Source Technologies Printer STM117W User Manual

MODEL : STm.117w  
MOBILE PRINTER  
All specifications are subject to change without notice  
Rev. 1.0  
 
1. Unpacking  
2. Product overview  
Standard  
Front  
Open Button  
Printer  
Battery  
Roll paper  
Paper feed  
button  
Power  
switch  
USB  
SERIAL  
Charger  
Serial Cable  
USB Cable Shielded  
Quick Manual  
Rear  
CD  
Optional  
Battery  
DC Power  
Battery Holder (Cradle) Cigar Jack Charger  
Shoulder strip  
Leather case  
2
3
 
3. Usage and Installation  
3-1 Control panel usage  
3-2 Battery Installation  
Hook  
Button  
Name  
Power  
function  
This button is used to turn the printer on and off.  
When the printer is off, press this button for approximately 3 seconds  
and it will turn on the power. When you press this button in a state  
that the printer is on, the printer will turn off.  
button  
1. Align battery hook as shown in the picture  
2. Push the battery into the printer until it locks in place.  
Paper output can be done manually by pressing this button.  
Additionally, self-testing and Hexadecimal Dumping can be  
processed..  
1. Refer to “3-10” for self test information.  
2. Refer to the service manual regarding Hexadecimal Dumping.  
Paper  
Feed  
Button  
NOTE  
As the battery is not charged at the time of your purchase, charge the  
battery prior to using the printer  
(Battery charger or Cradle can be used to charge)  
1. If the Batt, LED are Lit, the battery is fully charged.  
2. If you can hear beeping sound and LED light is turned off, it means  
that the battery is at the lowest level.  
3. If the battery is not charged at all, the printer turns off  
automatically.  
Battery  
Status  
Lamp  
CAUTION  
Risk of explosion if battery is replaced by an incorrect type.  
Dispose of used batteries according to the instructions  
If the red light is turned on, it means there is no paper roll or the  
paper cover is open.  
Error  
Lamp  
4
5
 
3-3 Battery charging  
3-4 Battery charger usage  
Optional  
Lamp  
Lamp  
DC Jack  
1. Insert the battery into the battery holder as shown above  
2. Connect the DC JACK to the power electrical outlet.  
3. Plug the power code into the electrical outlet.  
1. Be sure that the printer is turned off  
2. After open the DC JACK cover, insert DC JACK into the printer.  
3. Plug the power code to electrical outlet.  
4. Once the charging is completed, remove the battery from the holder.  
3-3-1 The status of lamp in charging  
3-4-1 The status of lamp in charging  
Status  
charging  
Red  
charging complete  
Green  
Status  
charging  
Red  
charging complete  
Green  
Charging Lamp  
Charging Lamp  
NOTE  
1. Unless the exclusive charger is used provided by the manufacturer, the printer  
can be damaged, and the manufacturer is not liable for the consequential damage.  
NOTE  
In the case the battery is not fixed properly in the holder, the red lamp will be  
blinking, Then, extract and reinsert the battery.  
2. Before removing the battery, make sure that power is turned off.  
3. Printer does not work in the status of being connected with charger only.  
4. The battery should be installed to operate printer.  
5. While charging, do not turn on the power.  
6. Do not operate the print while charging the battery.  
7. Do not connect the charger while the printer is operated.  
6
7
 
3-6 Roll Paper installation  
3-5 Usage of Cigar Jack Charger for charging  
Optional  
Printer  
Press the PUSH button to open  
the paper cover  
Insert the paper in the right  
direction  
1
3
2
4
Battery holder  
Connect the car cigar JACK charger into the printer or battery holder.  
Input  
12 ~ 24V  
Output  
8.4V 0.8 ~ 1.2A  
Pull a short length of paper out of  
the printer and close the cover.  
Tear off the additional paper using  
tear bar.  
NOTE  
Use the Cigar Jack offered by the manufacturer  
.
8
9
 
3-7 Leather case usage  
Optional  
3-8 Self Test  
Turn off the power pressing the  
power button for approximately  
3 seconds.  
While you are pressing the FEED  
button, press the power button  
Open the leather case  
Place the printer into the leather  
case  
1
3
2
1
2
3
NOTE  
1. To print ASCII pattern additionally,  
press the Feed button once more  
2. After printing ASCII pattern, the  
self test will be finished automatically.  
3. If the Feed button is not pressed  
to print ASCII pattern, self test will be  
finished automatically after 30 seconds.  
The printout is produced.  
Close the Velcro and stick the  
cover.  
10  
11  
 
4. Peripherals connection  
This product can communicate with other devices via Wifi(802.11b/g)  
communication and cable.  
The sample of self test printout  
4-1 Wifi(802.11b/g) Connection  
1. The Printer can be connected to devices equipped with wifi(802.11b/g)  
communication capacity (PDAs, PCs, etc.)  
2. Use the wifi(802.11b/g) connection function supported by the device to  
connect to the printer.  
NOTE  
When the printer is installed initially or when you face a problem, you can run the  
self test and check the information about  
Refer to the wifi(802.11b/g) Manual for more details on connection.  
-Control Circuit, Mechanism, Print Quality, ROM Version  
After checking with self-test and no issues are found, you can examine other  
devices and software. This function is working independent of devices and software.  
Motor protection from being overheated  
The motor should be stopped and cooled about more than 30 seconds after  
continuous printing 1.5 meter  
12  
13  
 
5. Printer cleaning  
If the interior of the printer is dusty, printing quality can lowered.  
In such a case, follow the instructions below to clean up the printer.  
4-2 Interface Cable Connection  
NOTE  
1. Make sure to turn the printer power off prior to cleaning  
2. Regarding print head cleaning, as the print head sets very hot during  
printing, turn off the printer power and wait approximately 10 minute before  
commencement.  
3. When cleaning the print head, take care not to touch the heated portion of the  
print head. The print head subject to be damaged by static electricity.  
4. Take care not to allow the print head to become scratched and /or  
damaged in any way.  
Serial  
USB  
1. Connect USB or Serial cable into the cable connector on the printer.  
NOTE  
Use the cable offered by the manufacturer (USB, Serial)  
2. Connect the interface cable into the USB or Serial port of the device  
(PDA, PC, etc.)  
1. Use an applicator swab moistened with an alcohol solution to clean the print  
head and remove any dusts.  
2. Once the cleaning is completed, insert paper roll into the printer few minutes  
later and close the printer cover.  
Preventing Overheating  
To prevent the motor from overheating, continuous driving of the printer  
should be 1.5 m or less in print length. Set the pause time for 30 seconds  
or more after driving the printer.  
14  
15  
 
6. Pritner Specification  
6-1 Specification  
Battery  
Size  
Battery type  
output  
Li-ion  
Printing Method  
Printing Speed  
Resolution  
Direct Thermal  
7.4V, 2200mAh  
3hours 40min  
149 X 161 X 69  
5.8 X 6.3 X 2.7  
0.53kg (With Battery)  
-10 ~ 50℃  
80mm/sec  
Charging time  
W X D X H(mm)  
W X D X H”  
203 DPI X 203 DPI  
Character  
CPCL  
7 Different Font Size (12~48pt)  
Font A (12X24), Font B (9X17)  
Font A : 48pt , Font B : 64pt  
ESC/POS  
Weight  
Character per line  
Character set  
Temperature  
operation  
storage  
ALPHA NUMERIC Character, Extension  
Character  
-20 ~ 60℃  
Barcode  
EAN-8, EAN-13, Code39, ITF, UPC-A, UPC-E,  
Codabar, Code93, Code128, PDF417(2D),  
MAXICode (2D)  
Humidity  
operation  
storage  
35 ~ 95%  
10 ~ 95%  
Emulation  
Driver  
ESC/POS, CPCL, Commanl Compatible  
Window CE 4.2&5.0, Window Mobile 5.0  
Sensor  
Paper End Sensor , Gap Sensor , Cover Open  
Sensor , Black Mark Sensor  
Paper  
paper type  
width  
Thermal Paper / Label  
50mm ~112mm  
0.06mm ~ 0.09mm  
Max. Φ56mm  
thickness  
External Diameter  
Internal Diameter  
TPH  
12.5mm +/-0.5mm  
50km  
Reliability  
Battery  
Continuous printing: 48min  
Standby: 12hours  
Printing length: 160m  
Communications  
Battery Charger  
Serial(RS-232C), USB, Wireless Lan *802.11b/g  
input  
AC100~240V, 50/60 Hz  
8.4V , 800~1400mA  
output  
16  
17  
 
7. CPCL Command Compatibility  
Compatibility  
Graphics  
BOX  
NOTE  
Compatible with only  
Partially  
Not  
Compatible  
LINE  
commanders provided  
by the manufacturer.  
Compatible  
Compatible  
INVERSE-LINE  
PATTERN  
GRAPHICS  
PCX  
x
Compatibility  
Printer Commands  
PRINT  
Compatibility  
Advanced Commands  
CONTRAST  
TONE  
X
FORM  
JOURNAL  
JUSTIFICATION  
PAGE-WIDTH  
PACE  
UNITS  
Comments  
Compatibility  
TEXT  
NO-PACE  
WAIT  
TEXT  
FONT-GROUP(FG)  
TEXT CONCATENATION  
MULTILINE(ML)  
COUNT  
REWIND  
X
TENSION  
SPEED  
X
SETSP  
SETMAG  
ON-OUT-OF-PAPER  
ON-FEED  
PREFEED  
X
SCALABLE TEXT  
Linear Bar Codes  
BARCODE  
X
Compatibility  
POSTFEED  
PRESENT-AT  
COUNTRY/CODE PAGE  
FORMAT FILES  
BEEP  
BARCODE-TEXT  
Two-Dimensional Bar Codes  
PDF417 (PORTABLE DATA FILE)  
MAXICODE  
Compatibility  
X
QRCODE  
CUT  
DATAMATRIX  
GS1(RSS)  
X
PATIAL-CUT  
MCR  
18  
19  
 
8.Certification  
FCC Information  
Compatibility  
Line Print Mode  
SETLP  
This device complies with part 15 of the FCC Results. Operation is  
subject to the following two conditions:  
SETLF  
Moving With X and Y Coordinates  
(1) This Device may not cause harmful interface, and  
(2) This device must accept any interference received, including  
interference that may cause undesired operation.  
LMARGIN  
SETBOLD  
SETSP  
Special ASCII Characters  
SETFF  
NOTE  
This equipment has been tested and found to comply with the limits for CLASS  
B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference when the equipment  
is operated in a commercial environment. This equipment generates, uses and  
can radiate radio frequency energy and, if not installed and used in accordance  
with the instuctions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and  
on, the user is encouraged to try correct the interference by one or more of the  
following measures:  
SET-TOF  
SETLP-TIMEOUT  
1.1. Reorient or relocate the receiving antenna.  
1.2. Increase the separation between the equipment and receiver.  
1.3. Connect the equipment into an outlet on a circuit different from  
that to which receiver is connected.  
1.4. Consult the dealer or experienced radio/TV technician for help.  
WARNING  
Changes or modifications not expressly approved by the manufacturer could void  
the user's authority to operate the equipment.  
20  
21  
 
9. Setting up the software  
Please refer to the programming manual included in CD.  
CAUTION  
Antenna shall be mounted in such a manner to minimize the potential  
for human contact during normal operation. The antenna should not  
be contacted during operation to avoid the possibility of exceeding the  
FCC radio frequency exposure limit.  
The device meets the FCC requirements for radio frequency (RF)  
radiation exposure in the standard body worn configuration with no  
minimum configuration. In this configuration, which applies whether  
the belt clip or shoulder strap is used, the face of the printer from which  
paper is transported is facing away from the user’s body. The standard  
configuration must always be used when the printer is body worn.  
22  
23  
 

Shark Vacuum Cleaner NV350W User Manual
Sharp Projector XV Z20000 User Manual
Sony Portable Speaker GS70PC User Manual
Sony Tablet SVJ2021 User Manual
Speco Technologies DVR D16WRS User Manual
Speco Technologies Security Camera CVC 8WMPDV User Manual
Spectra Laser Level GL622 User Manual
Spin Master Motorized Toy Car Triple Booster User Manual
Stiga Lawn Mower 13 2533 45 User Manual
Sylvania DVD Player DVL700E User Manual