4-180-193-11(1)
Setting up your TV
LCD
To watch TV
Digital Color TV
Setup Guide (Operating Instructions)
Additional Information
Sony Customer Support
United States
Canada
1.800.222.SONY 1.877.899.SONY
Please Do Not Return
the Product to the Store
KDL-55HX800 / 46HX800 / 40HX800
XBR-52HX909 / 46HX909
Table of Contents
Using a Wall-Mount Bracket........................................................................................................15
To use the TV features................................................................................................................16
•
Operating instructions are built into your BRAVIA TV. Refer to “To use i-Manual” for operation (page 17).
• Retain this manual for future reference.
The BRAVIA® Full HDTV Experience
®
Thank you for choosing Sony! Your new BRAVIA TV
•
•
Receive over-the-air HD broadcasts with an HD-
quality antenna connected directly to the back of your
TV.
information on antenna selection and setup.
Discover the wealth of entertainment now available
on super-high resolution Blu-ray Disc™ player and
opens the door to the “Full HDTV Experience.” This
document will help you get the most out of your TV.
Please take a moment to register your TV at:
3 oSthoeruSnondy HD equipment.
Four Steps to a Full HD Experience
Set, Source, Sound, and Setup.
Complete the high-definition experience with a
BRAVIA Sync™ surround sound system or A/V
receiver from Sony.
1 Set
Now that you have made the best selection in LCD TV
technology, be sure to remove all accessory contents
from the packaging before setting up your TV.
4 Setup
Install your TV and connect your sources. See page 8 for
sample connection diagrams.
2 Source
To experience the stunning detail of your BRAVIA TV,
To help assure the highest quality for your HD experience,
use Sony HDMI (High-Definition Multimedia Interface)
cables.
you need access to HD programming.
•
Upgrade your signal or content source to high-
definition (HD) by contacting your HD service
provider.
To learn more about HDTV, visit:
U.S.A.: http://www.sony.com/HDTV
This TV displays all video input signals in a resolution of 1,920 dots × 1,080 lines.
3
Guidelines for Remote Control
• Point your remote control directly at the IR
sensor located on your TV.
• Make sure that no objects are blocking the
path between the remote control and the IR
sensor on your TV.
• Fluorescent lamps can interfere with your
remote control; try turning off the fluorescent
lamps.
Checking the accessories
AC power cord (1)
Remote control (1)*1
Size AAA batteries (2)
Table-Top Stand (1)*2
Fixing screws for Table-Top Stand
(M5 × 16) (4)
Assembling screws for Table-Top Stand
• If you are having problems with the remote
control, reinsert or replace your batteries and
make sure that they are correctly inserted.
(M5 × 16) (4) (KDL-40HX800 only)
3
Stand rear cover (1)
*
*1 Please refer to the model name printed on the
remote control.
*2 KDL-40HX800 requires assembling.
Refer to other leaflet to assemble the Table-Top
Stand.
*3 For KDL-55/46HX800, the stand rear cover is
factory-attached to the Table-Top Stand.
Inserting batteries into the
remote control
1 Remove the protection sheet.
2 Push and slide the cover upward.
4
Programming the Remote Control
(For RM-ED038 and RM-ED053 remote control users)
Your remote control can be programmed to use other equipment and is pre-programmed to operate
the following Sony equipment.
Function Button Sony Equipment Code Number
DVD
AMP
STB
DVD Player
Receiver
31033
52172
Digital Satellite 01639
Programming Other Equipment
Follow the steps below to program your TV remote control.
2
2
1 Look for the code in the Manufacturer’s Code List (refer to i-Manual) that
corresponds to the equipment you would like to operate with the Sony
remote control. If more than one code is provided, try programming the
first code listed. If your equipment’s code is not listed, visit
2 Press and hold a DVD, AMP or STB function button simultaneously with
INPUT button and release.
4
When in the programming mode, the function button (DVD, AMP, STB)
blinks for approximately 30 seconds until a code is entered.
3
3 Enter the five digit code using
-
while the function buttons
4
(DVD, AMP, STB) are lit. If the code is not entered within 30 seconds,
you must repeat step 2.
~
• Button names may
differ slightly
depending on the
remote control.
4 Press
or ENT to confirm the code. If successfully programmed, the
function button (DVD, AMP, STB) will blink twice, if not, it blinks five
times.
Confirm the Programming
If you can turn your equipment on and off using the green POWER button, the programming is
complete. If not, try the next code listed.
~
• In some cases, you may not be able to program your remote control. If this is the case, use your equipment’s
own remote control.
• Any of the function buttons (DVD, AMP, STB) can be programmed to operate other equipment regardless of
the labeling. For example, if programmed with the correct code, a Blu-ray Disc player can be operated with
the DVD button. This is useful if your equipment does not match any of the labeled buttons.
To reset the remote control to the factory default:
Press SCENE, TV POWER, and simultaneously. The four function buttons (DVD, AMP, STB,
and TV) blink when successfully reset.
5
Setting up your TV
Some TV models are packaged with a detached
Table-Top Stand so you can mount your TV to
a wall right away. If you are not mounting the
TV to a wall, you will need to attach the
Table-Top Stand. You will need a Phillips
screwdriver and the supplied screws to
complete the task. Look for the supplied Table-
Top Stand instruction leaflet.
Attaching the Table-Top
Stand
Refer to the supplied Table-Top Stand
instruction leaflet for proper attachment for
some TV models.
1 Gently slide the TV unit onto the
Table-Top Stand and align the screw
holes.
Be sure to consider the following while setting
up your TV:
•
Disconnect all cables when carrying the
TV.
~
• Do not put stress on the LCD panel or the frame
around the screen.
• Be careful to not pinch your hands or the AC
power cord when you install the TV unit to the
Table-Top Stand.
•
Carry the TV with the adequate number of
people; larger size TVs require two or more
people.
•
Correct hand placement while carrying the
TV is very important for safety and to avoid
damage.
2 Use the supplied screws to attach the
TV unit to the Table-Top Stand.
~
For XBR-52/46HX909 For KDL-55/46/40HX800
• If you use an electric screwdriver, set the
tightening torque at approximately 1.5 N·m
{15 kgf·cm}.
•
Ensure your TV has adequate ventilation,
•
•
•
For best picture quality, do not expose the
screen to direct illumination or sunlight.
Avoid installing the TV in a room with
reflective wall and floor materials.
Avoid moving the TV from a cold area to a
warm area. Sudden room temperature
changes may cause moisture condensation.
This may cause the TV to show poor picture
and/or poor color. Should this occur, allow
moisture to evaporate completely before
powering the TV on.
3 For XBR-52/46HX909 and
KDL-40HX800, after all the screws are
tighten cover the Table-Top Stand with
the supplied stand rear cover.
~
• You can attach the TV to the Table-Top Stand
with the stand rear cover on with the exception of
XBR-52/46HX909 and KDL-40HX800. XBR-52/
46HX909 and KDL-40HX800 must follow the
above instructions.
6
Adjusting the viewing angle (XBR-52/46HX909 only)
This TV can be adjusted within the angles shown below.
6°
0°
3
2
1
4
Remove screw as
shown.
Install screw into the
top screw hole of the
Table-Top Stand.
Slide in.
Lift up and tilt.
~
• Reverse the steps when readjusting the angle back to 0 degrees.
7
Connecting the TV
The following chart shows the high-definition (HD) and standard-definition (SD) video formats
supported by your BRAVIA TV inputs.
* For supported PC formats refer to the i-Manual.
Recommendation of the F type plug
Projection of the inner wire from the
connection part must be less than 1.5 mm.
1.5 mm
8
Shown with a Set Top Box with HDMI
connection
Shown with a Set Top Box with
COMPONENT connection
Set Top Box
Set Top Box
Cable System or VHF/UHF Antenna System
Cable
or
Antenna
(Continued)
9
Shown with HD BRAVIA® Sync™ Basic Connection
*Rear of TV
SAT
(Dish)
HD Cable Box or
HD Satellite Receiver
*A/V Receiver
Cable/
Antenna
*Blu-ray Disc
* Signifies a BRAVIA Sync capable device.
Shown with HD Basic Connection with Home Theater System
Rear of TV
Home Theater System
or
Cable/
Antenna
Cable/SAT
(Dish)
SD Cable Box or
SD Satellite Receiver
Blu-ray Disc/DVD
10
Shown with PC Connection with SD VCR/DVD
Rear of TV
Notebook PC
or
Splitter
PC
VCR
DVD
VCR/DVD Combo
Cable/Antenna
11
Recommended Measures to
Secure the TV
Consider the following measures when
securing your TV to a Stand (not supplied).
Securing the TV
Sony strongly recommends
taking measures to prevent the
TV from toppling over.
Unsecured TVs may topple and
result in property damage,
serious bodily injury or even
death.
1 Secure the Stand for the TV
Make sure the Stand can adequately support
the weight of the TV. Use two angle braces
(not supplied) to secure the stand. For each
angle brace use the appropriate hardware to:
•
Attach one side of the angle brace to the
wall stud.
Attach the other side to the Stand.
Preventing the TV from
Toppling
•
•
•
Secure the TV to a wall and/or stand.
Do not allow children to play or climb on
furniture and TV sets.
Angle brace
(not supplied)
•
•
Avoid placing or hanging items on the TV.
Never install the TV on:
– slippery, unstable and/or uneven surfaces.
– furniture that can easily be used as steps,
such as a chest of drawers.
Stand
•
•
Install the TV where it cannot be pulled,
pushed, or knocked over.
Route all AC power cords and connecting
cables so that they are not accessible to
curious children.
2 Secure the TV to the Stand
Use the optional hardware listed below (not
supplied):
•
M4 × 16 machine screw (screwed into the
TV’s Table-Top Stand)
•
•
A screw or similar (attach it to the Stand)
Rope or chain (strong enough to support the
weight of the TV). Make sure that there is
no excess slack in the rope or chain.
An alternative way to secure the TV is with an
optional Sony Support Belt Kit.
M4 × 16
machine
screw (not
supplied)
Rope or
chain (not
Screw hole on
the Table-Top
Stand
supplied)
Screw
(not supplied)
~
Contact Sony Customer Support to obtain the
optional Support Belt Kit by providing your TV
model name.
•
For United States call: 1-800-488-7669 or visit:
•
For Canada call: 1-877-899-7669
12
3 Anchor the TV to the Wall
Anchor the TV to the wall by using bolts, wall
anchor and chain (or rope).
Organizing the AC power
cord
Anchor bolts (not supplied)
Rope
or
chain
(not
supplied)
Wall-
mount
holes
Wall-anchor
(not supplied)
~
•
KDL-55HX800 is shipped with screws attached
to the rear of the TV. (They are fastened in the
screw holes for wall mounting.) Be sure to
remove the upper two screws prior to installing
the TV on a wall.
•
Securing the TV to the stand without securing
the TV and the stand to the wall provides
minimum protection against the TV toppling
over. For further protection, be sure to follow the
three measures recommended.
13
Running initial setup
Detaching the Table-Top
Stand from the TV
POWER
Remove only the screws marked with
the TV.
on
1 Complete your cable connections
before proceeding with the Initial
Setup.
~
• Do not remove the Table-Top Stand for any
reason other than to install corresponding
accessories on the TV.
Connect the TV to your nearest power
outlet.
• For XBR-52/46HX909 and KDL-40HX800,
remove the stand rear cover prior to detaching the
Table-Top Stand.
2 Check the ENERGY SAVING
SWITCH setting is on (z).
• For KDL-55HX800, when installing the TV on a
wall, remove the four screws from the rear of the
TV. (They are fastened in the screw holes for wall
mounting.) Be sure to store the removed screws in
a safe place, keeping them away from children.
• For KDL-55HX800, when attaching the Table-
Top Stand again, be sure to fasten the four screws
(previously removed) to the original holes on the
rear of the TV.
3 Press POWER on the TV.
When you switch the TV on for the first
time, the Language menu appears on
the screen.
• Do not hold by the stand rear cover while carrying
the Table-Top Stand to prevent dropping the stand
which may cause an injury or damage to the
property.
4 Follow the instructions on the screen.
~
• The ENERGY SAVING SWITCH must be
on (z) to set the clock and obtain program
information for the TV Guide.
• Home mode sets the TV to settings optimized for
home viewing (this setting is ENERGY STAR
compliant).
5 Select Continue to scan for available
channels and enable the TV Guide On
Screen® feature. If you receive channels
from a cable box or satellite receiver
and do not wish to use the TV’s built-in
tuner, select Skip.
Selecting Skip will disable the TV Guide
On Screen feature, which is only
available when the TV’s tuner is used.
~
• If you skip the channel scan while in the setup
menus, TV Guide will be disabled.
14
Using a Wall-Mount Bracket
Installing the TV Against a
Wall or Enclosed Area
Make sure that your TV has adequate
ventilation. Allow enough space around the
TV as shown below. Avoid operating the TV at
temperatures below 41 °F (5 °C).
Your TV can be mounted on a wall using a
Wall-Mount Bracket (not supplied) out of the
box as packaged. If the Table-Top Stand is
attached to the TV, the TV may require
detaching the Table-Top Stand; see “Detaching
Prepare the TV for the Wall-Mount Bracket
before making cable connections.
Installed with stand
7
11
/
inches
8
(30 cm)
3
2
/
inches
8
4 inches
(10 cm)
4 inches
(10 cm)
(6 cm)
For product protection and safety reasons,
Sony strongly recommends that you use the
Wall-Mount Bracket designed for your TV
and the installation should be performed by
a Sony dealer or licensed contractor.
Leave at least this much space around the set.
•
Follow the instruction guide provided with
the Wall-Mount Bracket for your model.
Sufficient expertise is required in installing
this TV, especially to determine the
strength of the wall for withstanding the
TV’s weight.
Installed on the wall
7
11
inches
/8
(30 cm)
4 inches
(10 cm)
4 inches
(10 cm)
Leave at
least this
much space
around the
set.
•
Be sure to use the screws supplied with the
Wall-mount bracket when attaching the
mounting hooks to the TV set.
4 inches (10 cm)
The supplied screws are designed so that
they are 8 mm to 12 mm in length when
measured from the attaching surface of the
mounting hook.
Never install the TV set as follows:
Air circulation is blocked.
Air circulation is blocked.
The diameter and length of the screws differ
depending on the Wall-mount bracket
model. Use of screws other than those
supplied may result in internal damage to
the TV set or cause it to fall, etc.
Wall
Wall
8-12 mm
Screw
(supplied with the
Wall-mount bracket)
~
• Inadequate ventilation can lead to overheating of
the TV and may cause damage to your TV or
cause a fire.
Mounting Hook
Hook attachment on rear of TV
set
•
Be sure to store the unused screws and
Table-Top Stand in a safe place until you
are ready to attach the Table-Top Stand.
Keep the screws away from small children.
~
• Read the supplied Safety Booklet for additional
safety information.
15
To watch TV
To watch programs
Turn on the TV.
1
2
1-2
GUIDE
1 Check the ENERGY SAVING
SWITCH setting is on (z).
2 Press POWER on the TV or on the
remote control to turn on the TV. (You
may use the 1 button located on the
front or back of the remote control.)
OPTIONS
HOME
0-9
ENT
Select a TV channel.
2
To use the Guide
Press GUIDE to display the TV Guide On
Screen to view scheduled programs or to
select a program to watch. Press again to exit
the Guide. Use with 0-9 and ENT to select
digital channels. For example, to enter 2.1,
press
,
,
and ENT.
To use the TV features
Press HOME to display TV Home Menu/
XMB™ to access TV Settings and other
media and network related content.
Press OPTIONS to display a list of convenient
functions and menu shortcuts. The Options menu
items vary based on current input and/or content.
Picture Adjustments
Sound Adjustments
Add to Favorites
Motionflow
Settings
Scene Select
Picture
&
Display
Speakers
Adjust the picture and screen settings
MTS Audio
Press
for:
Picture Adjustments
Ambient Sensor
Screen
Pro Picture Setup
16
To use i-Manual
Your BRAVIA TV comes with an on-screen
manual. To learn more about your TVs features
you can access your i-Manual with the touch of a
button.
1
2
Press i-MANUAL.
1
Press F/f/G/g/ to navigate and
select items.
2
i-Manual
Welcome to i-Manual
"BRAVIA" TV Features
Watching TV
Using the Home Menu
Fun Features with Connected Equipment
Parts Description
Troubleshooting
Index
RETURN Back
x Welcome to i-Manual
x “BRAVIA” TV Features
x Watching TV
x Fun Features with Connected
Equipment
Introduces how to connect and enjoy optional
equipment.
Introduces convenient features such as TV
Guide, Favorites, etc.
x Parts Description
x Troubleshooting
x Using the Home Menu
You can find solutions for your problems.
You can find how to customize your TV
settings, etc.
x Index
~
• Images and illustrations may differ from what you are watching on this TV.
17
Additional Information
Troubleshooting
The TV will indicate any problems with the STANDBY indicator flashing in red.
When the STANDBY indicator is flashing
The self-diagnosis function is activated.
1 Count how many times the STANDBY indicator flashes between each three second
break.
For example, the indicator may flash three times, go off for three seconds, then flash
again three times.
2 Press POWER on the TV to turn it off, disconnect the AC power cord, and contact
Sony Customer Support (information provided on the front cover) with how many times
the indicator flashes.
When the STANDBY indicator is not flashing
1 Check the items in the tables below. (Also refer to “Troubleshooting” in the i-Manual.)
2 If the problem persists, contact Sony Customer Support (information provided on the
front cover).
Condition
Explanation/Solution
Picture
There is no picture (screen • Check the antenna/cable connection.
• Connect the TV to the AC power, and press POWER on the TV.
is dark) and no sound.
• If the STANDBY indicator lights up in red, press POWER on the
remote control.
Tiny black dots and/or
bright dots appear on the
screen.
• The screen is composed of pixels. Tiny black dots and/or bright
dots (pixels) on the screen do not indicate a malfunction.
General
The TV’s power cannot be • Check to see the (z) mark on the ENERGY SAVING SWITCH
is pressed.
turned on.
The TV turns off
automatically (the TV
enters standby mode).
• Check if the Sleep Timer, Timer, or Idle TV Standby is
activated.
• The Auto Shut-off function may be set to On. If Auto
Shut-off is activated and TV receives no signal, the TV will
automatically enter standby mode in 15 minutes. Check Auto
Shut-off is activated under Eco feature of this TV.
The remote does not
function.
• Replace the batteries.
• Your TV may be in SYNC mode. Press SYNC MENU, select TV
Control and then select Home (Menu) or Options to control
the TV.
The TV and its surrounding • When the TV is used for an extended period of time, the TV and
its surround may become warm to touch. This is not malfunction
of the TV.
become warm.
The Parental Lock
password has been
forgotten.
• Enter 4357 for the PIN code. (PIN code 4357 is always accepted.)
18
How to Care for Your BRAVIA
Safety is very important, please read and follow the safety documentation (Safety Booklet)
separately provided.
Unplug the TV and other connected equipment from the wall
outlet before you begin cleaning your TV.
• Wipe the LCD screen gently with a soft cloth.
• Stubborn stains may be removed with a cloth slightly moistened with a
solution of mild soap and warm water.
• If using a chemically pretreated cloth, please follow the instruction
provided on the package.
• Never use strong solvents such as a thinner, alcohol or benzine for cleaning.
• Do not plug in the TV into the wall outlet until the moisture from cleaning has evaporated.
If you have young children or pets at home, check regularly to insure the TV is securely fastened.
19
Specifications
System
Television system
NTSC: American TV standard
ATSC (8VSB terrestrial): ATSC compliant 8VSB
QAM on cable: ANSI/SCTE 07 2000 (Does not include CableCARD functionality)
Channel coverage
Analog terrestrial: 2 - 69 / Digital terrestrial: 2 - 69
Analog Cable: 1 - 135 / Digital Cable: 1 - 135
Panel system
LCD (Liquid Crystal Display) Panel
10 W + 10 W
Speaker output
Input/Output jacks
CABLE/ANTENNA
VIDEO IN 1/2
75-ohm external terminal for RF inputs
VIDEO / AUDIO
COMPONENT IN 1/2
HDMI IN 1/2/3/4
YPBPR (Component Video) / Signal format: 480i, 480p, 720p, 1080i, 1080p / AUDIO
HDMI: Video: 480i, 480p, 720p, 720/24p, 1080i, 1080p, 1080/24p
HDMI: Audio: Two channel linear PCM 32, 44.1 and 48 kHz, 16, 20 and 24 bits, Dolby Digital
AUDIO (HDMI IN 4)
AUDIO OUT
500 mVrms (typical)
DIGITAL AUDIO OUT
(OPTICAL)
PCM/Dolby Digital optical signal
PC IN
D-sub 15-pin, analog RGB
Stereo mini jack
PC/HDMI 4 AUDIO INPUT
LAN
10BASE-T/100BASE-TX connector (Connection speed may differ depending on the network environment.
10BASE-T/100BASE-TX communication rate and communication quality are not guaranteed for this TV.)*1
USB/DLNA
Refer to the i-Manual for supported format.
3D Sync terminal for optional transmitter
3D SYNC
REMOTE (HX909 series only)
RS232C, D-sub 9 pin.
This jack is for receiving the external control signal.
Model name KDL-/XBR-
55HX800
52HX909
46HX909
46HX800
40HX800
Power and others
Power requirement
Power consumption
in use
110 V - 240 V AC, 50/60 Hz (U.S.A./Canada 120 V AC, 60 Hz)
167 W
201 W
184 W
14 W
149 W
132 W
in DAM*2
(You may hear a clicking noise during the download but this is normal.)
in standby
Less than 0.12 W with 120 V AC and less than 0.2 W with 240 V AC
Screen size
(inches measured diagonally)
54.6 inches
52 inches
46 inches
40 inches
(55 class)
1,920 dots (horizontal) × 1,080 lines (vertical)
Display resolution
Speaker
34 × 160
34 × 100
1 3/8 × 4
34 × 160
1 3/8 × 6 3/8
Full range with speaker (mm)
box (2) (inches)
1 3/8 × 6 3/8
Dimensions withstand (mm)
(inches)
1,278 × 797 × 350 1,263 × 807 × 400 1,124 × 727 × 400 1,085 × 688 × 260
952 × 613 × 250
37 1/2 × 24 1/4 ×
9 7/8
50 3/8 × 31 1/2 ×
13 7/8
49 3/4 × 31 7/8 ×
15 3/4
44 3/8 × 28 5/8 ×
15 3/4
42 3/4 × 27 1/8 ×
10 1/4
withoutstand (mm)
(inches)
1,278 × 765 × 73
50 3/8 × 30 1/8 ×
1,263 × 775 × 67
49 3/4 × 30 5/8 ×
1,124 × 695 × 67
44 3/8 × 27 3/8 ×
1,085 × 656 × 74
952 × 581 × 74
42 3/4 × 25 7/8 × 3 37 1/2 × 22 7/8 × 3
2
7/8
2
3/4
2
3/4
wall-mount hole pattern (mm)
wall-mount screw size (mm)
400 × 300
300 × 300
M6
Mass
with stand (kg)/(lb.)
26.9/59.3
22.6/49.8
42.9/94.5
36.9/81.3
36.2/79.8
30.2/66.6
19.2/42.3
16.9/37.3
16.4/36.2
14.2/31.3
without stand (kg)/(lb.)
Supplied accessories
Optional accessories
Connecting cables / Support Belt Kit / Wall-Mount Bracket / TV Stand / 3D Glasses (TDG-BR100/TDG-
BR50) / 3D Sync Transmitter (TMR-BR100)
*1 For LAN connections, use a Category 7 10BASE-T/100BASE-TX cable (not supplied).
*2 Download Acquisition Mode (DAM) is used for software updates and/or collecting data for TV Guide On Screen.
• Optional accessories availability depends on its stock.
• Design and specifications are subject to change without notice.
20
Compatible Optional Accessories
Information
Use the following Sony optional accessories with
Declaration of Conformity
Trade Name: SONY
Model: KDL-55HX800/XBR-52HX909/XBR-46HX909/
KDL-46HX800/KDL-40HX800
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo,
your TV model.
Sony TV Model No.
55HX800 52HX909 46HX909 46HX800/
40HX800
KDL-/XBR-
San Diego, CA 92127 U.S.A.
Telephone Number: 858-942-2230
Sony Wall-Mount
Bracket Model No.
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
SU-WL500
Sony TV
Stand No.
–
SU-52HX1 SU-46HX1
–
*
* Some of these TV Stand models may not be available in
your area.
Use with other optional accessories may cause instability
and could result in property damages or injury.
For customers in Canada
This Class B digital apparatus complies with Canadian
ICES-003.
For instructions on using the Wall-Mount bracket with your
model and download “Additional Information for Using
Sony Wall-Mount Bracket”.
FCC Related Information
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one
or more of the following measures:
To Customers
Sufficient expertise is required for TV installations. Be
sure to subcontract the installation to a Sony dealer or
licensed contractor and pay adequate attention to safety
during the installation.
❑
❑
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
❑
❑
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
Pursuant to FCC regulations, you are cautioned that any
changes or modifications not expressly approved in this
manual could void your authority to operate this
equipment.
Note
This television includes a QAM demodulator which should
allow you to receive unscrambled digital cable television
programming via subscription service to a cable service
provider. Availability of digital cable television
programming in your area depends on the type of
programming and signal provided by your cable service
provider.
21
For Your Convenience
Be sure to register your TV.
Online
Registration:
United States
Canada
Your TV is capable of receiving software updates. For the
latest information about software updates for your TV, visit:
United States
Canada
Software
Updates:
NOTE: If your TV is connected to the Internet, you can check
for software updates by selecting Settings, Product
Support and then Automatic Software Update.
© 2010 Sony Corporation Printed in U.S.A.
|