4-156-141-11(1)
How to use the remote
and microphone for an
iPod (See fig. -)
Specifications
Receiver
Type:
Closed, dynamic
You can control a connected iPod
product.
Operating Instructions
Manual de instrucciones
Driver unit:
9 mm, dome type (CCAW)
Stereo
Parts and controls
Power handling capacity:
100 mW (IEC*)
Impedance:
Volume +
Increases the volume of the connected
iPod product.
Headphones
16 Ω at 1 kHz
Center button
Sensitivity:
Plays/pauses a track of the connected
iPod product with a single press. Skips
to the next track with a double press.
Skips to the previous track with a triple
press. Starts the “VoiceOver*” feature
with a long press (if available).
Volume –
100 dB/mW
Frequency response:
6 – 23,000 Hz
Cord:
Plug:
Mass:
1.2 m (3.9 ft), Litz cord
Y-type
Gold-plated L-shaped stereo
mini plug
MDR-EX38iP
Decreases the volume of the connected
iPod product.
Microphone
Approx. 3 g (0.11 oz)
without cord
©2009 Sony Corporation Printed in Thailand
Microphone
Compatible products
You can use the unit with the following
models.
Open circuit voltage level:
– 42 dB ( 0dB=1V/Pa)
Supplied accessories
Earbuds (S × 2, M × 2, L × 2)
Cord adjuster (1)
English
iPod nano (4th generation)
iPod classic (120 GB)
iPod touch (2nd generation)
iPod shuffle (3rd generation)
Stereo headphones
Carrying pouch (1)
* IEC = International Electrotechnical
Commission
Design and specifications are subject
to change without notice.
Features
* Availability of the “VoiceOver” feature
depends on iPod model and its software
version.
Easy-to-use remote control for iPod
only
Clear and rich sound with deep bass
Convenient cord adjuster supplied
How to install the earbuds
correctly (see fig. )
If the earbuds do not fit your ears
correctly, low-bass sound may not be
heard. To enjoy better sound quality,
change the earbuds to another size, or
adjust the earbuds position to sit on
your ears comfortably and fit your ears
snugly.
If the earbuds do not fit your ears, try
another size. Confirm the size of the
earbuds by checking color inside (see
fig. -).
When you change the earbuds, turn to
install them firmly on the headphones
to prevent the earbud from detaching
and remaining in your ear.
Precautions
Please keep your headphones clean
at all times especially inside the
rubber earbud. (see fig. )
If any dust or ear wax inside the
earbud, you may experience some
listening difficulties.
How to use
Wearing the headphones
(see fig. )
Wear the earpiece marked in your
right ear and the one marked in
your left ear.
There is a tactile dot on the unit
marked to distinguish the left side.
Listening with headphones at high
volume may affect your hearing. For
traffic safety, do not use while
driving or cycling.
The earbuds may deteriorate due to
long-term storage or use.
How to use the cord slider
(see fig. -)
Move up and down to change the split
position of the cord.
Install the earbuds firmly onto the
headphones. If an earbud
accidentally detaches and is left in
your ear, it may cause injury.
Earbud sizes (inside color)
Small
SS*
Large
Note on static electricity
In particularly dry air conditions, mild
tingling may be felt on your ears. This
is a result of static electricity
accumulated in the body, and not a
malfunction of the headphones.
The effect can be minimized by
wearing clothes made from natural
materials.
S
M
L
How to use the supplied
cord adjuster
(see fig. -)
You can adjust the cord length by
winding the cord on the cord adjuster.
(The cord can be wound to the cord
adjuster up to 50 cm. If you wind
more, the cord comes off from the cord
adjuster easily.)
(Red)
(Orange) (Green) (Light blue)
* This size is optional and available at
purchase.
Sectional View
To detach an earbud
(see fig. -)
While holding the headphone, twist
and pull the earbud off.
EP-EX10A is available (sold
separately) as optional replacement
earbuds.
EP-EX10A offers 4 types of the
earbuds: SS, S, M and L.
Tip
If the earbud slips and cannot be detached,
wrap it in a dry soft cloth.
1
2
Wind the cord.
Colored parts
Push cord into slot hole to
secure in place.
To attach an earbud
(see fig. -)
Note
Push the parts inside of the earbud into
the headphone until the projecting
part of the headphone is fully covered.
On copyright
Do not wind the plug or split section of the
cord, as it will strain the cord and may cause
a wire break.
iPod is a trademark of Apple Inc.,
registered in the U.S. and other
countries.
Cleaning the earbuds
Remove the earbuds from the
headphones, and wash them with a
mild detergent solution.
|