral tripod/stand adapter
Components
HF Driver
LF Driver
Dual electro-dynamic drivers
12" / 307 mm
Dimensions/Weight
Width
Height
Depth
Weight
14.6" / 370 mm
23.6" / 600 mm
16.9" / 430 mm
37.7 lbs / 17.1 kg
BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts,
modifications may be made from time to time to existing products without prior notice. Specifications and
appearance may differ from those listed or illustrated.
11 EUROLIVE VS1520/VS1220F/VS1220 User Manual
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
EUROLIVE VS1520/VS1220F/VS1220
Responsible Party Name:
Address:
MUSIC Group Services US Inc.
18912 North Creek Parkway,
Suite 200 Bothell, WA 98011,
USA
Phone/Fax No.:
Phone: +1 425 672 0816
Fax: +1 425 673 7647
EUROLIVE VS1520/VS1220F/VS1220
complies with the FCC rules as mentioned in the following paragraph:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by MUSIC Group
can void the user’s authority to use the equipment.
We Hear You
|