Sunbeam Bedding Thermostat HE3100 User Manual

Convection Plus Heaters  
Instruction Booklet  
HE3100 1200W heater with micathermic elements  
HE3900 2200W heater with micathermic elements  
Please read these instructions carefully  
and retain for future reference.  
 
Sunbeam’s Safety Precautions  
Sunbeam are very safety conscious when  
• Never leave an appliance unattended while  
in use.  
designing and manufacturing consumer products,  
but it is essential that the product user also  
exercise care when using an electrical appliance.  
Listed below are precautions which are essential  
for the safe use of an electrical appliance:  
• Do not use an appliance for any purpose  
other than its intended use.  
• Do not place an appliance on or near a hot gas  
flame, electric element or on a heated oven.  
Do not place on top of any other appliance.  
• Read carefully and save all the instructions  
provided with an appliance.  
• Do not let the power cord of an appliance hang  
over the edge of a table or bench top or touch  
any hot surface.  
• Always turn the power off at the power outlet  
before you insert or remove a plug. Remove  
by grasping the plug – do not pull on the cord.  
• For safety reasons and to avoid maintenance  
by unskilled persons, some appliances are  
‘sealed’ using tamperproof screws. Such  
appliances should always be returned to the  
nearest Sunbeam Appointed Service Centre  
for adjustment or repair if required.  
Turn the power off and remove the plug  
when the appliance is not in use and  
before cleaning.  
• Do not use your appliance with an extension  
cord unless this cord has been checked  
and tested by a qualified technician or  
service person.  
• Do not operate any electrical appliance with  
a damaged cord or after the appliance has  
been damaged in any manner. If damage is  
suspected, return the appliance to the nearest  
Sunbeam Appointed Service Centre  
• Always use your appliance from a power  
outlet of the voltage (A.C. only) marked  
on the appliance.  
for examination, repair or adjustment.  
• This appliance is not intended for use by young  
children or infirm persons unless they have  
been adequately supervised by a responsible  
adult to ensure that they can use the appliance  
safely.  
• For additional protection, Sunbeam  
recommend the use of a residual current  
device (RCD) with a tripping current not  
exceeding 30mA in the electrical circuit  
supplying power to your appliances.  
• Young children should be supervised to ensure  
that they do not play with the appliance.  
• Do not immerse the appliance in water  
or any other liquid unless recommended.  
If you have any concerns regarding the performance and use of your appliance,  
Ensure the above safety precautions are understood.  
1
 
 
Sunbeam’s Safety Precautions  
• This heater becomes hot during use. To avoid  
burns, do not let bare skin touch hot surfaces.  
If provided, use handles when moving this  
heater. Keep combustible materials such as  
furniture, pillows, bedding, papers, clothes and  
curtains at least 3 feet (90cm) away from the  
front of the heater and keep them away from  
the sides and rear.  
• Do not insert or allow foreign objects to enter  
any ventilation or exhaust openings as this may  
cause electric shock or fire, or damage to the  
heater.  
To prevent a possible fire, do not block air  
intakes or exhaust in any manner. Do not use  
on soft surfaces, such as beds, where opening  
may become blocked.  
• Extreme caution is necessary when any heater  
is used by or near children or invalids and  
whenever the heater is left unattended.  
• A heater has hot and arcing or sparking parts  
inside. Do not use it in areas where petrol,  
paint or flammable liquids are used or stored.  
• Always unplug the heater when not in use.  
• Do not use outdoors.  
To prevent overheating, do not cover the  
heater.  
• Do not run the cord of the heater under  
carpeting. Do not cover the cord with throw  
rugs, runners or other floor coverings. Arrange  
the cord away from traffic areas where it will  
not be tripped over.  
• When turned on for the first time, your  
new heater will emit a slight odour for  
up to 8 hours. This is due to the initial  
heating of the materials used. It is safe, not  
detrimental to the performance of the heater  
and will not reoccur. Sunbeam advises that  
the heater be placed in a well ventilated  
area during this period.  
• Do not locate the heater immediately below a  
socket outlet.  
• Do not use this heater in the immediate  
surrounds of a bath, shower, laundry area or  
swimming pool.  
If you have any concerns regarding the performance and use of your appliance,  
Ensure the above safety precautions are understood.  
2
 
Sunbeam’s Total Safety System  
Safety auto shut-off  
Instant tip-over cut-out  
Your Sunbeam Convection Plus Heater is  
equipped with a safety system that detects  
any abnormally high temperatures within the  
heater and automatically cuts power to the  
heating element, preventing overheating.  
Once the heater has cooled it will  
Your Sunbeam Convection Plus Heater is also  
equipped with an instant tip over cut-out  
switch. This switch automatically interrupts  
the power flow to the heating element when  
the heater is tilted to a certain angle. If  
the heater is tipped over, it will not turn on  
until it has been placed back in the upright  
position.  
automatically resume normal operation.  
Thermal back-up fuse  
Note: The tip over cut-out switch will activate  
when the heater is tilted forward, backward  
or sideways. Care should be taken to ensure  
your heater remains upright at all times.  
In addition to this automatic shut-off, your  
heater contains a thermal back-up fuse to  
provide additional back-up protection. If the  
heater is in an overheat situation, the back-  
up fuse will open, stopping the power flow  
to the heating element. This fuse cannot  
be reset, so in the event that the back-up  
fuse is activated, the heater will need to be  
replaced.  
3
 
 
Features of your HE3100  
Convection Plus Heater  
Double heat micathermic elements  
The revolutionary micathermic heating  
elements produce both radiant and  
convection heat. Instant heat radiates from  
the large surface area in one minute, while  
natural convection circulates warm air around  
the room quickly and evenly.  
Wall mountable  
The slim design is ideal for wall mounting.  
The unique reflective design keeps the rear of  
the heater cooler, enabling it to be mounted  
directly onto the wall, without the clearance  
required by other panel heaters.  
Safety auto shut-off  
This built-in safety system detects any  
abnormally high temperatures within the  
heater and automatically switches it off to  
prevent overheating.  
Handle and wheels  
Wheels and a handle at the rear of  
the unit allow you to safely move the  
heater while in use.  
Instant tip over cut-out  
The instant tip over cut-out switch  
Figure 1  
automatically cuts the power flow to the  
heating element if the heater is tipped over.  
The heater will not resume operation until it  
is replaced in the upright position.  
4
 
 
Power ON light  
Illuminates to indicate that the  
heater is switched on.  
Mode dial  
Turn the mode dial to select your  
desired setting: OFF, LOW (1)  
or HIGH (2).  
Thermostat indicator light  
The red thermostat light indicates  
that the heater is warming up to the  
selected temperature and will go out  
when the selected temperature has  
been reached.  
Thermostat dial  
Turn the thermostat dial clockwise to  
select your desired temperature.  
Adjustable thermostat  
The adjustable thermostat allows you  
to set the temperature to your desired  
comfort level.  
Once the selected heat level is  
reached, the heater will automatically  
cycle on and off to maintain it.  
Dimensions  
When the wheels are attached, your  
HE3100 Convection Plus heater is  
approximately:  
(L)620 x (W)245 x (H)510mm  
5
 
Features of your HE3900  
Convection Plus Heater  
Double heat micathermic elements  
The revolutionary micathermic heating  
elements produce both radiant and  
convection heat. Instant heat radiates from  
the large surface area in one minute, while  
natural convection circulates warm air around  
the room quickly and evenly.  
Safety auto shut-off  
This built-in safety system detects any  
abnormally high temperatures within the  
heater and automatically switches it off to  
prevent overheating.  
Instant tip over cut-out  
The instant tip over cut-out switch  
automatically cuts the power flow to the  
heating element if the heater is tipped over.  
The heater will not resume operation until it  
is replaced in the upright position.  
Handle and wheels  
Wheels and a handle at the rear of  
the unit allow you to safely move the  
heater while in use.  
Wall mountable  
The slim design is ideal for wall mounting.  
The unique reflective design keeps the rear of  
the heater cooler, enabling it to be mounted  
directly onto the wall, without the clearance  
Figure 2  
required by other panel heaters.  
Adjustable thermostat  
The adjustable thermostat allows you to set  
the temperature to your desired comfort level.  
Once the selected heat level is reached, the  
heater will automatically cycle on and off to  
maintain it.  
6
 
 
Remote control  
The easy to use remote control enables the  
heater to be operated from anywhere in the  
room.  
Figure 3  
LED screen  
The LED screen displays the current settings  
including the ambient room temperature, the  
selected mode, or timer setting.  
HI  
C
ON/OFF switch  
Illuminates to indicate that the heater is  
switched on.  
Mode button  
Press the mode button to select your desired  
operating mode: STANDBY, LO, HI or AUTO.  
Select the AUTO mode when setting the  
digital thermostat.  
Timer button  
The timer button allows you to program the  
heater to automatically switch on or off after  
a desired time period. It can be set to turn  
on between 1 and 12 hours or off between  
0.5 and 8 hours.  
Infrared receiver  
Point the remote control towards the infrared  
receiver to operate the heater from anywhere  
in the room.  
Plus/minus arrows  
Use the plus/minus arrow buttons when  
in AUTO mode to select your desired heat  
setting or after pressing the timer button to  
select your desired time setting.  
Dimensions  
When the wheels are attached your  
HE3900 Convection Plus heater is  
approximately:  
(L)850 x (W)245 x (H)600mm  
7
 
Using your Convection Plus Heater  
HE3100 – 1200W heater with micathermic elements  
1.Place the heater on a flat level surface and  
ensure that the air intake and outlet are  
clear of obstructions.  
5.Turn the thermostat dial clockwise until  
the red thermostat indicator light turns on,  
indicating that the heater is warming to  
the selected temperature. This light will go  
out when the selected temperature level is  
reached.  
Note: When turned on for the first time,  
your new heater will emit a slight odour  
for up to 8 hours. This is due to the initial  
heating of the materials used. It is safe,  
not detrimental to the performance of  
the heater and will not reoccur. Sunbeam  
advises that the heater be placed in a well  
ventilated area during this period.  
6.The thermostat is now set and will  
automatically maintain the pre-set  
temperature level by turning the heater on  
and off.  
7.To adjust the selected temperature level,  
rotate the thermostat dial anti-clockwise to  
lower or clockwise to raise the temperature.  
2.Ensure that the mode dial and thermostat  
dial are both in the OFF position.  
3.Insert the plug into a 230/240V power  
outlet and turn the power on. The power  
ON light will illuminate.  
8.To turn the heater off, move the mode dial  
to the OFF position.  
4.Move the mode dial to your desired heat  
setting, either low heat (1) or high heat  
(2).  
8
 
 
Using your Convection Plus Heater continued  
HE3900 – 2200W heater with micathermic elements and remote control  
1.Place the heater on a flat level surface and  
ensure that the air intake and outlet are  
clear of obstructions.  
Using the remote control  
The remote control allows you to conveniently  
operate the heater from anywhere in the room.  
(Refer to Note on Page 8).  
The buttons on the remote control are  
identical to the buttons on the heater. When  
using your remote control simply follow the  
normal operation instructions outlined on  
pages 9 and 10 in addition to the points  
below.  
2.Ensure that the ON/OFF switch is in the  
OFF position.  
3.Insert the plug into a 230/240V power  
outlet and turn the power on. Move the  
ON/OFF switch (located on the side of the  
heater) to the ON position. The ON/OFF  
switch will then illuminate.  
1.Ensure that the remote control contains  
2 x AAA batteries.  
The LCD screen will display the ambient  
room temperature.  
2.Point the remote towards the infrared  
receiver on the heater (located below the  
plus/minus arrows). Ensure that there are  
no objects blocking the path between the  
remote and the infrared receiver.  
Note: When the heater is switched on it will  
be automatically set to the standby mode.  
4.Press the mode button to select your  
desired operating mode. Each time you  
press the mode button, it will scroll  
through the various settings as follows:  
3.Follow steps 1 to 4 on the left column of  
this page.  
Note: The maximum transmission distance  
between the heater and remote is  
approximately 30 metres.  
the heater remains inactive  
STANDBY  
when in this mode  
Setting the digital thermostat  
The digital thermostat allows you to set your  
desired temperature for the room. The heater  
will then cycle on and off to maintain it.  
the heater will continuously run  
at approximately 800 watts  
LO  
1. Follow steps 1 to 3 on the left column of  
this page.  
the heater will continuously run  
at approximately 2200 watts  
HI  
2.Press the mode button until the AUTO  
mode is displayed. Once in AUTO mode,  
the LED screen will flash your previous  
pre-set temperature for 5 seconds. After  
5 seconds the LED screen will display the  
ambient room temperature.  
for operating the digital  
thermostat  
AUTO  
5.To turn the heater off, move the ON/OFF  
switch to the OFF position.  
9
 
Using your Convection Plus Heater continued  
3.Use the plus/minus arrows to select your  
desired setting. The LED screen will  
flash the set value for 5 seconds. After 5  
seconds the LED screen will display the  
ambient room temperature.  
4.Once you have selected your desired timer  
setting, the ambient room temperature and  
the timer icon  
screen.  
will display on the LED  
Note: When the time has run out, the  
timer icon will cease to appear on the  
LED screen. The heater will then return to  
STANDBY mode.  
Note: The temperature range is from 15ºC  
to 28ºC. If you scroll past 28ºC the display  
will automatically return to 15ºC.  
4.The digital thermostat is now set and  
will automatically maintain your selected  
temperature level by turning the heater on  
and off.  
Timer auto ON function  
The timer auto on function allows you  
to program the heater to switch on at a  
specified time to preheat the room.  
Note: It is normal for the heater to cycle  
on and off as it maintains the selected  
temperature.  
1.Set the heater to the standby mode, by  
pressing the mode button.  
Note: The LED screen will appear black in  
this mode.  
5.To turn the heater off, move the ON/OFF  
switch to the OFF position.  
2.Press the timer button. The LED screen  
will display a default time of 0.0hr.  
Using the timer  
Your HE3900 Convection Plus heater features  
a timer function that switches the heater off  
after a specified period of time, eg: 3 hours.  
It also enables you to preheat the room by  
switching the heater on automatically.  
3.Use the plus/minus arrows to select the  
number of hours you wish the heater to  
operate before it automatically switches on,  
between 1 and 12 hours.  
Note: The timer will automatically set  
within 5 seconds of the last time that  
either the plus/minus arrows or timer  
buttons are pressed.  
Timer auto OFF function  
1.Set the heater to the desired setting using  
the mode button.  
2.Press the timer button. The LED screen  
will display a default time of 0.0hr.  
4.Once you have selected your desired timer  
setting, the ambient room temperature and  
the timer icon  
screen.  
will display on the LED  
3.Use the plus/minus arrows to select the  
number of hours you wish the heater to  
operate before it automatically switches  
off, between 0.5 and 8 hours.  
Note: When the time has run out, the  
timer icon will cease to appear on the  
LED screen. The heater will then return  
to AUTO mode, set to your last pre-set  
temperature.  
Note: The timer will automatically set  
within 5 seconds of the last time that  
either the plus/minus arrows or timer  
button are pressed.  
10  
 
Wall Mounting and Attaching  
the Wheels  
Wall mounting  
1.Before wall mounting your heater, remove  
the wheels.  
2.Mark the screw location on the wall,  
approximately 1 metre from the floor.  
Note: The heater must be fixed no lower  
than 6.5cm above the floor and no higher  
 
�  
than 1.8 metres above the floor. The heater  
must also be fixed at least 1 metre from  
both the corner and ceiling (refer to figure  
4 below).  
Figure 5  
3.Insert one of the screw anchors into  
the hole.  
Drill the first hole using a suitable drill bit.  
4.Put the mounting support on the wall over  
the hole and screw it into place.  
 
�  
5.Mark the second screw location,  
approximately 138mm from the first hole,  
and 1 metre from the floor. Drill the second  
hole.  
�  
�  
6.Insert the second screw anchor into the  
hole.  
Figure 4  
7.Place the mounting support over the second  
hole and screw it into place. Tighten both  
screws.  
Note: Any electrical appliances to be fitted  
in a bathroom should be installed by a  
qualified electrician in accordance with  
Australian/New Zealand Standard Wiring  
Rules. Portable heaters should not be used  
in a bathroom.  
8.Lift the heater and position over the screws.  
Attaching the wheels  
Fix each wheel support in position with the  
screws provided.  
Heaters that can be permanently fixed  
must be installed so that any controls  
cannot be reached by a person using a  
bath or shower, as shown in Figure 5.  
11  
 
 
Care and Cleaning  
Ensure that the heater is switched off and  
disconnected from the power outlet before  
cleaning.  
Do not use harsh or abrasive cleaners to  
clean your heater, as these will damage the  
surface.  
Carefully wipe the exterior of the heater  
with a soft damp cloth and dry thoroughly  
with a dry cloth.  
If not wall mounted, store the heater in a  
cool dry place when not in use.  
Over time, dust may accumulate on the  
front grille. This can be removed by wiping  
with a damp cloth, or by carefully going  
across the grille with a vacuum cleaner or  
hand held vacuum.  
12  
 
 
‘Sunbeam’, is a registered trademark of Sunbeam  
Corporation.  
Made in China. Due to minor changes in design or  
otherwise, the product may differ from the one shown  
in this leaflet. Backed by Sunbeam’s 3 Year Replacement  
Guarantee and National Service Network.  
© Copyright. SUNBEAM CORPORATION LIMITED 2006.  
ABN 45 000 006 771  
Sunbeam Corporation is a division of GUD Holdings Ltd.  
For more information or advice on this or any other  
Sunbeam appliance, visit www.sunbeam.com.au or  
contact the Sunbeam Consumer Service Line.  
Australia 1800 025 059  
New Zealand 0800 786 232  
01/06  
 
Consumer Hotline  
Australia  
1800 025 059  
New Zealand  
0800 786 232  
is a registered Trademark of Sunbeam  
Corporation Limited. ABN 45 000 006 771.  
© Sunbeam Corporation Limited 2006.  
 

Shindaiwa Blower 68232 94011 User Manual
Sony Car Stereo System CDC X317 User Manual
Sony Digital Camera CSS TNA User Manual
Sony Headphones WRT 807A User Manual
Sony Video Game Headset SBH70 User Manual
Stanton DJ Equipment VRM 10 User Manual
Star Manufacturing Fryer 510FD User Manual
Star Manufacturing Waffle Iron SWB7R1E User Manual
Star Micronics Printer NX 2420 User Manual
State Industries Water Heater STGPG 0303 User Manual