INSTRUCTIONS
®
FOR INDOOR USE ONLY.
ADULT SUPERVISION RECOMMENDED!
TM
TO GET THE MOST OUT OF
YOUR ZERO GRAVITY MICRO™
WALL RACER PLEASE READ THESE
INSTRUCTIONS FIRST!
NOTE:
USE ON SMOOTH, CLEAN
SURFACES ONLY!
Controller/Charger
Check to make sure contents are
complete:
• 1 Zero Gravity Micro™ Wall Racer
• 1 Controller/Charger
• 1 Instruction Sheet
Zero Gravity Micro™
Wall Racer
CHARGING YOUR ZERO GRAVITY MICRO™ WALL RACER
INSTALL BATTERIES
CLOSE
OPEN
1. Switch
car to
2. Switch
controller/
charger to
“OFF”.
3. Take
out
Battery
Compartment
Door
“OFF”.
charge
nozzle.
Six
1.5-V AA
Alkaline
Batteries or
Rechargeable
Batteries
4. Plug cable
into port
5. Slide
switch on
controller/
charger to
“CHARGE”.
Battery
of vehicle.
Make sure
the arrow is
on top.
Compartment
Controller/Charger
6. Green light
flashing: Vehicle
is charging.
7. When charged,
turn controller/
charger switch
“OFF”.
8. Stow
charge cable
in storage
compartment.
Green light off:
Vehicle is charged.
• Charging should take between 30 and 50 minutes depending on how much charge is left in car.
• NOTE: Do not charge battery immediately after use. Let car battery cool for at least 10 minutes. If charging is not complete in 50 minutes,
replace the charger batteries.
Your Zero Gravity Micro™ Wall Racer has a pre-installed rechargeable
battery inside the vehicle body.
PROBLEMS? Before you return to retailer, please call our HOTLINE for assistance,
1-800-622-8339
DRIVING ON WALLS OR UPSIDE DOWN
To drive on walls upside down you must put the vehicle in
the WALL mode.
NOTE: Avoid driving overhead when other people are
around. Do not stand underneath when driving overhead.
DRIVING ON THE GROUND
The fabric air skirts can be adjusted outward at a 45° angle
to ensure a proper wall suction.
IMPORTANT: The Zero Gravity Micro™ should only be
driven on a smooth, clean, flat surface. Dirt or debris can
get inside the fan and cause damage.
To drive on the ground you must put the vehicle in the
GROUND mode.
The fan will not turn ON, but the headlights will turn on and
the vehicle will drive full function on the ground. (The ground
mode saves the battery charge).
TRIM ADJUSTMENT
A
B
L
R
L
R
L
R
R
L
Place the vehicle in the ground mode and drive forward
without touching the right joystick.
If the vehicle turns to the LEFT, press the Right trim button
until it drives straight (A).
If the vehicle turns to the RIGHT, press the Left trim button
until it drives straight (B).
When finished playing with your Zero Gravity Micro™, remove vehicle from wall.
Turn vehicle OFF. Turn the controller OFF. NOTE: The trim setting will reset when the vehicle and controller are turned off.
PROBLEMS? Before you return to retailer, please call our HOTLINE for assistance,
1-800-622-8339
SPINS
By pushing the joystick on the controller/charger, you can make your Wall Racer spin around on the spot.
RIGHT SPIN
LEFT SPIN
Push the RIGHT joystick to the right to
make the vehicle spin clockwise.
Push the RIGHT joystick to the left make
the vehicle spin counter-clockwise.
TROUBLESHOOTING
PROBLEM
SOLUTION
Vehicle will not run.
1. Power switch is off. Turn on.
2. Controller battery is installed with incorrect polarity. Check the (+) and (-) markings to make sure the
battery is properly aligned.
3. Batteries are drained. Charge batteries and/or install new batteries.
Vehicle does not climb.
1. Over current protection is engaged. Turn vehicle off for 30 seconds then restart.
Vehicle does not drive straight.
1. Check trim.
2. Make sure surface is clean of dirt/dust.
3. Make sure surface is neither too rough or too smooth.
4. Make sure surface is flat.
Vehicle slips climbing the walls.
Vehicle falls off the wall.
1. Clean the tires with a damp rag.
2. Fold up the fabric skirts for a better seal prior to use.
1. Make sure to discharge and then charge again for 30 to 50 minutes.
2. Clean tires and make sure your wall and floor are also clean.
3. Check the fabric skirts for damage. If they have been pulled loose, tape them back on with flexible tape.
4. Make sure surface is flat.
Vehicle will not climb walls.
1. Suction jammed. CALL 1-800-622-8339.
STILL HAVING PROBLEMS? Before you return to retailer, please call our HOTLINE for assistance,
1-800-622-8339
FCC REQUIREMENTS
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures: • Reorient or relocated the receiving antenna. • Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
IMPORTANT BATTERY INFORMATION:
Your Zero Gravity Micro™ is equipped with a Lithium Polymer battery.
WARNING:
•
•
•
•
•
Do not mix old and new batteries.
!
Do not mix alkaline, standard or rechargeable batteries.
Battery installation should be performed by an adult.
Non-rechargeable batteries are not to be recharged.
Rechargeable batteries are to be removed from the toy before
being charged (if removable).
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not leave the toy unattended while charging it.
Battery charging should be done by adults.
Charge the toy on a non-flammable surface and keep it away from flammable items.
Do not expose battery to direct sunlight. There is a risk of the battery exploding, overheating, or igniting.
Do not disassemble, modify, heat, or short circuit the battery.
•
•
Rechargeable batteries are only to be charged under adult
supervision.
Do not place battery in fires or leave in hot places.
Only batteries of the same or equivalent type as
recommended are to be used.
Do not drop or subject to strong impacts.
Do not allow the battery to get wet.
•
•
•
•
Batteries are to be inserted with the correct polarity.
Exhausted batteries are to be removed from the toy.
The supply terminals are not to be short circuited.
Different types of batteries, or new and used batteries are
not to be mixed.
Only charge the battery with the specified Air Hogs® battery charger.
Only use the battery in the device specified by Air Hogs®.
Turn the charger off when the toy’ s battery is charged, and always unplug it from the toy.
Disconnect AC wall chargers from outlets while not in use.
If the toy has been damaged, immediately stop use, unplug, and safely move the toy away from flammable materials.
Follow the manufacturer’ s instructions for charging the toy. Do not charge longer than recommended.
Carefully read the instruction manual and use the battery correctly.
•
Exhausted batteries are to be removed, as they will adversely
affect the performance.
Spin Master Ltd., 450 Front Street West, Toronto, ON M5V 1B6 Canada
TM and © 2008 Spin Master Ltd. Air Hogs ® is a
Contains LiPo battery
Spin Master Inc., PMB #10053, 300 International Drive, Suite 100, Williamsville,
NY 14221, USA
registered trademark of Spin Master Ltd. All rights
reserved. Conforms to product safety standards
ASTM F963, regulatory requirements. Products and
colors may vary. Please retain this information for
future reference. Patent Pending.
pack. Battery pack
must be recycled or
disposed of properly.
Spin Master Toys Far East Limited. Rm #1113, 11/F, Chinachem Golden Plaza,
77 Mody Rd., Tsimshatsui E., Kowloon, HK
Spin Master Toys UK Ltd., Meadowbank, Furlong Road, Bourne End, Bucks,
SL8 5AJ, United Kingdom
MADE IN CHINA.
Spin Master France – 36 rue de Silly – 92100 Boulogne Billancourt – France
North American Consumer Information
Phone: 1-800-622-8339
TM
www.spinmaster.com
Asst. #44317 NEN REV 1
|