VIDEO
CASSETTE
RECORDER
OWNER’S
MANUAL
SF225B
TABLE OF CONTENTS
I IMPORTANT SAFEGUARDS..................................... 2
I PRECAUTIONS ............................................................ 3
I FEATURES ................................................................... 4
I OPERATING CONTROLS AND FUNCTIONS......... 4
I PREPARATION FOR USE .......................................... 6
I INITIAL SET UP FOR USE ........................................ 7
I SET UP FOR USE AGAIN........................................... 8
I PLAYBACK FUNCTION.............................................. 9
I RECORDING FUNCTION ........................................ 10
I TIMER RECORDING................................................. 11
I SPECIAL FEATURES................................................ 12
I TROUBLESHOOTING GUIDE................................. 12
I SPECIFICATIONS ..................................................... 13
I MAINTENANCE......................................................... 13
I INSTRUCCIONES EN ESPAÑOL............................ 14
I WARRANTY ................................................................ 16
SUPPLIED ACCESSORIES
ACCESSORIES
Coaxial Cable
PART NO.
WPZ0102LG006/
WPZ0102TM012
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
Remote Control Unit
Batteries
N9373UD / N9376UD
AA x 2
As an ENERGY
S
TAR®
Partner, our company has
determined that this product meets
If you need additional operating assistance after reading this
the ENERGY S
TAR® guidelines for
S
TAR® is
owner’s manual or to order replacement accessories, please call
energy efficiency. ENERGY
a U.S. registered mark.
TOLL FREE : 1-800-242-7158.
- 1 -
Please read before using this equipment.
EN
PRECAUTIONS
INSTALL LOCATION
For safety and optimum performance of your VCR:
REMOTE CONTROL
We do not recommend the use of universal remote con-
trols. Not all of the functions may be controlled with a
universal remote control.
If you decide to use a universal remote control with this
unit, please be aware that the code number given may
not operate this unit. In this case, please call the manu-
facturer of the universal remote control.
I
Install the VCR in a horizontal and stable position.
Do not place anything directly on top of the VCR. Do
not place the VCR directly on top of the TV.
I
Shield it from direct sunlight and keep it away from
sources of intense heat. Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes
on the sides of the VCR. Avoid locations subject to
strong vibration or strong magnetic fields.
FCC WARNING
This equipment may generate or use radio frequency
energy. Changes or modifications to this equipment may
cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user
could lose the authority to operate this equipment if an
unauthorized change or modification is made.
AVOID THE HAZARDS OF ELECTRICAL
SHOCK AND FIRE
I
Do not handle the power cord with wet hands.
I
Do not pull on the power cord when disconnecting it
from AC wall outlet. Grasp it by the plug.
IMPORTANT COPYRIGHT INFORMATION
I
If, by accident, water is spilled on your VCR, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
Unauthorized recording or use of broadcast television
programming, video tape, film or other copyrighted ma-
terial may violate applicable copyright laws. We as-
sume no responsibility for the unauthorized duplication,
use, or other acts which infringe upon the rights of copy-
right owners.
I
Do not put your fingers or objects into the VCR cas-
sette holder.
MOISTURE CONDENSATION
WARNING
Moisture condensation may occur inside the unit when
it is moved from a cold place to a warm place, or after
heating a cold room or under conditions of high humid-
ity. Do not use the VCR at least for2 hours until itsinside
is dry.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and
can be reused. Please dispose of any materials in accord-
ance with your local recycling regulations.
Batteries should never be thrown away or incinerated
but disposed of in accordance with your local regula-
tions concerning chemical wastes.
VIDEO CASSETTE TAPE
I
This VCR will operate with any cassette that has the
SERIAL NUMBER
mark. For best results, we recommend the use
of high-quality tapes. Do not use poor quality ordam-
aged tapes.
The serial number of this product may be found on the
back of the VCR. No other VCR has the same serial
number as yours. You should record the number and
other vital information here and retain this book as a
permanent record of your purchase to aid identification
in case of theft. Serial numbers are not kept on file.
I
Avoid moisture. Moisture condensation may occur
on the tape if it is moved from a cold place to a warm
place or visa versa. Before using a tape with these
conditions, to avoid damage of the tape and your
VCR, wait until the tape has warmed to room tem-
perature and the moisture has evaporated.
Avoid extreme heat, high humidity and magnetic
fields.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
I
I
Do not tamper with the cassette mechanism.
I
Do not touch the tape with your fingers.
Serial No.
I
You can prevent accidental erasing
of a recording by breaking off the
tab on the back edge of the cassette.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLEC-
TRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE CORRE-
SPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
I
If you decide to record on the tape
Tab
again, cover the hole with plastic
tape.
- 3 -
EN
0J11
FEATURES
Hardware specifications
I Auto Head Cleaner
Playback
I Auto Repeat
I Bilingual on-screen menu display selectable in I 2 Step Picture Search Operation
English or Spanish
I S-VHS Quasi Playback (SQPB)
I 181 channel capability PLL frequency synthesizer
tuner with direct station call
Recording
I 1 Year, 7 events (including Daily and Weekly
Timer Recording)
I OTR (One Touch Recording)
Automatic functions
I Auto power on and off system
I Digital Auto Tracking (DTR)
OPERATING CONTROLS AND FUNCTIONS
VCR FRONT PANEL
1
2
3
4
5
6
REMOTE CONTROL
P
REW
F.FWD
POWER
REC
OTR
PAUSE
STILL
VCR/TV EJECT
E
7
3
8
12
POWER
VCR/TV
1
2
5
8
0
3
6
9
CHANNEL
TAPE
SPEED
CHANNEL
4
7
MENU
15
MENU
+100 AUTO REPEAT
19
18
17
4
14
16
11
7 8
9
10
11 12
13
14
23
DISPLAY SPEED EXIT COUNTER
VCR REAR PANEL
PLARYESET
MEMORY
20
2122
REW
F.FWD
2
3
5
6
STOP
PAUSE/STILL
RECORD
ANT
13
IN
AUDIO
OUT IN
OUT
CH3 CH4
VIDEO
242526 27
1. Cassette Compartment
2. REW button– Press to rewind the tape, or to view
Press to select the setting modes from the on screen
menu.
the picture rapidly in reverse during the playback 5. F.FWD button– Press to rapidly advance the tape, or
mode. (Rewind Search)
s button– Press to cancel a setting of timer program.
Press to correct digits when setting program (For exam-
ple: setting clock or timer program). Press to add or
delete channel numbers during channel preset.
view the picture rapidly in forward during playback.
(Forward Search)
B button– When setting program (For example:
setting clock or timer program), press to determine
your selection and proceed to the next step you want
to input. Press to determine the setting modes from
the on screen menu. Press to add or delete channel
numbers during channel preset.
3. EJECT button– Press to remove the tape from the
VCR.
STOP button– Press to stop the tape motion.
6. PAUSE/STILL button– Press to temporarily stop
the tape during recording or to view a still picture
during playback.
7. POWER button– Press to turn VCR on and off.
Press to activate timer recording, when the timer pro-
gram has been set.
I button– Press to enter digits when setting pro-
gram (For example: setting clock or timer program).
Press to select the setting modes from the on screen
menu.
4. PLAY button– Press to begin playback.
I button– Press to enter digits when setting pro-
gram (For example: setting clock or timer program).
- 4 -
EN
0J11
8. VCR/TV button– Press to select TV or VCR mode.
Each time you press this button, TV screen will
change as shown. The status display (STOP, PLAY
etc.) and the tape speed display (SP, LP (playback
only), or SLP) will disappear after 5 seconds.
VCR position: to view playback, to monitor video
recordings or watch TV using the VCR tuner.
TV position: to watch TV or to view one program
while recording another.
<COUNT mode>
<CLOCK mode>
<OFF mode>
STOP
STOP
5:40PM
CH 02
9. Remote sensor window– Receives the infrared
Press
once
Press
once
signals from the remote control.
SP
0:12:34
SP
10. Indicators
PWR. (power) indicator– Indicates when the VCR
is turned on.
Press once
VCR indicator– Indicates when the VCR is in the
17. COUNTER MEMORY button– Press to set counter
VCR position.
memory on and off. (only on the remote control)
TAPE IN indicator– Indicates when there is a tape
in the VCR.
TIMER indicator– Indicates when the timer record-
ing or OTR has been set.
REC indicator– Indicates during recording. Flashes
when a recording is paused.
CLOCK indicator– Displays current time. PM indi-
cator lits when p.m.
18. COUNTER RESET button– Press to reset counter
to 0:00:00. (only on the remote control)
EXIT button– Press to exit the menu on the TV
screen. (only on the remote control)
19. AUTO REPEAT button– Press to repeat playback
automatically. (only on the remote control)
20. Power cord– Connect to a standard AC outlet
(120V/60Hz).
11. TAPE SPEED button– Press to choose the desired
21. AUDIO OUT jack– Connect to the audio input jack
recording speed : SP/SLP.
of your audio equipment or another VCR.
12. CHANNEL Up or Down buttons– Press to select
22. AUDIO IN jack– Connect to the audio output jack of
the desired channels for viewing or recording.
your audio equipment or another VCR.
Tracking function– Press to minimize video ‘noise’
(lines or dots on screen) during playback (only on the
VCR).
Press to stabilize the picture in the Still mode when
the picture begins to vibrate vertically.
23. ANT. IN terminal– Connect to an antenna, Cable
system or Satellite system.
24. VIDEO OUT jack– Connect to the video input jack
of your video camera or another VCR.
25. VIDEO IN jack– Connect to the video output jack of
13. RECORD button– Press for manual recording.
your video camera or another VCR.
OTR button– Press to activate One Touch Record-
ing. (only on the VCR)
26. CH3/CH4 selector switch– Use to select a video
output channel (3 or 4) for VCR playback.
14. MENU button– Press to display the menu on the TV
27. ANT. OUT terminal– Connects to the antenna input
screen. Press to exit the menu on the TV screen.
terminal on your TV.
15. NUMBER buttons– Press to select desired channels
for viewing or recording. To select channels from 1
to 9, first press "0" button then 1 to 9. (only on the
remote control)
INSTALLING THE BATTERY
+100 button– When selecting cable channels which
are higher than 99, press this button first, then press
the last two digits. (To select channel 125, first press
"+100" button then press "2" and "5"). (only on the
remote control)
Make sure the polarity of battery to install to the remote
control unit.
16. DISPLAY button– Press to display the current time,
channel number, real time tape counter, and other in-
formation on the TV screen. (only on the remote con-
trol)
Install 2 X AA battery
REC (record) indicator
Indicador de grabación (REC)
INDICATORS
PWR. (power) indicator
Indicador de alimentación
TIMER indicato
Indicador del temporizador
TAPE IN indicator
Indicador de videocasete
introducido
PM indicator
Indicador del tarde (PM)
VCR indicator
Indicador de videograbadora
CLOCK indicator / Indicador del reloj
- 5 -
EN
0J11
PREPARATION FOR USE
ANTENNA/CABLE CONNECTIONS
For some of the most common types of connections, please refer to the followings. Use only one connection. For
any further complex connections, please contact your local dealer. (You may need additional accessories which
are not supplied).
1 Disconnect the antenna or cable from your TV.
2
Connect the antenna orcable totheANT.IN(Topjack)
of your VCR.
3 Connect one end of the coaxial cable (supplied) to
4
Connect the other end of the coaxial cable (supplied)
to the UHF/VHF antenna jack of your TV.
the ANT.OUT (Bottom jack) of your VCR.
Basic Connections
[Cable Box or Satellite Box]
OUT
IN
From
Cable or
Satellite
Company
ANT
IN
OR
AUDIO
OUT IN
OUT
Indoor or
Outdoor
Coaxial Cable
(Supplied)
CH3 CH4
VIDEO
Antenna
OR
From
Cable Company
(No Cable Box)
Back of the VCR
IN
IN
L
R
VIDEO
AUDIO
OR
VHF
UHF
VHF
UHF
ANT in
TV A/V Terminal
TV Antenna Terminal
USING OPTIONAL AUDIO/VIDEO
OUTPUT JACKS
If your TV has A/V input jacks, you may connect your
VCR’s AUDIO/VIDEO OUTPUT jacks to the
audio/video input jacks on back of your TV.
Direct audio/video connections usually result in a better
picture and sound quality for tape playback. Please see
your TV’s owner’s manual for A/V input connections.
USING AUDIO/VIDEO INPUT JACKS
You can use A/V input jacks on back panel.
I
When you connect the External source to jacks on
back panel, select "Line-in" position for recording by
pressing the 0, 0 on the remote control or CHANNEL
Up/Down button.
Note to CATV system installer
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected
to the grounding system of the building, as close to the point of cable entry as practical.
- 6 -
EN
0J11
INITIAL SET UP FOR USE
5
Begin channel preset
SETTING THE CH3/CH4
SWITCH
by pressing the B button
once. The tuner scans and
memorizes allactivechannels
in your area.
CH 01
If your TV does not have A/V terminals:
AUTO SET UP
When the VCR is in the Playback mode or when the
VCR is in the VCR position, your TV will receive sig-
nals from the VCR on either channel 3 or 4.
I
The VCR distinguishes be-
tween standard TV channels
and cable channels.
To use the VCR with your TV, set the selector switch to
CH3 or CH4 (which is located
6
After scanning, the tuner stops on the lowest
in the back of your VCR),
memorized channel. The TV screen returns to TV
mode.
whichever is not used for nor-
OUT
CH3
CH4
CH3 CH4
mal broadcasts in your area.
Then set your TV to the same
channel.
I
If "AUTO SET UP" appears on the TV screen again,
check the cable connections. Press the B button once
again and the VCR will begin preset again.
[Back of the VCR]
AUTOMATIC CHANNEL SET UP
You can automatically program the tuner to scan only
the channels you receive in your area.
TO SELECT A DESIRED CHANNEL
You can select the desired channel by using the CHAN-
NELUp or Down button or directly pressing the number
buttons on the remote control.
I
Channel memory programming is NOT needed
Note for using the number buttons:
when you connected the VCR to a cable box or
satellite box as in "Basic connections" on page 6. In
this case, select the VCR and TV to channel 3 or 4
the same channel as the CH3 or CH4 switch on the
back of the VCR. Then, the channel you want to re-
cord or view may be selected at the cable box or sat-
ellite box.
I
When selecting cable channels which are higher than
99, press the +100 button first, then press the last two
digits.
I
You must precede single-digit channel numbers with
a zero (For example: 02, 03, 04 and so on).
I
Follow the steps below once. Repeat it only if there
CLOCK SET UP
Set the clock accurately for proper automatic timer re-
cording. We suggest that you use a TV or radio station
as your time source.
is a power failure orif the VCR is unplugged formore
than 30 seconds. (In these cases, the programmed
channels are erased.)
I
You must follow the steps below before attempting
to play or record a video tape. If you want to play or
record a video tape BEFORE programming the tuner,
you can cancel it by pressing the RESET/EXIT but-
ton. To program the tuner again, see "CHANNEL
SET UP AGAIN" on the next page.
1
Select main menu by pressing the MENU button.
(If the clock is not set, the CLOCK SET menu ap-
pears first. In this case, follow step [3].)
2
Select "CLOCK SET" by pressing the I or I but-
ton. Then, press the B button.
1 You need to connect antenna/cable to the VCR first.
Then, connect the VCR power plug into a standard
AC outlet.
3
Set the clock.
Set the month
Press the IIor I button repeatedly.
Then, press the B button.
2 Turn on the TV and set the TV to channel 3 or 4.
Now set the CH3/CH4 switch on the back of the VCR
to match the channel selected on the TV.
Set the day
Set the year
Press the IIor I button repeatedly.
Then, press the B button.
Press the IIor I button repeatedly.
Then, press the B button.
The day of the week will appear automatically.
3 Turn on the VCR by pressing the POWER button.
Both the PWR. indicator and the VCR indicator on
the VCR come on.
Press the IIor I button repeatedly.
Then, press the B button.
Set the hour
Press the IIor I button repeatedly.
Then, press the B button.
Set the minute
Set the AM or PM
4 Select the On Screen Lan-
LANGUAGE SELECT
————————————————
CLOCK SET
guage ("ENGLISH" or
Press the IIor I button
repeatedly.
B
ENGLISH
[ON]
"ESPAÑOL") by pressing
the I or I button. Then,
press the B button.
MONTH DAY
03 19
YEAR
ESPAÑOL
/
MON 2001
HOUR MINUTE
05 40
AM/PM
PM AM
PM
:
I
To go back one step, press the s button.
Start the clock by pressing the RESET/EXIT or B
4
button after setting the AM or PM.
- 7 -
EN
0J11
SET UP FOR USE AGAIN
TO ADD/DELETE CHANNELS
CHANNEL SET UP AGAIN
When the VCR automatically program the tuner to scan
only the channels you receive in your area, some chan-
nels may be skipped due to weak signal. You can manu-
ally add the channel in the VCR memory. (Of course,
you can later delete the added channel from the memory
again.)
1
Select main menu by press-
- M E N U -
ing the MENU button.
TIMER PROGRAMMING
AUTO REPEAT
[OFF]
B
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
2
Select "CHANNEL SET UP"
by pressing the I or I button.
Then, press the B button.
1 Select main menu by press-
- M E N U -
TIMER PROGRAMMING
3
Select "AUTO SET UP" by
pressing the I or I button.
Then, press the B button. After
scanning, the tuner stops at the
lowest memorized channel.
ing the MENU button.
AUTO REPEAT
[OFF]
CHANNEL SET UP
——————————————————
B
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
B
AUTO SET UP
2 Select "CHANNEL SET UP"
by pressing the I or I button.
Then, press the B button.
MANUAL SET UP
I
The VCR distinguishes between standard TV chan-
nels and cable channels.
3 Select "MANUAL SET UP"
by pressing the I or I button.
Then, press the B button.
CHANNEL SET UP
——————————————————
AUTO SET UP
B
MANUAL SET UP
SELECTING THE ON SCREEN
LANGUAGE
1
Select main menu by press-
- M E N U -
ing the MENU button.
TIMER PROGRAMMING
4 Enter the desired channel
number by pressing the I or
I button.
AUTO REPEAT
[OFF]
CHANNEL SET UP
CLOCK SET
MANUAL SET UP
———————————————
B
LANGUAGE SELECT
2
Select "LANGUAGE SE-
LECT" by pressing the I or
I button. Then, press the B
CHANNEL 30 ( TV )
DELETE
button.
3
Select the On Screen Lan-
guage ("ENGLISH" or
"ESPAÑOL") by pressing
the I or I button.
LANGUAGE SELECT
————————————————
5 Add or Delete it from memory by pressing the B or
s button so that "ADD" or "DELETE" flashes on
the TV screen accordingly.
B
ENGLISH
[ON]
ESPAÑOL
MANUAL SET UP
———————————————
MANUAL SET UP
———————————————
CHANNEL 30 ( TV )
DELETE
CHANNEL 30 ( TV )
ADD
4
Exit the preset mode by pressing the RESET/EXIT
button.
- DELETED -
- MEMORIZED -
6
Exit the preset mode by pressing the RESET/EXIT
button.
- 8 -
EN
0J11
PLAYBACK FUNCTION
NORMAL PLAYBACK
AUTO REPEAT PLAYBACK
Use this feature allows you to play a tape over and over.
1) Select main menu by pressing the MENU button.
1 Insert the prerecorded tape.
The VCR will turn on. If the
safety tab has been removed,
the VCR will start playback
automatically.
2) Select "AUTO REPEAT" by pressing the I or I
button.
3) Begin auto repeat playback by pressing the B button
so that [ON] will appear next to "AUTO REPEAT"
on the TV screen.
2 Turn on the TV and set the TV to channel 3 or 4.
Now set the CH3/CH4 switch on the back of the VCR
to match the channel selected on the TV.
I
If the on-screen menu still remains, press the RE-
SET/EXIT button to exit the menu.
I
You can set AUTO REPEAT to ON or OFF by press-
ing the AUTO REPEAT button on the remote con-
trol.
3 Begin playback by pressing the PLAY button.
I
Tracking adjustment will be set automatically (Digi-
tal Tracking function) when you start playback. To
adjust the tracking manually, press the CHANNEL
Up or Down button on the VCR.
I
To cancel the auto repeat mode, press the B button
at step [3] so that [OFF] appear next to "AUTO RE-
PEAT" on the TV screen.
When you set the auto repeat mode to [ON] while the
counter memory mode is ON, the VCR will exit the
counter memory mode automatically.
I
I
When a tape has reached the end, the VCR will re-
wind the tape to the beginning, eject the tape, and turn
off the VCR automatically.
I
S-VHS Quasi Playback (SQPB)
This unit allows you to view a tape recorded in S-VHS
format. (Noise lines may appear on the picture.)
PICTURE SEARCH
If you jump or repeat the some scene in the playing pro-
gram, press the F.FWD or REW button.
4 To stop playback, press the STOP button.
I
Press it again and the VCR will now search in super
high speed. (in the LP / SLP modes only)
STILL
You can freeze the picture on TV screen by pressing the
PAUSE/STILL button during playback.
I
Usually there will be video "noise" lines (black and
white streaks or dots) on the screen. This is not a
fault of the machine but is a by-product of the
technology involved in producing a 2 Head VCR.
Only a tape recorded in the SLP mode will show a
clear picture. You can change position of the noise
lines on a still picture by pressing the PAUSE/STILL
button repeatedly.
After the VCR has been in Still mode for 5 minutes,
it will stop automatically to protect the tape and the
video head.
I
I
To return playback, press the PLAY button.
- 9 -
EN
0J11
RECORDING FUNCTION
Before recording, make sure:
VIEWING AND RECORDING
THE SAME PROGRAM
I
The desired channel is selected by pressing the num-
ber buttons on the remote control or the CHANNEL
Up/Down button. (If you connected the VCR to a
cable box or satellite box as in "Basic connections"
on page 6, select the VCR to channel 3 or 4 the same
channel as the CH3 or CH4 switch on the back of the
VCR. Then, select the channel you want to record at
the cable box or satellite box. In this case, you can
ONLY record and view the SAME channel. )
1) Begin the recording by pressing the RECORD button.
I
To temporarily stop recording or resume it, press the
PAUSE/STILL button. After the VCR has been in
Pause mode for 5 minutes, it will stop automatically
to protect the tape and the video head.
2) Stop the recording by pressing the STOP button
when recording is completed.
I
I
There is a tape with its safety tab into the VCR.
The desired recording speed is selected in SP(stand-
ard play) or SLP(super long play) mode by pressing
the TAPE SPEED button.
OTR(One Touch Recording)
This function enables you to set the recording length sim-
ply by pressing the REC/OTR button on the VCR.
1) Begin OTR by pressing the REC/OTR button on the
VCR repeatedly until the desired recording length
appears.
Tape Speed
Type of tape T60
SP mode 1 hour
SLP mode 3 hours 6 hours 8 hours
Recording/Playback Time
T120 T160
2 hours 2-2/3 hours
I
Recording stops when 0:00 is reached.
Press
1 press
Display
Recorded Length
(normal recording)
2 presses
3 presses
↓
0:30
1:00
↓
30 minutes
60 minutes
↓
17 presses
8:00
480 minutes
18 presses
(normal recording)
- 10 -
EN
0J11
TIMER RECORDING
You may set the VCR to start and end time for a record-
HINTS FOR TIMER
RECORDING
If there is a power failure or the VCR is unplugged
for more than 30 seconds, the clock setting and all
timer settings will be lost.
If the tape runs out before the end time, the VCR will
switch to the Stop mode immediately, eject the tape
and the VCR power will be turned off. The TIMER
indicator will flash.
If a tape is not in the VCR or does not have the safety
tab, the TIMER indicator flashes and timer recording
cannot be performed. Please insert a recordable tape.
ing while you are away. You can set seven programs to
record on specific days, daily or weekly within a 1 year
period.
I
I
1) Insert a tape with its safety tab into the VCR.
2) Select main menu by pressing the MENU button.
3) Select "TIMER PROGRAMMING" by pressing the
I or I button. Then, press the B button.
I
If you have not yet set the clock, "CLOCK SET" ap-
pears. If so, follow the steps [3] and [4] in "CLOCK
SET UP " section. Then, set the timer recording.
I
4) Set the timer.
TO STOP A STARTED AUTOMATIC
TIMER PROGRAM
Press the STOP/EJECT button on the VCR.
Set the program number (1~7)
PROGRAM NUMBER
4
DATE
START TIME
END
CHANNEL
- - / - -
- - : - - - -
- - : - - - -
- -
Program number which is not set up flashes.
Press the I or I button repeatedly
for the desired program number.
Then, press the B button.
TIME
REC SPEED
- -
Select once, daily or weekly recording
For once: Press the I or I button
to point to "ONCE".
For daily (Monday~Friday):
Press the I or I button
to point to "DAILY".
For weekly: Press the I or I button
to point to "WEEKLY".
TO CHECK, CORRECT, OR CANCEL AN
AUTOMATIC TIMER PROGRAM
1) Turn the power on.
PROGRAM NUMBER
4
ONCE
DAILY
WEEKLY
2) Select main menu by pressing the MENU button.
3) Select "TIMER PROGRAMMING" by pressing the
I or I button. Then, press the B button.
Then, press the B button.
4) Select the program number which you want to
check by pressing the I or I button. The details
of the selected program appears on the TV screen.
Set the date
First, press the I or I button for the month,
then, press the B button.
Next, press the I or I button for the day.
Then, press the B button.
I
Go to the digit you want to change by pressing the
B or s button. Then, enter correct numbers by
Set the start time
First, press the I or I button for the hour,
then, press the B button.
Next, press the I or I button for the minute,
then, press the B button.
pressing the I or I button.
You may cancel the entire program by pressing the
s button during the program number flashes.
I
5) Press the RESET/EXIT button to exit.
6) Press the POWER button to return to timer stand-
by mode.
And then, press the I or I button for AM or PM.
Then, press the B button.
Set the end time
Follow the instructions of "Set the start time"
to set the end time.
Set the channel number
AVOID OVERLAP OF PROGRAMS ...
There is a case that a program will not be performed.
When programs overlap:
Press the I or I button repeatedly
for the desired channel number.
Then, press the B button.
If you connected the VCR to a cable box or satellite box as in
"Basic connections" on page 6, select the VCR to channel 3
or 4 the same channel as the CH3 or CH4 switch on the back
of the VCR. Then, select the channel you want to record at
the cable box or satellite box. Leave the cable box or satellite
I
The program with the earliest start time has priority.
I
Once the earliest program finishes, the overlapping
program with the lower number will begin recording
in sequence.
box on for timer recording.
ONE TIME PROGRAM
I
The illustration below demonstrates the sequence of
recordings.
PROGRAM NUMBER
4
Set the tape speed
Press the I or I button repeatedly
for the desired tape speed.
DATE
START TIME
END
CHANNEL
05/03 THU
07:30 PM
08:30 PM
16
TIME
REC SPEED
SP
Recording Sequence
SP
SLP
Then, press the B button.
Program 1
(10:00AM-11:00AM)
I
To go back one step, press the s button.
5) To set another program, repeat step [4]. To exit, press
the RESET/EXIT button.
6) Press the POWER button to set the timer. The TIMER
indicator on the VCR comes on.
Program 2
(9:00AM-10:00AM)
Program 3
(9:30AM-12:00PM)
9:00AM
10:00AM
11:00AM
12:00PM
*Recording period is SHADED
- 11 -
EN
0J11
SPECIAL FEATURES
COUNTER MEMORY FUNCTION
Use this feature to memorize the beginning of recording
start point.
AUTO REWIND
When a tape has reached the end during recording, play-
back, or fast-forward, the tape will automatically rewind
to the beginning. After rewinding finishes, the VCR will
eject the tape and turn itself to off.
1) Press the COUNTER RE-
REC
SET button on the remote
control to reset the counter.
I
The tape will not auto-rewind during timer recording
or One Touch Recording.
When the Counter Memory is activated, the tape will
rewind to the M0:00:00 and the VCR will go into the
Stop mode.
2) Press the COUNTER
MEMORY button on the
I
SP
M
0:00:00
remote control so that "M"
appears on the TV screen.
3) Record the program.
REAL TIME TAPE COUNTER
This shows the elapsed recording or playback time in
hours, minutes, and seconds. (The displayed time
will not change during blank portions on the tape.)
The "–" indication will appear when the tape is re-
wound further than "0:00:00" on the tape counter.
4) After recording, press the STOP button then the
REW button.
I
I
When "0:00:00" is reached, rewinding operation
goes to stop. And you can view the recording pro-
gram.
I
I
The COUNTER MEMORY button does not function
if the auto repeat mode is set to [ON]. In this case, set
the auto repeat mode to [OFF].
I
To cancel the counter memory mode, press the
COUNTER MEMORY button so that "M" disap-
pears from the TV screen.
TROUBLESHOOTING GUIDE
If you have followed the instructions contained in this manual and have difficulty in operating your VCR, locate
the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to remedy
the problem.
PROBLEM
CORRECTIVE ACTION
Make sure the power plug is connected to an AC outlet.
Make sure the power is turned on.
Make sure the timer recording is set correctly.
Make sure the power is off.
Make sure the VCR clock is set correctly.
Make sure the tape has a safety tab. If needed, cover the hole with
plastic tape.
I
I
I
I
I
I
No power.
Timer recording is not possible.
Cannot go into Record mode.
I
I
Playback picture is partially noisy.
Adjust tracking control for a better picture by pressing the
CHANNEL Up or Down button on the VCR.
Head cleaning may be necessary. Refer to "AUTO HEAD
CLEANING" .
Cannot view a tape but the audio is
OK.
I
I
Make sure the VCR is not in the Menu mode.
Set your TV to the VCR mode and/or press the VCR/TV button so that
the VCR indicator on the VCR comes on.
No picture or poor picture on
playback.
I
I
I
Fine tune your TV.
Re-check the ANT. IN and ANT. OUT connections. See page 6.
Set your TV to the TV mode and/or press the VCR/TV button so that
the VCR indicator on the VCR disappears.
On-the-air TV programs cannot be
seen.
I
I
I
No operation from the infrared
Remote Control.
Make sure the power plug is connected to an AC outlet.
Check batteries in remote control.
You cannot copy a copyrighted video tape. You are experiencing
copy guard protection.
Video or color fades in and out when
making a copy of a video tape.
- 12 -
EN
0J11
SPECIFICATIONS
Television system :
Video heads :
Tape cassette :
Tape speed
Recording :
Playback :
Tuner channel
NTSC, TV standard
Rotary two-head
video cassette
Video output level :
Video output impedance : 75Ω
1Vp-p
Audio output level :
Video input level :
Audio input level :
Power requirement :
Power consumption :
Dimensions :
-6dBv (1KHz)
0.5~2.0Vp-p
-10dBv
120V, 60Hz
12 Watts
SP, SLP
SP, LP, SLP
W
H
14-1/4" (360mm)
3-5/8" (92mm)
VHF :
UHF :
#2~#13
#14~#69
D
8-1/2" (215.5mm)
Cable channel :
RF converter :
Converter output :
Timer indication :
Operating temperature : 5 C~40 C (41 F~104 F)
Terminals
5A, A-5 ~ A-1, A ~ W+84
Built-in VHF converter
VHF Channel 3 or 4.
AM/PM 12-hour system
Weight :
5.1 lbs. (2.3 Kg.) (approx.)
I
Designs and specifications are subject to change
without notice and without legal obligation.
o
o
o
o
I
If there is a discrepancy between languages, the de-
fault language will be English.
Antenna input :
Antenna output :
Video input/output :
F type connector x 1
F type connector x 1
RCA connector x 2
Audio input/output : RCA connector x 2
MAINTENANCE
SERVICING
AUTO HEAD CLEANING
I
Should your VCR become inoperative, do not try to cor-
rect the problem by yourself. There are no user-service-
able parts inside. Turn off, unplug the power plug, and
please call our help line at 1-800-242-7158, to locate an
Authorized Service Center.
Automatically cleans video heads as you insert or re-
move a cassette, so you can see a clear picture.
I
Playback picture may become blurred or interrupted
while the TV program reception is clear. Dirt accu-
mulated on the video heads after long periods of use,
or the usage of rental or worn tapes can cause this
problem.
CABINET CLEANING
If a streaky or snowy picture appears during play-
back, the video heads in your VCR may need to be
cleaned.
I
Wipe the front panel and other exterior surfaces of
the VCR with a soft cloth immersed in lukewarm
water and wrung dry.
1. Please visit your local Audio/Video store and pur-
chase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem,
please call our help line at 1-800-242-7158, to locate
an Authorized Service Center.
I
Never use a solvent or alcohol. Do not spray insecti-
cide liquid near the VCR. Such chemicals may cause
damage and discoloration to the exposed surfaces.
NOTES:
I
Remember to read the instructions included with the
video head cleaner before use.
I
Clean video heads only when problems occur.
- 13 -
EN
0J11
CONEXIONES DE ANTENA/TELEVISIÓN POR CABLE
Para conocer algunos de los tipos de conexión más comunes, consulte 3. Conecte un extremo del cable coaxial (suministrado) a ANT.OUT
las explicaciones siguientes. Utilice solamente una conexión. Para ha-
cer conexiones más complejas, consulte a su concesionario local. (Tal
vez necesite accesorios adicionales que no han sido incluidos.)
(toma inferior) de su videograbadora.
4. Conecte el otro extremo del cable coaxial (suministrado) a la toma
de antena UHF/VHF de su televisor.
NOTA: Para obtener más información, consulte la sección "Conexio- 5. Si su televisor no tiene terminales A/V: Ponga el conmutador se-
nes de antena/televisión por cable" en la página 6.
lector en CH3 o CH4 (en la parte trasera de su videograbadora), el
que no se utilice para las
1. Desconecte la antena o la caja de televisión por cable de su tele-
visor.
2. Conecte la antena o la caja de televisión por cable a ANT.IN (toma
superior) de su videograbadora.
emisiones normales en su
zona. Luego ajuste el televi-
OUT
CH3
CH4
CH3 CH4
sor al mismo canal.
[Parte trasera de la videograbadora]
[Caja de televisión por cable o caja de emisiones de satélite]
Conexiones básicas
OUT
IN
De empresa
de televisión
por cable o
de emisiones
de satélite
ANT
IN
O
O
AUDIO
OUT IN
OUT
Antena
interior o
exterior
Cable coaxial
(suministrado)
CH3 CH4
VIDEO
De empresa
de televisión
por cable
Parte trasera de
la videograbadora
(Ninguna caja
de televisión
por cable)
IN
IN
L
R
AUDIO
VIDEO
O
VHF
UHF
VHF
UHF
ANT in
Terminal TV A/V
Terminal de antena del televisor
PREPARACIÓN DE CANALES
(La antena o la caja de televisión por ca-
ble deberá estar conectada)
NOTA: Cuando utilice su nueva videograbadora por primera vez, o
en el caso de ser necesario después de producirse un fallo en la ali-
mentación, la videograbadora se pondrá inicialmente en el modo de
preajuste cuando se pulse el botón POWER.
Si conecta una caja de televisión por cable o una caja de emisiones vía
satélite, consulte la sección "Preparación automática de canales" del
manual del propietario.
1. Encienda el televisor y ponga el televisor en el canal 3 ó 4. Ahora
ponga el conmutador de la parte trasera de la videograbadora para
que concuerde con el canal seleccionado en el televisor.
PREPARACIÓN DEL RELOJ
1. Pulse el botón MENU hasta que aparezca el menú principal.
(Si el reloj no está puesto en hora y se pulsa el botón MENU, el
menú AJUSTE DE RELOJ aparece en primer lugar. En este caso,
siga el paso 3.)
2. Pulseelbotón LoLpara indicara"AJUSTE DERELOJ". Luego,
pulse el botón B.
3.
Ajuste el mes.
Ajuste el día.
Ajuste el año.
Ajuste la ora.
Ajuste el minuto.
Pulse repetidamente el botón LLo L .
Luego, pulse el botón B .
Pulse repetidamente el botón LLo L .
Luego, pulse el botón B .
Pulse repetidamente el botón LLo L .
Luego, pulse el botón B .
2. Pulse el botón POWER para encender la video-
SELEC. IDIOMA
Pulse repetidamente el botón LLo L .
Luego, pulse el botón B .
grabadora.
———————————————
ENGLISH
3. Seleccione "ENGLISH" o "ESPAÑOL" (Spa-
nish) pulsando el botón L o L. Y luego pulse
el botón B.
B ESPAÑOL [ON]
Pulse repetidamente el botón LLo L .
Luego, pulse el botón B .
AJUSTE DE RELOJ
4. Pulse una vez el botón B.
Pulse repetidamente
el botón LLo L .
Ajuste la
mañana (AM) o
la tarde (PM).
MES
0 3
DIA
1 9
AÑO
LUN 2001
El sintonizador explora y memoriza todos los canales activos de
su zona. Tras la exploración, el sintonizador se detiene en el canal
memorizado más bajo.
/
HORA MINUTO
05 40
AM/PM
PM AM
PM
:
L
Para volver atrás un paso, pulse el botón s.
4. Después de establecer AM o PM, pulse el botón RESET/EXIT o
B para poner en funcionamiento el reloj.
- 14 -
ES
0J01
CONTROLES DE FUNCIONAMIENTO Y FUNCIONES
1
2
3
4
5
6
PANEL DELANTERO
MANDO A DISTANCIA
P
DE LA VIDEOGRABADORA
REW
F.FWD
REC
OTR
PAUSE
STILL
POWER
VCR/TV EJECT
3
E
7
3
8
POWER
CHANNEL
1
2
5
8
0
VCR/TV
TAPE
SPEED
MENU
CHANNEL
6
4
7
12
15
9
MENU
+100 AUTO REPEAT
7
8
9
10
11 12
13
14
23
19
18
17
4
14
16
11
PANEL TRASERO DE LA
VIDEOGRABADORA
DISPLAY SPEED EXIT COUNTER
20
2122
MEMORY
PLARYESET
REW
F.FWD
2
3
5
6
ANT
IN
AUDIO
STOP
PAUSE/STILL
RECORD
13
OUT IN
OUT
CH3 CH4
VIDEO
242526 27
1. Compartimiento del videocasete
12. Botones de selección de canales (CHANNEL) - Púlselos para se-
leccionar los canales deseados para ver o grabar.
2. Botón de rebobinado (REW) - Púlselo para rebobinar la cinta o para
ver rápidamente la imagen en retroceso durante el modo de reproducción.
(Búsqueda con rebobinado)
Función de seguimiento – Pulse los botones para minimizar el "ruido"
de vídeo (líneas o puntos en la pantalla) durante la reproducción (sólo en la
videograbadora).
Púlselo para estabilizar la imagen en el modo de imagen fija cuando ésta
empieza a vibrar verticalmente.
Botón s - Púlselo para cancelar un ajuste de programa de temporizador.
Púlselo para corregir los dígitos al programar (por ejemplo: puesta en hora
del reloj o un programa de temporizador). Púlselo para añadir o borrar nú-
meros de canales durante el preajuste de canales.
3. Botón de expulsión (EJECT) - Púlselo para sacar el videocasete de la
videograbadora.
13. Botón de grabación (RECORD) - Púlselo para realizar la grabación
manual.
Botón de grabación con un toque (OTR) - Púlselo para activar la
grabación con un toque. (Sólo en la videograbadora)
Botón de parada (STOP) - Púlselo para detener la cinta.
14. Botón de menús (MENU) - Púlselo para visualizar los menús en la pan-
talla del televisor. Y vuelva a pulsarlo para salir de los menús de la pantalla
del televisor.
15. Botones de números (NUMBER) - Púlselos para seleccionar los cana-
les deseados para ver o grabar. Para seleccionar los canales del 1 al 9, pulse
primero el botón "0" y luego el botón 1 a 9. (Sólo en el mando a distancia)
Botón L - Púlselo para introducir los dígitos cuando establezca programas
(por ejemplo: puesta en hora del reloj o un programa de temporizador).
Púlselo para seleccionar los modos de ajuste en el menú en pantalla.
4. Botón de reproducción (PLAY) - Púlselo para iniciar la reproducción.
Botón L - Púlselo para introducir los dígitos cuando establezca programas
(por ejemplo: puesta en hora del reloj o un programa de temporizador).
Púlselo para seleccionar los modos de ajuste en el menú en pantalla.
5. Botón de avance rápido (F.FWD) - Púlselo para avanzar rápidamente
la cinta o para ver rápidamente la imagen en avance durante la reproducción.
(Búsqueda en avance)
Botón +100 - Cuando seleccione canales de televisión por cable cuyo nú-
mero sea superior al 99, pulse primero este botón, y luego pulse los dos
últimos dígitos. (Para seleccionar el canal 125, pulse primero el botón
"+100" y luego el "2" y el "5".) (Sólo en el mando a distancia)
16. Botón del visualizador (DISPLAY) - Púlselo para visualizar en la pan-
talla del televisor la hora actual, el número del canal, el contador de cinta en
tiempo real y otra información. (Sólo en el mando a distancia)
Botón B - Cuando establezca un programa (por ejemplo: puesta en hora
del reloj o un programa de temporizador), púlselo para determinar su selec-
ción y proseguir con el siguiente paso que desee introducir. Púlselo para
determinar los modos de ajuste del menú en pantalla. Púlselo para añadir o
borrar números de canales durante el preajuste de canales.
6. Botón de pausa/imagen fija (PAUSE/STILL) - Púlselo para detener
temporalmente la cinta durante la grabación o para ver una imagen fija du-
rante la reproducción.
7. Botón de la alimentación (POWER) - Púlselo para encender y apagar
la videograbadora. Púlselo para activar la grabación con temporizador cuan-
do ésta haya sido establecida.
8. Botón de videograbadora/televisor (VCR/TV) - Púlselo para selec-
cionar el modo de la videograbadora (VCR) o del televisor (TV).
PosiciónVCR:para ver la reproducción, comprobarlasgrabacionesdevídeo
o ver programas de TV utilizando el sintonizador de la videograbadora.
Posición TV: para ver programas de TV o para ver un programa mientras se
graba otro.
Cada vez que pulse este botón, la pantalla del televisor cambiará. La visua-
lización del estado (PARAR, REPRODUCIR, etc.) y la visualización de
velocidad de la cinta [SP, LP (reproducción solamente) o SLP] desaparecerá
después de 5 segundos.
17. Botón de memoria del contador (COUNTER MEMORY) - P ú l s e l o
para activar y desactivar lamemoriadelcontador. (Sólo en el mando adistancia)
18. Botón de reposición del contador (COUNTER RESET) - Púlselo
para reponer el contador a 0:00:00. (Sólo en el mando a distancia)
Botón de salida (EXIT) - Púlselo para salir de los menús en pantalla.
(Sólo en el mando a distancia)
19. Botón de repetición automática (AUTO REPEAT) - Púlselo para
repetir automáticamente la reproducción. (Sólo en el mando a distancia)
20. Cable de alimentación - Conéctelo a una toma de CA estándar (120
V/60 Hz).
21. Toma de salida de audio (AUDIO OUT) - Conéctela a la toma de en-
trada de audio de su equipo de audio o de otra videograbadora.
22. Toma de entrada de audio (AUDIO IN) - Conéctela a la toma de sali-
da de audio de su equipo de audio o de otra videograbadora.
23. Terminal de entrada de antena (ANT. IN) - Aquí se conecta una ante-
na, sistema de televisión por cable o sistema de emisiones vía satélite.
24. Toma de salida de vídeo (VIDEO OUT) - Conéctela a la toma de en-
trada de vídeo de su videocámara o de otra videograbadora.
25. Toma de entrada de vídeo (VIDEO IN) - Conéctela a la toma de salida
de vídeo de su videocámara o de otra videograbadora.
26. Conmutador selector de canales CH3/CH4 - Se utiliza para seleccio-
naruncanaldesalidadevídeo(3 ó4)paralareproduccióndelavideograbadora.
27. Terminal de salida de antena (ANT. OUT) - Conéctelo al terminal de
entrada de la antena de su televisor.
9. Ventanilla sensora del mando a distancia - Recibe las señales in-
frarrojas procedentes del mando a distancia.
10. Indicadores [Consulte las ilustraciones de las página 5.]
Indicador de alimentación (PWR.) - Indica que la alimentación está
conectada.
Indicador de videograbadora/televisor (VCR) - Indica que la video-
grabadora está activada.
Indicador de videocasete introducido (TAPE IN) - Indica que hay
un videocasete en la videograbadora.
Indicador del temporizador (TIMER) - Indica que ha sido establecida
la grabación con temporizador u OTR.
Indicador de grabación (REC) - Indica que la videograbadora está gra-
bando. Parpadea cuando la grabación ha hecho una pausa.
Indicador del reloj y tarde(PM) - Indica la hora actual cuando el reloj
está ajustado. Indica PM a la tarde.
11. Botón de velocidad de cinta (TAPE SPEED) - Púlselo para elegir la
velocidad de grabación deseada: SP/SLP.
- 15 -
ES
0J01
FUNAI CORPORATION
LIMITED WARRANTY
Funai Corporation will exchange or repair this product, at its option, in the event of defect in materials or workmanship as follows:
EXCHANGE DURATION:
1-90 DAYS:
FUNAI CORPORATION will exchange for a new unit without charge for a period of ninety (90) days
from the date of original retail purchase.
91-365 DAYS: FUNAI CORPORATION will exchange for a factory-service-to-new-condition unit for a charge of
$49.00 for the period of ninety one (91) days to three hundred sixty five (365) days from the date of
original retail purchase.
REPAIR DURATION:
LABOR:
FUNAI CORPORATION will provide the labor without charge for a period of ninety (90) days from
the date of original retail purchase.
PARTS:
FUNAI CORPORATION will provide parts to replace defective parts without charge for a period of
one (1) year from the date of original retail purchase. Two (2) years for Picture Tube. Certain parts
are excluded from this warranty.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be required together with
the product to obtain exchange or service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced or missing. This FUNAI CORPORATION
Limited warranty applies only to product purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship, which occur during normal use. It does not cover damage which occurs in
shipment, or failures which are caused by repairs, alterations, or parts not supplied by FUNAI CORPORATION, or damage which results from accident,
misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of
this product, or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL UNITS), ANY
COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMONSTRATION OR FLOOR MODELS.
FUNAI CORPORATION AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT
OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS PRODUCT.
THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANT ABILITY, AND
FITNESS FOR A PARTICULAR PURPOSE, THAT ARE HEREBY DISCLAIMED BY FUNAI CORPORATION AND ITS REPRESENTATIVES
OR AGENTS IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED CENTER. THIS WARRANTY IS
VALID WHEN THE PRODUCT IS DELIVERED PREPAID TO A FUNAI AUTHORIZED SERVICE FACILITY.
PRIOR TO RETURNING THIS PRODUCT TO THE FACTORY SERVICE CENTER FOR REPAIR, CONTACT THE FUNAI SERVICE DEPART-
MENT TO RECEIVE A RETURN FOR REPAIR AUTHORIZATION. ANY POSTAGE, INSURANCE, AND SHIPPING COSTS INCURRED IN
PRESENTING PRODUCT FOR REPAIR ARE THE SHIPPER’S RESPONSIBILITIES.
CAREFULLY PACK WITH PROPER PACKING MATERIALS, PREFERABLY IN THE ORIGINAL CARTON OR PACKING MATERIALS AND
CARTON OBTAINED FROM FUNAI CORPORATION.
ENCLOSE WRITTEN DOCUMENTATION DETAILING THE COMPLAINT. PLACE INSIDE THE CARTON OR IN A PACKING SLIP
ENVELOPE ON THE OUTSIDE OF THE CARTON.
A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT MUST ACCOMPANY THE PRODUCT. IF NO PROOF OF PURCHASE IS
INCLUDED, THE WARRANTY WILL NOT BE HONORED.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO
STATE, IF AT ANY TIME DURING THE WARRANTY PERIOD YOU ARE UNABLE TO OBTAIN SATISFACTION WITH THE EXCHANGE
OR REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORPORATION.
ATTENTION:
FUNAI CORPORATION RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR NOTICE.
For information about your product, or for information on how to exchange or repair your product, telephone or write to the following:
FUNAI CORPORATION
Customer Service
100 North Street; Teterboro, NJ 07608
Telephone (800)242-7158
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in China
0VMN0????
H7740UD ★★★★★
|