Installation and Operation Instructions for the following model:
BRCSDP16
OUTDOOR AND INDOOR DOME HOUSING
CONTENT OF BOX:
(1) Housing
(1) Supplied Parts
(1) Power Connector (Heater/blower)
(1)Toolhead Driver
(1) Operation Instruction Manual
81-IN6584 03082011
If you wish to provide a single power transformer it is
recommended that:
WIRING
1. Be certain that you know the total power consumption of
the housing Heater (25 watts) + Blower (1 watt) + camera
pan/tilt (25 watts).
WIRING INSTRUCTIONS (OUTSIDE OF HOUSING)
BNC
2. Check the supplied wiring chart (see below) to be sure that
you have the proper gauge wire for the distance that you
intend to run your power wires.
(Large)
Power
3. Bring power to the 3 and 4 position of the power connector
(yellow and green wire).
(Small)
Alarms
4. Jumper from the 1stposition to the 3 rdposition and from
the 2nd position to the 4th position of the terminal block.
Be careful not to short between the yellow and green wires.
Wiring Color Code Power and Control Inputs
Green
POWER
Add 2 jumpers for
single power input
Yellow
1
2
3
4
Camera Power (24 VAC)
Camera Power (24 VAC)
Red
Wires from
Dome
Orange
Heater and Blower Power (24 VAC) Yellow
Heater and Blower Power (24 VAC) Green
CONTROL
1
2
3
4
Alarm 1
Blue
AC
24V
Power
Supply
Side
Alarm 2
Alarm 3
Common
Violet
Gray
White
Orange
Red
WIRING INSTRUCTIONS (INSIDE OF HOUSING)
1. The internal power supply provides 12Vdc power.
NOTE: The total power consumption for the heater
and blower, PLUS the camera you choose,
need to be added together.
2. Plug in right angle power plug to back of camera;
plug provides 12Vdc to camera.
In this example, a 60VA AC24V is required.
24V AC Wiring Distances
The following are the recommended maximum distances for 24 VAC
with a 10% voltage drop (10% is generally the maximum allowable
voltage drop for AC powered devices).
Wire Gauge
Total vA
consumed
20
18
16
14
12
10
-
22
250
120
89
400 600 960
-
-
12DC
5.5
10
20
30
40
50
60
70
80
Make all connections
to the camera.
–
180 300 480 800 1300
-
+
141 225 358 571 905 1440
90 130 225 350 525 830
70 112 179 285 452 720
65
OPTIONAL
44
1
2
3
4
Alarm 1
Alarm 2
Blue
56
47
40
34
90
75
64
55
143 228 362 576
119 190 301 480
102 163 258 411
35
Violet
Gray
White
29
Alarm 3
25
Common
85
140 215 340
31
INSTALLING THE CAMERA
1
Install the Sony BRC700 pan/tilt onto the quick release
bracket using the (2) screws and washers provided with the
camera (Figure 4).
2
Place the Sony BRC700 pan/tilt and quick release bracket in
the housing, sliding the three open screw slots over the screws
in the housing. Slide the bracket back, then tighten the captive
screw on the bracket (Figures 5 and 6).
Figure 4
Figure 5
Figure 6
IMPORTANT SAFEGUARDS
SAFETY PRECAUTIONS
1
2
3
Read Instructions - All the safety and operating instructions
should be read before the unit is operated.
CAUTION
Retain Instructions - The safety and operating instructions
should be retained for future reference.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
Heed Warnings - All warnings on the unit and in the operat-
ing instructions should be adhered to.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
4
5
6
Follow Instructions - All operating and user instructions
should be followed.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
Electrical Connections - Only a qualified electrician should
make electrical connections..
The lightning flash with an arrowhead symbol, within
an equilateral triangle, is intended to alert the user to the
presence of non-insulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
Attachments - Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
7
8
Cable Runs - All cable runs must be within permissible
distance
Mounting - This unit must be properly and securely
mounted to a supporting structure capable of sustaining the
weight of the unit. Accordingly:
The exclamation point within an equilateral triangle is
intended to alert the user to presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
!
a. The installation should be made by a qualified installer.
b. The installation should be in compliance with local
codes.
UNPACKING
c. Care should be exercised to select suitable hardware to
install the unit, taking into account both the composition
of the mounting surface and the weight of the unit. Be
sure to periodically examine the unit and the supporting
structure to make sure that the integrity of the in stalla-
tion is intact. Failure to comply with the foregoing
could result in the unit separating from the support
structure and falling, with resultant damages or injury to
anyone or anything struck by the falling unit.
Unpack carefully. Electronic components can be damaged if improperly
handled or dropped. If an item appears to have been damaged in s-hip
ment, replace it properly in its carton and notify the shipper.
Be sure to save:
1
The shipping carton and packaging material. They are the safest
material in which to make future shipments of the equipment.
2
These Installation and Operating Instructions.
SERVICE
If technical support or service is needed, contact Sony at the following
number:
TECHNICAL SUPPORT
8:15AM to 7:30PM (Eastern Time)
1-800-883-6817
Note:
Please note that to achieve the increased depth with the aspheric design for optimal camera lens to
capsule orientation, the capsule is slightly angled around the highest section. This creates a ”line’, visible to
the naked eye, around the upper most section of the capsule. This“line”serves as the geometric center line
used to insure proper camera placement. It is not typically seen by the camera. However, Sony RZ series
PTZ cameras are able to tilt up above the horizon to 25°, this wide range of tilt motion at a wide angle view
may cause this line to be captured in the image.
Warranty
For warranty information on this and other Sony Security Systems Products, please visit:
|