Tech 21 Stereo Amplifier GT2 User Manual

POWER REQUIREMENTS  
Utilizes standard 9V alkaline battery (not included).To install,simply remove battery door.  
(NOTE:The Input activates battery.To conserve energy, unplug when not in use.)  
Power Consumption: approx.4mA.  
USE DC POWER SUPPLYONLY!  
DC Power Supply Specifications:  
Failure to do so may damage the unit and void warranty.  
-9V DC regulated or unregulated,100mA minimum;  
-2.1mm female plug,center negative (-).  
Optional factory po wer supply is available , Model #DC2.  
WARNINGS:  
Attempting to repair unit is not recommended and may void warranty.  
Missing or altered serial numbers automatically void warranty. For your own protection,be sure  
serial number labels on the unit’s back plate and exterior box are intact.  
ONE YEAR LIMITED WARRANTY . PROOF OF PURCHASE REQUIRED  
.
Manufacturer warrants unit to be free from defects in materials and workmanship for one (1) year  
from date of purchase to the original purchaser and is not transferable.This warranty does not include  
damage resulting from accident,misuse, abuse, alteration,or incorrect current or voltage. If unit be-  
comes defective within warranty period, Tech 21 will elect to repair or replace it free of charge.After  
warranty expires,Tech 21 will repair defective unit for a fee.  
ALL REPAIRS for residents of U.S.Call Tech 21 for Return Authorization Number  
. Manufacturer  
will not accept packages without prior authorization,pre-paid freight (UPSpreferred) and proper insur-  
ance. International purchasers should contact the authorizedTech 21 distributor in their particular  
country.  
FOR PERSONAL ASSISTANCE & SERVICE:  
Contact Tech 21,Inc., weekdays from 9:00 AM to 5:00 PM,EST.  
OWNER’S MANUAL  
DESIGNED AND MANUF ACTURED IN THE U.S.A.  
© 1993 Tech 21,Inc.  
 
UNIVERSAL OUTPUT  
Another aspect of the technological advancement of SansAmp, is a single output that is physically com-  
patible for an y application.SansAmp’s Universal Output makes it possible to use the same output with  
the following:  
FULL RANGE(HiFi):  
Tape  
LIMITED RANGE (LoFi):  
Rack Systems  
Studio Monitors  
P.A.  
Stereo  
Pre-Amps  
Head &Cabinet  
Combos  
Practice Amps  
OTHER INSTRUMENTS & APPLICATIONS  
Be creative! SansAmp GT2 is not just for guitar.Try other instruments:bass, keyboards,drums,sax,  
vocals,etc. (Just remember to be aware of the input signal level as noted previously.) Also try using  
SansAmp GT2 in other applications,such as in mixdowns to liven up existing tracks.  
For experimentation,start with a clean,flat setting:  
•Set all 3 Character Switches at the bottom position.  
•Set Knob Controls: Low and High at 11 o’clock  
Drive and Level at 12 o’clock  
Adjust EQ and gain structure to taste.  
NOTEWORTHY NOTES & SUGGESTIONS  
1. SansAmp GT2 is an interactive tool.It will react differently to various signal levels,as well as your  
individual touch. For instance, a hotter signal and a heavy hand will increase the gain structure and result  
in more overdrive.A cooler signal and a light touch decreases gain structure for a cleaner sound.  
2. SansAmp GT2 has a very low noise level.If you experience noise, be aware of the following:  
-SansAmp GT2 may be amplifying noise emanating from the input source.  
-Check for pickup interference by moving guitar or turning the volume off.NOTE:Single coil pic-  
ups are much more likely to generate hum;and on-board active electronics have a tendency to  
create hiss.  
-As with the use of any tube amplifier or electronic device, particularly in high gain settings, you may  
be getting outside interference caused by lights,transformers,etc.  
-Be conscious of how the controls of SansAmp GT2 interact.They are atypically sensitive.You need  
not set everything at max to get maximum results.  
3. The Input activates the battery. Don’t forget to unplug or you will waste your battery.The highly effi-  
cient,low power consuming LED will fade as battery runs low (<6.5V).While SansAmp GT2 will contin-  
ue to operate, we recommend replacing the battery at this time.  
4. Buffered bypass ensures no high frequency signal loss through long cable lengths.  
PLACEMENT ORDER OF OTHER EFFECTS  
Place the following effects BEFORE SansAmp GT2:  
Compression,Wah-wah,Envelope Filter  
Place the following effects AFTER SansAmp GT2:  
Chorus,Delay, EQ,Pitch Shifter, Reverb  
®Registered trademarks of their respective companies.  
Names of sample settings are intended for descriptive purposes only and  
should not be construed as an endorsement or affiliation with the companies or artists named.  
 
 
 

Toshiba Portable DVD Player SDP63SWE User Manual
TP Link Modem td w8961nd User Manual
Traulsen Freezer RFF132WUT FHS User Manual
Tricity Bendix Refrigerator TBUR 120 User Manual
Tripp Lite Surge Protector TLM406NC User Manual
Tripp Lite Switch PAM 3 User Manual
Vector Automobile Parts DK080706 User Manual
Viking Refrigerator VC VI DD DFRB536 User Manual
VTech Graphics Tablet 2S User Manual
Vulcan Hart Electric Steamer C24EA3 208 240V BASIC User Manual