Stanton DJ Equipment PRO 30 User Manual

PRO-30  
PROFESSIONAL STEREO PREAMP MIXER  
OWNERS MANUAL  
PRO-30  
Register this product online  
@
@
STANTON MAGNETICS, LLC  
© 1999, Stanton Magnetics, LLC  
 
DESCRIPTION OF FUNCTIONS  
7. Meter mode selector: Determines the setting of the level meter (6). When pressed,  
cue levels of channels 1 and 2 are displayed. When released, stereo master output  
signal is displayed.  
8. Power switch: Selects power "ON" or "OFF"  
9. Fader Start controls: Activate the Fader Start function when connected to a CD player  
with fader start capabilities (such as the Next! NCD-7000). When fader start is  
engaged, the CD player can be started and paused by the crossfader. This function is  
defeated while crossfader is reversed.  
10. Master level control: Controls the overall signal output level of the Master output  
11. Booth level control: Controls the overall signal output level of the Booth output  
12. Cue level control: Controls the overall headphone output level.  
13. Cue select: 3 position selector switch dtermines what is heard in the headphones,  
channel 1, 2, or master output  
14. Headphone output: Connection for 1/4 inch headphone.  
headphone impedance is 32-200 ohms for maximum volume  
Recommended  
15. Mic EQ: Individual controls for low and high frequencies equalization with (+/-12 dB)  
Any changes made to EQ settings will change the overall microphone output  
level.  
16. Mic volume control: Controls the overall mirophone output level  
17. Crossfader Reverse: Reverses the direction of the crossfader. The fader start function  
is defeated while crossfader is reversed.  
18. Microphone input: 1/4” connector  
19. Ground connector: Connects to the turntable ground connector to eliminate electrical  
hum. Ground connectors are usually supplied with turntables  
20. Phono/CD inputs: Switchable line / phono signal inputs for channels 1 and 2  
21. Line inputs: Line signal inputs for channels 1 and 2  
22. Phono/CD selector switches: Switches CD/Phono inputs for channels 1 and 2 between  
line and phono  
23. Fader Start output: Connects to the fader start inputs of CD players with fader start  
function such as the Next! NCD-7000  
24. Booth output: Auxiliary output, usually for DJ booth monitoring. Level is controlled by  
booth level control (11)  
25. Master output: Level is controlled by master level control (10)  
26. REC output: Record out connects to tape recorder, mini disk recorder, etc. to  
record performance  
27. Voltage selector: Selects between 115V (US) / 230V (EU)  
28. Power cord connector: Input connection for the supplied removable power cord.  
1. Input selector switches: Selects phono or line inputs of channels 1 and 2  
2. Gain control: Controls the input sensitivity of channels 1 and 2  
3. Equalizer: Individual controls for low frequency, midrange, and high frequency  
equalization with (+9/-26 dB)  
overall output level.  
Any changes made to EQ settings will change the  
4. Channel faders: Control the output level of channels 1 and 2  
5. Crossfader: Fades the master output between channels 1 and 2  
6. Level meter: Based upon the meter mode selector (7) setting, the level meter displays  
the master output stereo signal level, or the cue levels of channels 1 and 2  
 
TECHNICAL SPECIFIC ATIONS  
CROSSFADER CLEANING  
Line inputs:  
2 (RCA), 150 mV / 47K ohm  
2 (RCA), 3 mV / 47K ohm  
1 (1/4 inch), 1.6 mV / 600 ohm  
1 (RCA), 1V / 600 ohm  
1 (RCA), 350 mV / 600 ohm  
1 (1/4 inch), 32 - 200 ohms recommended  
20 Hz - 20 kHz, +/- 0.5 dB  
+ 9/-26 dB (Hi, Mid, Low)  
Hi/Mid/Lo +/-12 dB  
The PRO-30 crossfader may need lubrication from time to time. This will extend  
the fader life and eliminate any potential damage due to extended heavy usage.  
Phono inputs:  
DJ mic input:  
Master output:  
Record output:  
Headphone output:  
Frequency Response:  
Tone Control :  
Mic Tone:  
Cleaning Instructions  
1. Remove the crossfader by unscrewing the 2 outer screws (removing the 2  
inner screws will detach the fader from the fader plate) and disconnecting the  
cable from the mixer.  
2. Spray a small amount of cleaner or lubricant into both ends of the fader and  
slide the fader back and forth a few times to spread the fluid evenly throughout  
the fader.  
Gain Control:  
S/N Ratio:  
T.H.D:  
0-20dB  
Less than 80dB  
0.01% at 1KHz  
Dimension(LxWxD):  
Weight:  
8.6” x 12.2” x 3.94” (220 x 310 x 100 mm)  
8 Lbs (3.5 Kg) power supply included  
3. Shake and wipe off excess fluid before re-assembling the fader.  
WARRANT Y  
CROSSFADER REPL ACEMENT  
To replace the cross or channel faders, follow step 1 of the cleaning instructions.  
Replacement parts are availabe from Next! or your local Next! dealer.  
This unit has been designed and manufactured using quality  
components. Therefore, it is warranted to be free from defects in materi-  
als (limited as specified below), and workmanship for a period of thirty  
six (36) months from the original purchase date. During this period, all  
service and parts necessary to repair a defect will be free of charge. This  
limited warranty applies to mechanical parts which are subject to wear  
and tear as specified:  
• Faders, specified durability: 15,000 cycles  
• Rotary potentiometers, specified durability: 10,000 cycles  
• Switches, specified durability: 10,000 cycles  
Consequently, the parts listed above are warranted to be free from  
defects in materials and workmanship for a period of thirty days (30)  
days from the original purchase date.  
FOR THE WARRANTY TO BE VALID, PLEASE COMPLETE THE  
ONLINE WARRANTY REGISTRATION FORM FOUND AT  
WWW.STANTONMAGNETICS.COM  
2821 Evans Street • Hollywood, FL 33020  
 

Sharp Blower AIR BLOWER User Manual
Sierra Computer Drive 2131232 User Manual
Sony Battery Charger BC VM50 User Manual
Sony Blu ray Player BDP S480 User Manual
Sony Clock Radio ICF C760 User Manual
Sony Speaker AIRSA10 User Manual
Sony Stereo System STRDH520 User Manual
Star Micronics Printer SP298 Series User Manual
Subaru Automobile Parts EH722 User Manual
Sub Zero Refrigerator ICBBI 30U User Manual