Spectra T50e
Quick Start Guide
Documentation
Power cord
Ethernet cable
Rubber feet
Half Height (HH) tape drive sled* -or- Full Height (FH) tape drive sled*
Rack-mount kit
1
Documentation
Open This First
Unpack and
Verify the
Components
USB drive
(in kit)
* The tape drives, the (optional) redundant power supply, and the
library may ship and arrive separately.
Rack-mount Installation Refer to the Spectra T50e Rack-mount Kit Installation Instructions supplied in the Spectra T50e Documentation Kit.
Tabletop Installation You do not need to remove the brackets.
Important! If you remove the bracket, replace the
black screw; do not replace the silver screw.
Warning! The library weighs approximately 34.4 lb. Two people are
needed to move or lift the library.
German: Die Bebliothek hat ein Gewicht vonungefähr 15,6 kg. Zwei
Personen ind notwendig, zu verschieben oder Aufhebung der Bibliothek.
1
Do not set
the library on
the bracket.
Install the
Library
Important! Lift the library only by the two sides—not by the front and back.
Do not stack items on top of the library, as they can restrict robot movement.
Alignment
mark (6x)
Bottom of library
1. Carefully place the library on its side, but do not damage the bracket.
2.Remove the paper backing from the six feet and install as shown.
3. Place the library on a level surface in a well ventilated location.
1
Access bottom
Attach six feet
2
Note: Do not install the feet if you are rack-mounting the library.
Shipping Key Removal Follow these steps to remove the shipping key:
1. Remove the tape securing the shipping key.
Important! Lift
only by two sides.
Remove the
Shipping
Key
2.Pull the key straight up and out of the library.
1
Remove tape
Remove key
Replace tape
3. Place the tape back over the opening in the top of the library.
4.Store the key in the tab at the back of the library.
2
3
L
4
Store key
Tape Drive Installation Install the tape drives from bottom to top.
1. Using a #2 Phillips screwdriver, remove the screws securing the cover plate
1
Remove screws
(or plates), as needed. Important! Do not leave openings uncovered.
2
Install the
Tape Drives
2
Remove plate
2.Remove the plate and store it and the screws for future use.
4
3
2
(remove two plates
for each full-height
tape drive)
3. Remove the tape drive from its protective packaging.
4.While supporting the bottom of the drive sled, slide it into the
empty drive bay. Push the drive sled in until it fits flush against
the chassis and tighten the finger screws.
3
4
Remove tape drive
from packaging
Install tape drive
Note: Refer to the Spectra T50e Tape Drive Installation Instructions for
additional information.
Finger screws
SCSI Follow these steps to connect SCSI tape drives.
Important! Do not mix full-height and half-height tape drives in the
library. Do not daisy-chain LTO-4 SCSI tape drives.
SCSI
Two half-height SCSI
tape drives shown.
1. Connect SCSI cables to the tape drives, as shown.
2.Terminate as follows:
2
1
Terminate
ƒ LTO-3—terminate if it is the last device on the SCSI bus. Every
connector on an LTO-3 tape drive must either be connected to a host,
connected to the next tape drive, or terminated. A maximum of two
LTO-3 SCSI tape drives can be daisy-chained on a single SCSI bus.
Connect SCSI
Connect the
Cables
3
Connect to Host
ƒ LTO-4—terminate the second connector on every tape drive.
Do not daisy-chain LTO-4 tape drives.
3. Connect the other end of the cable to the host computer.
Fibre Channel
Fibre Channel Follow these steps to connect FC tape drives.
1. Remove the protective plugs from the optical connector.
1
Remove plugs
2.Insert one end of the cable into the tape drive (either port).
3. Connect the other end of the cable into the HBA or switch.
Note: See the Spectra T50e Library User Guide for information about
Power
P
dual-port tape drives.
Power Connect the power cord to the library and to an outlet.
2
3
Connect FC
Note: If you purchased an optional redundant power supply, refer to
the Spectra T50e Power Supply Installation Instructions for
information about installing it in the library.
Connect to Host
or switch
Ethernet If you want to use the Ethernet option (remote management or
email notification), connect the Ethernet cable to the library and to the host.
Ethernet
E
•
2009 Spectra Logic Corporation. All rights reserved worldwide. BlueScale, Spectra, SpectraGuard, TeraPack, and the Spectra Logic logo are registered trademarks of Spectra Logic Corporation.
All other trademarks and registered trademarks are the property of their respective owners. Subject to change without notice.
