3-278-786-12(1)
Searching for the Correct Code
This guide shows you how to set the Remote
Commander to operate your components.
Setting Up the Remote Commander
About setting up the Commander
Remote Button Descriptions
Component code numbers /
Números de código de componentes
English
1
Startup Guide
It is possible to find a code number available
for a component that does not have one in
“Component code numbers.”
SET
INPUT
3
2
SET indicator
General
TV
CBL/SAT
The Commander is set up at the factory to operate Sony brand
components. However, even if you intend to use the Commander
with a Sony component, you may still need to set up the
Commander for it, depending on the component.
To set up the Commander to use with other (non-Sony)
manufacturers’ components, or to use with a component that is not
preset at the factory, you will need to follow the instructions in this
manual to preset the Commander with the correct code number for
your component. (See “Startup Guide” and “Component Code
Numbers”.)
1 To set up the Commander.
5 Volume up: +
SET
INPUT
Digital Satellite Receiver, Cable box, TV
The following tables show brand names and their corresponding code numbers.
Enter the code number
Before starting the Search function
Set each component to the following status so
that the Search function works effectively.
TV
CBL/SAT
Volume down: –
Español
6 To mute the volume on a
TV.
Example: To set up a Philips Digital Satellite Receiver
ENT
CH
Sintonizador de recepción vía satélite digital, adaptador para cablevisión, televisor
Las tablas que se presentan a continuación muestran las marcas y los números de código
correspondientes.
4
3
VOL
7 To turn the power of a
selected component on or
off.
TV, DVD Home Theater: Power-on
Other components: Power-off
Find the code number in “ Component code numbers.”
1
Remote
Commander
MUTING
RECALL
ENT
CH
Press and hold the SET button for 2 seconds or more to set a Component Code.
Mantenga presionado el botón SET durante 2 segundos o más para ajustar un
código de componente.
VOL
* If any of these components are assigned to any
of the Component Select buttons, you can set a
component code using the Search function.
8 Component Select Buttons.
Press to select a component
to operate.
MUTING
RECALL
SET
Component Select button Preset component(s) Factory setting
1 Press and hold SET for more than two seconds. The SET indicator
lights up.
TV
CBL/SAT
Code No. / N.º código
ENT
c
c
c
TV
TV
Sony TV
Operating Instructions
2 Press the appropriate Component Select button. The SET indicator
lights up.
CBL/SAT
Cable box/Digital
satellite receiver/TV
Sony Cable box
About tactile dots
The number 5 button and CH + each have a tactile dot for convenient use.
Manual de instrucciones
(parte posterior)
Digital Satellite Receiver /
Sintonizador de recepción vía satélite digital
3 Press CH + (or CH –) and 1 in turn until the component reacts as
follows:
Note
Note on the VOL +/– and MUTING buttons
The Commander can be set up to operate only one component per button –
unless their code numbers happen to be the same. For example, you cannot set
up the Commander to operate a Sony TV and a Panasonic TV simultaneously
(because they use different code numbers).
The Commander controls or mutes the TV’s volume when you select a visual
component. The Commander outputs the signals to control or to mute the TV
volume when you have set one of these components.
DirecTV
Dish Network HDTV Tuner
TV: Power-off
Other components: Power-on
Brand / Marca
Sony
DirecTV
Code No. / N.º código Code No. / N.º código Code No. / N.º código
3001, 3011, 3012
—
—
—
—
If your component is not listed, try the search method described in “Searching
3013, 3017, 3018,
for the Correct Code.”
3019, 3023, 3024
Press CH + to go to the next code number.
Press CH – to go back to the previous code number.
Dish Network
—
3010, 3014, 3025
—
Operating a TV
Installing the batteries
Push open the battery compartment and insert two size AA (R6)
batteries (not supplied).
Be sure to align the + and – on the batteries with the + and – in the
battery compartment.
GE (General Electric) 3019
—
—
Set the Remote Commander for code input mode.
2
2 To change the input mode.
3, 4 and 9
Hitachi
Hughes
Humax
JVC
3005
3004
—
—
—
—
—
—
—
3402
—
The SET indicator flashes once after the numbers have cycled
once.
One cycle means, for example, that the commander has finished
searching for all the code numbers allocated to the component.
b
Press and hold SET for more than two seconds.
RM-EZ4
To change the channel.
3010, 3014
The SET indicator lights up.
q; CH +: Channel up.
Magnavox
Panasonic
Philips
Proscan
RCA
Samsung
Sylvania
Toshiba
Usdigital
3018
3003
3018
3002, 3007, 3019
3002, 3007, 3019, 3021
3017, 3022
—
3006
—
—
—
—
—
—
—
—
—
—
—
—
—
—
CH –: Channel down.
©2007 Sony Corporation Printed in China
1
2
qa To operate the JUMP, FLASHBACK or CHANNEL RETURN function on
4 Press ENT.
2
Press the appropriate Component Select button.
the TV.
3
The SET indicator and the Component button turn off.
If the SET indicator flashes five times before turning off, setup is
incomplete. Start over from Step 3.
—
CBL/SAT
3404
3403
—
Operating a cable box
3
If the component does not operate properly, repeat steps 1 to 4 and
search for another code.
2 To change the input mode.
3, 4 and 9
3401
4
To change the channel.
Enter the code number.
4
If you still cannot get the Commander to work properly, see
“Troubleshooting.”
English
q; CH +: Channel up.
Cable box / Adaptadores para cablevisión
When to replace the batteries
CH –: Channel down.
b
b
b
Before replacing the batteries, have new ones ready beforehand.
Under normal conditions, batteries will last up to one year. If the Commander
does not operate properly, the batteries might be worn out. Replace the
batteries with new ones.
Brand / Marca
Code No. / N.º código
qa To toggle the current/previous channel.
5
For the customers
in the U.S.A.
Sony
ABC
3101
9405
3107, 3110
3107
3107
3105
3107
3105
3107
3107
3107
3107
3107
3107
Notes
Adelphia
Advanced Newhouse
Altrio
Americast
Atlantic Broadband
Bell South
Blue Ridge
Brigth House
Cablevision
Charter
Operating a Component
• In some cases, you can turn the cable box on/off by pressing CH + or CH – on
the Commander.
Finish setting.
5
Notes
WARNING
ENT
1 Press the appropriate Component Select button on the
Commander.
• If your cable box can control volume, be sure to set its volume control to a
moderate level. If the volume on the cable box is turned down completely,
you will not be able to adjust your TV’s volume with the Commander.
• Replace both batteries with new ones.
• Do not take more than 3 minutes to replace the batteries; otherwise, your
code number settings will be erased.
This equipment has been tested and
found to comply with the limits for
a Class B digital device, pursuant to
Part 15 of the FCC Rules. These
limits are designed to provide
reasonable protection against
harmful interference in a residential
installation. This equipment
Press ENT.
TV
CBL/SAT
•
Do not mix old batteries with new ones, or mix different battery types together.
• If the electrolyte inside the battery should leak, wipe the contaminated area of
the battery compartment with a cloth and replace the old batteries with new
ones. To prevent the electrolyte from leaking, remove the batteries when you
plan to not use the Commander for a long period of time.
2 Aim the Commander directly at the component.
Operating a digital satellite receiver
Let's check
v
3 Press the button for the function you want to use.
2 To switch the output of the digital satellite receiver to the TV. (When
you connect a TV cable or antenna to the receiver, the output switches
between TV and satellite programs.)
3, 4 and 9
Comcast
Cox
Turn on the component you want to set up.
6
7
8
generates, uses and can radiate
radio frequency energy and, if not
installed and used in accordance
with the instructions, may cause
harmful interference to radio
communications. However, there is
no guarantee that interference will
not occur in a particular
installation. If this equipment does
cause harmful interference to radio
or television reception, which can
be determined by turning the
equipment off and on, the user is
encouraged to try to correct the
interference by one or more of the
following measures:
• Reorient or relocate the
receiving antenna.
• Increase the separation between
the equipment and receiver.
Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an
experienced radio/TV
technician for help.
See “Remote Button Descriptions” for complete descriptions of
the buttons on the Commander.
General Instrument
3103, 9002, 9003, 9004, 9005, 9006, 9007, 9008, 9018,
9022, 9043, 9044
Press the same Component Select button in step 3 again.
To change the channel.
GNC
3105
Notes on Using the Remote Commander
Basically, use this Commander in the same way as the
Commanders supplied with your components.
•Using this Commander will not increase the functions of your
components. The functions of the Commander are limited to
the functions of the components themselves. For example, if
your TV does not have a MUTING function, MUTING on this
Commander will not function with your TV.
•Some functions of the component may not work with this
Commander.
•If your cable box can control volume, be sure to set its volume
to a moderate level. If the volume on the cable box is turned
down completely, you will not be able to adjust your TV’s
volume with the Commander.
Troubleshooting
If you have problems setting up or using the Commander:
Hamlin
Illico
9022, 9023, 9024, 9025, 9026
3107
q; CH +: Channel up.
Aim the Remote Commander at the component and press
1 on the Remote Commander.
CH –: Channel down.
Jerrold
3103, 9002, 9003, 9004, 9005, 9006, 9007, 9008, 9018,
qa To tune to the last tuned station.
•
When setting up the Commander, carefully go through the procedures
described in “Startup Guide.” If the code that is listed first for your component
does not work, try other codes for that component – in the order in which they
are listed. If all the codes fail to work (or if your component is not listed in this
manual), try using the procedures in “Searching for the Correct Code.”
9022, 9043, 9044
Memorex
Motorola
NET
3106
3103, 3110, 3111
9042
v
Was the component turned off?
Oak
9027, 9028, 9029
Pace
3107
• Make sure that you are aiming the Commander directly at the component,
and that there are no obstructions between the Commander and the
component.
• Make sure the batteries you are using are not worn out, and that they are
inserted correctly.
• Check that the appropriate TV or CBL/SAT button is pressed.
• Check that the component has infrared remote capability. For example, if
your component did not come with a remote control, it probably is not
capable of being controlled by the Remote Commander.
• Should any problem persist, reset the Commander to the factory setting by
pressing the 1, INPUT and VOL – buttons simultaneously.
Specifications
Yes
No
Check that the other buttons function.
Panasonic
Paragon
Philips
9019, 9020, 9021
3106
3104
Operable distance
Approx. 7 m (23 ft) (varies depending on component
manufacturer)
Start over from Step 2 above, using another code number.
Pioneer
Pulsar
3107, 9014, 9015
3106
If you still cannot get the Remote Commander to work properly after
trying all the codes listed for your component, try the search method
described in “Searching for the Correct Code.”
Power requirements Two size AA (R6) batteries (not supplied)
Battery life
Dimensions
Mass
Approx. 1 year (varies depending on frequency of
button use - up to approx. 300 times per day)
Approx. 63 × 149 × 30 mm (w/h/d)
Regal
9022, 9023, 9024, 9025, 9026
Rodgers
Runco
3107
3106
•
(2 1/2 × 5 7/8 × 1 3/16 in)
Scientific Atlanta
Seren
3102, 3107, 3108, 3109, 9009, 9010, 9045, 9046
3107
Approx. 86 g (3.0 oz) (not including batteries)
Sigecom
Susquehanna
Time Warner
Tocom
3107
3107
3107
9016, 9017, 9043
3106
• If the SET indicator flashes five times before lighting up, it means that the setup is incomplete.
Confirm the code number and start over from Step 4.
• If you do not input anything into the Remote Commander within 20 seconds between each step, or if you
press SET while setting the code number, the setup procedure will be canceled. Start over from Step 2.
Design and specifications are subject to change without notice.
For the customers in the U.S.A.
Customer Support Information
You are cautioned that any
changes or modifications not
expressly approved in this manual
could void your authority to
operate this equipment.
Toshiba
After you have read through this manual, if you still cannot get the Remote
Commander to work properly, call the Sony Customer Support Helpline at
1-800-822-2217.
Continued on reverse side / Continúa en el reverso
|