Sony Digital Camera CCU TX50 User Manual

3-863-129-11 (1)

Camera Control Unit

Operating Instructions

Before operating the unit, please read this manual thoroughly and retain it for future

reference.

CCU-TX50/50P

Table of Contents

Overview ................................................................. 4

Function and Location of Parts and Controls .... 5

Front panel .......................................................... 5

Rear panel ........................................................... 9

Connecting the CCU-TX50/50P to the Video

Camera ................................................................. 12

Notes on connections ....................................... 12

Self-Diagnostics .................................................... 13

Entering the Self-diagnostics Mode ................. 13

Settings of the Camera ..................................... 13

Status Display of the Unit ................................ 13

Self-diagnostics of the Camera System ............ 14

Results of the Self-diagnosis of the Internal

Boards of the Unit .......................................... 14

Diagnostics Page of the Camera ....................... 16

Exiting the Self-diagnostic Mode ..................... 16

When an Error Occurs ...................................... 16

Notes on Use ......................................................... 17

Specifications ........................................................ 17

General ............................................................. 17

Input signals ..................................................... 17

Output signals ................................................... 17

Camera input/output signals ............................. 18

Supplied accessories ......................................... 18

Optional accessories ......................................... 18

Overview

The CCU-TX50/50P is a camera control unit that

connects to DXC-D50 Series Color Video Cameras via

the CA-TX50/50P Camera Adaptor.

Features of this unit are described below.

Full-featured signal transfer functions

• The CCU-TX50/50P is able to transfer wide band

component video signals.

• The maximum triaxial cable length that can be used to

connect this unit to a camera adaptor is max. 750 m

(when using a Belden φ8.5 mm cable) or 1125 m

(when using a Belden φ13.2 mm cable).

• Transfer functions are provided for the following

signals.

Return video, teleprompter signal, microphone audio,

program audio, red tally and green tally signals

• An intercom system is also provided.

Flexibly adaptable camera control functions

• The camera control panel mounted on the front panel

of the unit enables video camera operations to be

controlled from the unit.

• When the RCP-D50 remote control panel is connected

to the rear panel of the unit, the video camera

operation can be controlled from both the remote

control panel and the front panel of the unit.

Wide array of input/output signals

The input and output connectors provided for the CCU-

TX50/50P include those for outputting such signals as a

composite video signal (VBS), component video signals

(switchable to RGB), SDI signals, and video signals for

video and waveform monitors, for inputting a reference

signal for external synchronization.

Status and self-diagnostics display on the

picture monitor

You can check all sorts of settings of the unit and the

results of self-diagnoses of internal boards on the

monitor connected to the PIX connector on the rear

panel.

Rack mountable

Two CCU-TX50/50P units can be installed side by side

in the optional RMM-301 Rack Mount Bracket.

Overview

Function and Location of Parts and Controls

Front panel

a Camera number sheet/tally indicator

b POWER switch/CAM and MAIN indicators

c CABLE ALARM indicators

d INCOM input/output/setting section

a Camera number sheet/tally indicator

Lights red when the red tally signal is input (e.g. when

Note

the video signal from the video camera connected to the

CCU-TX50/50P goes on air). When the CALL button

on the unit or RCP-D50 remote control panel is pressed,

the indicator lights red if it is not lit, and goes off if it is

lit.

If the fan in the CCU-TX50/50P stops, the MAIN

indicator will flash simultaneously to warn you of the

abnormal condition. If this occurs, turn the POWER

switch off immediately and contact Sony service

personnel.

The indicator lights green when the green tally signal is

input.

c CABLE ALARM indicators

Attach the supplied number sheet here to indicate the

camera number.

OPEN: Lights when no triaxial cable is connected to

the CAMERA connector on the rear panel of the

CCU-TX50/50P, or when the load current is

extremely low even when a camera cable is connected.

SHORT: Lights when there is a current overflow in

the triaxial cable.

b POWER switch/CAM (camera) and MAIN

indicators

The POWER switch turns on or off the power supply to

the entire camera system, including the CCU-TX50/

50P, the video camera, and the remote control unit

connected to the REMOTE connector on the CCU-

TX50/50P.

d INCOM (intercom) input/output/setting section

INCOM (intercom) connector (XLR, 5-pin)

Connects a headset.

The MAIN and CAM indicators light when the POWER

switch is turned on.

INCOM level control

The CAM indicator goes off when the power is turned

off by the CAM PW button on the remote control panel.

Adjusts the input level of the headset.

MIC/PGM (program audio) switch

ON: Turns on the headset microphone.

Function and Location of Parts and Controls

OFF: Turns off the headset microphone.

PGM: Outputs the program audio. When this position

is selected, the INCOM level control adjusts input

level of the program audio.

PROD: Producer line.

PRIV: Producer line and engineer line are cut off and

communication is possible only between the CCU-

TX50/50P and the camera connected to the rear panel

of the CCU-TX50/50P.

INCOM selector

ENG: Engineer line.

Selects the pathway of intercom signals output/input

through the INCOM connector.

e CALL button

f PANEL button

g BARS button

h 5600K button

i AUTO KNEE button

j SKIN DTL button

k TLCS button

l CHARACTER button

m MASTER GAMMA

adjustment knob

n DETAIL adjustment knob

e CALL button

h 5600K button

When you press this button, the TALLY indicator on the

camera adaptor lights. The tally indicator on the unit

also lights red when you press this button, and goes off

if the CALL button is pressed while it is lit.

Press this button (which lights up when pressed) to

convert the color temperature electronically instead of

using the optical filter.

i AUTO KNEE button

f PANEL button

Press this button (which lights up when pressed) to

activate the automatic knee function which optimizes

the input signal compensation.

When the RCP-D50 camera control panel is connected,

press this button to light it up so you can select the

device which controls the camera.

The unit can control the camera when this button is lit.

j SKIN DTL button

Use this button to turn the skin detail correction function

on or off. Press this button (which lights up when

pressed) to set the skin detail correction function to on.

To set this function to off, press this button again.

BARS button

Press this button (which lights up when pressed) to send

the color bar signal to the monitor. The color bars then

appear on the monitor.

k TLCS (total level control system) button

Press this button to turn the total level control system on

or off. When this button is lit, it is turned on, and settings

Function and Location of Parts and Controls

made with the GAIN control section and SHUTTER

setting section are ignored.

changes to the next page. When this button is not lit, the

self-diagnostics screens are not displayed.

l CHARACTER button

m MASTER GAMMA adjustment knob

Use this knob to adjust the gamma curve.

Press this button (which lights up when pressed) to

display the self-diagnostics screen on the picture

monitor. Each time you press this button, the screen

n DETAIL adjustment knob

Use this knob to adjust the detail level.

o SHUTTER setting section

p GAIN control section

q WHITE/BLACK BALANCE setting section

r MASTER BLACK

adjustment knob

s IRIS setting section

o SHUTTER setting section

Selects a shutter setting.

Display

Displays the clear scan frequency when the CLS button

lights, or the shutter speed when the ON button lights.

Note

p GAIN control section

Adjusts the gain to obtain the most appropriate level for

the lighting condition.

UP/DOWN selector

The gain is increased, each time you press this selector

to the UP position. The gain is decreased, each time you

press this selector to the DOWN position.

Display

This section does not function when the TLCS button is

on.

CLS button

Press this button (which lights up when pressed) to

activate the clear scan function.

ON button

Press this button (which lights up when pressed) to

activate the normal shutter function.

UP/DOWN selector

Displays the gain values in decibel units.

When the CLS button lights: The clear scan frequency

is increased, each time you press this selector to the UP

position. The clear scan frequency is reduced, each time

you press this selector to the DOWN position.

When the ON button lights: The shutter speed is

increased, each time this selector to the UP position. The

shutter speed is reduced, each time you press this

selector to the DOWN position.

Function and Location of Parts and Controls

q WHITE/BLACK BALANCE setting section

r MASTER BLACK adjustment knob

Adjusts the master black levels of the R, G, and B

signals simultaneously. The click position of the knob

provides a typical setting.

A WHITE controls

B PRESET button

s IRIS setting section

A EXT indicator

B AUTO button

C BLACK controls

D AUTO WHITE/BLACK switch

E ATW button

C IRIS control

A WHITE (white balance manual adjustment)

controls

Turn these controls to manually adjust the white

balance. The left-hand control adjusts the R signal level

and the right-hand control adjusts the B signal level.

A EXT (extender) indicator

Lights when a lens extender is being used on the video

camera.

B AUTO button

Press this button (which lights up when pressed) for

automatic adjustment of the iris. This button lights when

the automatic adjustment is in progress. Press this button

again to manually adjust the iris.

B PRESET button

Press this button (which lights up when pressed) to set

the white balance to the preset value. When this button

is lit, the operation of the AUTO WHITE section of the

AUTO WHITE/BLACK switch is ignored.

C IRIS control

Adjusts the iris manually when the AUTO button is set

to off. When the AUTO button lights, you can turn this

control to change the reference value for the automatic

iris adjustment.

C BLACK (black balance manual adjustment)

controls

Turn these controls to manually adjust the black balance.

The left-hand control adjusts the R signal level and the

right-hand control adjusts the B signal level.

D AUTO WHITE/BLACK (white balance/black

balance automatic adjustment) switch

Activates the automatic adjustment of the white balance

and black balance.

WHITE: Adjusts the white balance automatically one

time when the switch is set to this position.

BLACK: Adjusts the black balance automatically one

time when the switch is set to this position.

E ATW (auto tracing white balance) button

Press this button (which lights up when pressed) to have

the white balance adjusted automatically when lighting

conditions change.

Function and Location of Parts and Controls

Rear panel

a CAMERA connector

b AUDIO OUTPUT connectors

c INPUT connectors

d OUTPUT connectors

e REMOTE connector

i AC IN connector

h WF MODE connector

g MIC REMOTE connector

f INTERCOM/TALLY/PGM connector

a CAMERA connector (triaxial connector)

Connects to the CA-TX50/50P Camera Adaptor

attached to the DXC-D50 Color Video Camera using a

triaxial cable.

connector is terminated automatically with an

impedance of 75 ohms.

A REFERENCE INPUT connectors

Caution

Do NOT use a defective triaxial cable.

The inner sheath of a triaxial cable is used for power

supply and the outer sheath for safety ground.

For your safety, do NOT use a triaxial cable whose inner

and outer sheaths are short-circuited. Use of such a cable

will cause electric shock.

B RET-1/RET-2 connectors

b AUDIO OUTPUT connectors (XLR, 3-pin)

Supply audio signals from the video camera.

C RET-3/PROMPTER connectors

c INPUT connectors

D COAX connector

The two connectors of each pair are loop-through

connectors. When the upper connector is used and no

connection is made to the lower connector, the upper

Function and Location of Parts and Controls

A REFERENCE INPUT connectors (BNC type)

Accept reference signals (black burst signal) for external

synchronization.

B Y/G, R-Y/R, B-Y/B (component video signal /

RGB output) connectors (BNC type)

Supply the component signals or the R, G, and B signals

for the chroma keyer from each connector.

Use the switch on the internal board to select the signals

to be output.

B RET-1/RET-2 (return video signal 1/2)

connectors (BNC type)

Accept return video signals from two different systems.

For details on the internal boards, consult your nearest Sony

dealer.

For details on the selection of RET-1 and RET-2, refer to

Operation Manual that came with the camera or camera

adaptor.

C PIX (picture monitor output) connector (BNC

type)

Supplies a video signal or video and character signals

C RET-3/PROMPTER (return video signal 3/

prompter) connectors (BNC type)

Accept a return video signal or a teleprompter signal.

together to a picture monitor.

When using the RCP-D50 Remote Control Panel, you

can select the signal output from the PIX connector

using the MONITOR SELECT button on the menu of

the RCP-D50. When the signal output from the PIX

connector changes, the waveform output on the

waveform monitor also changes.

For details on the selection of RET-3, refer to Operation

Manual that came with the camera or camera adaptor.

To set this connector to the PROMPTER output, it is

required to change the setting in the internal board.

D SYNC connector

Connect to the synchronous signal input connector on a

For details on the internal boards, consult your nearest Sony

dealer.

waveform monitor or picture monitor

D COAX (coaxial) connector (BNC type)

Accepts and supplies signals from/to the video camera

using a coaxial cable. Power is not supplied to the

camera and a camera adapter through this connector.

E WF (waveform monitor output) connector (BNC

type)

Supplies a video signal to a waveform monitor.

When using the RCP-D50 Remote Control Panel, you

can select the signal output from the PIX connector

using the MONITOR SELECT button on the menu of

the RCP-D50. Changing the signal output from the WF

connector simultaneously changes the picture on the

picture monitor.

To use this connector, it is required to change the setting of the

internal board. For details, consult your nearest Sony dealer.

d OUTPUT connectors

A VBS/SDI-1/VBS/SDI-2/VBS/SDI-3

e REMOTE (RCP (remote control panel) remote)

connector (10-pin)

connectors

Connects to the RCP-D50 Series Remote Control Panel

with an optional CCA-7 connecting cable to transmit/

receive control signals.

B Y/G, R-Y/R, B-Y/B connectors

f INTERCOM/TALLY/PGM (program audio)

connector (D-sub, 25-pin)

C PIX connector

Inputs/outputs intercom, tally, or program audio signals.

Connects to an intercom, tally, or program audio

connector of an intercom system.

D SYNC connector

E WF connector

g MIC REMOTE (microphone remote control)

connector (D-sub, 15-pin)

Connects to an external control unit such as an audio

mixer. With the connected unit, you can set the

microphone input level of the video camera to –60, –50,

–40, –30, or –20 dB.

A VBS/SDI-1/VBS/SDI-2/VBS/SDI-3 (composite

video signal 1/2/3 output) connectors (BNC type)

Supply the signal from the video camera in composite or

SDI format.

Use the switch on the internal board to select the signals

to be output.

h WF MODE (waveform monitor mode)

connector (4-pin)

Connects to the corresponding connector on a waveform

For details on the internal boards, consult your nearest Sony

dealer.

monitor to allow the sequential monitoring of signals.

Function and Location of Parts and Controls

i AC IN (AC power input) connector

Connects to an AC power source using the supplied AC

power cord. Secure the power cord to the CCU-TX50/

50P using the supplied plug holder.

Function and Location of Parts and Controls

Connecting the CCU-TX50/50P to the Video Camera

When connecting a CCU-TX50/50P to a DXC-D50

Color Video Camera, you must first attach the CA-

TX50/50P Camera Adaptor to the video camera.

CA-TX50

Triaxial cable

DXC-D50

CCU-TX50/50P

To an AC power source

Notes on connections

Triaxial cable

The triaxial cable should never be connected to or

disconnected from the CCU-TX50/50P when the power

is turned on. Always turn the unit off first.

Video camera

Some switches or controls on the video camera may not

work when the camera is connected to the CCU-TX50/

50P.

For details, refer to Operation Manuals of the video camera

and the camera adaptor.

Connecting the CCU-TX50/50P to the Video Camera

Settings of the Camera

The settings and operations status of the camera are

displayed.

Self-Diagnostics

The unit allows you to display the status of the unit and

the results of a self-diagnosis is of the internal boards of

the unit on the screen of a picture monitor connected to

the unit.

You can display the following status items:

• Settings of the camera

• Status display of the unit

• Results of a self-diagnosis of the internal boards

• Self-diagnostics of the camera system

Setting change and adjustment

progress message display area

Entering the Self-diagnostics Mode

The unit enters the self-diagnostics mode, by pressing

the CHARACTER button on the front panel of the unit.

Each time you press the CHARACTER button, the

display changes.

CHARACTER button

1 Master gain

2 “4:3” is displayed when the images recorded in 16:9

format are output after converted to the images of

the 4:3 mode.

3 “EVS” is displayed when EVS of the electrical

shutter is on.

4 Shows the shutter speed currently selected.

5 Shows the on/off setting of the shutter.

6 Shows the type of ND filter currently selected.

7 Shows the F-stop (iris setting) of the lens.

8 EX is displayed when a lens extender is used.

Status Display of the Unit

Press the CHARACTER button when the screen of the

camera settings is displayed. The status of the unit is

displayed.

DXC-D50: Model name and format of the connected

camera

Self-Diagnostics

CCU-TX50: Model name and format of the camera

control unit connected.

Page 2

Genlock: External reference signal and its status

(lock/unlock)

Prompter: Transmission direction of the prompter

line

Return 1 to 3: Return video signal input status

Self-diagnostics of the Camera

System

Press the CHARACTER button when the status display

of the unit is displayed. Page 1 of the self-diagnostics

display is displayed.

The results of a self-diagnosis of the camera system are

displayed spread over three pages.

CAMERA cable: Camera cable connection status

(connected/shorted)

CAMERA Data: Camera data transmission status

CAMERA Power: Status of the power supply to a

camera

Page 1

CAMERA Tone: Camera ID tone status

RCP cable: Connection status of the REMOTE

connector

RCP Data: Data transmission status of the REMOTE

connector

RCP Power: REMOTE connector power supply

status

Page 3

TRIAX TYPE: Type of Triaxial circuit

TRIAX Cable: Triaxial cable connection status

(connected/disconnected)

TRIAX Comp.: Cable compensation type selected

for the triaxial cable (automatic/manual)

TRIAX Step: Compensation step of the triaxial cable

(step indication in the circuit) (The cable length may

not be displayed correctly.)

Fan power: Fan status in the CCU power block

Timer: Power up time to devices connected

CCU Power: Status of the CCU power supply

Intercom CCU: CCU intercom selection (system/

private)

Intercom CAMERA CH1: Status of intercom 1 of a

camera (producer line/engineer line)

CHU MIC Gain: Gain and control status of the

microphone circuit

Results of the Self-diagnosis of the

Internal Boards of the Unit

Press the CHARACTER button when page 3 is

displayed. Page 1 of the results of the self-diagnosis of

the internal boards is displayed.

Self-Diagnostics

Each time you press the CHARACTER button, another

page of results is displayed in turn.

AT board

DM board

Reference: Operation mode of the phase adjustment

Gen Lock: Locking status

BATT Volt: Voltage of the coin battery supplied with

the AT board

CCU Mode: Operation mode of the CCU

PLD Config.: Configuration result status of the PLD

mounted on the AT board

CAM Video: Reception status of the video signals

from the camera.

Skin Gate: Reception status of the Skin gate signal

from the camera

TRIAX Comp.: Cable compensation type selected

for the triaxial cable (automatic/manual)

TRIAX Step: Compensation step of the triaxial cable

(step indication in the circuit) (The cable length may

not be displayed correctly.)

CCU Power: CCU power supply type (AC/DC) and

power supply status

AU board

Power: DM board power supply status

TR board

CAMERA MIC: Input status of the camera

microphone (on/off)

CAMERA LINE: Pathway of the intercom signal of

the camera (ENG/PROD/PRIV)

CCU FRONT MIC: Input status of the unit’s

microphone (on/off)

Prompter: Setting status of the prompter line

Tone: Tone signal status

Incom: Demodulating status of the intercom line

CHU Data: Data reception status from the camera

Power: Power supply status of the TR board

CCU FRONT LINE: Pathway of the connection of

the intercom signal of the unit (ENG/PROD/PRIV)

POWER: Power supply status of the AU board

Self-Diagnostics

IV board

Diagnostics Page of the Camera

Return: Setting status of the return signal input

connectors to the return channels from 1 to 3

Return Signal: Status of the return video input signal

Rear CN: Power supply status of the CN board on the

rear

PLD Config: Configuration completion status of the

PLD mounted on the IV board

Power: Power supply status of the IV board

The results of the diagnosis of each board of the camera

are displayed.

Exiting the Self-diagnostic Mode

Display the last “ROM Version” page, and then press the

CHARACTER button again.

EN board

When an Error Occurs

The error message is displayed on the picture monitor. In

such a case, display the self-diagnostics page

corresponding to the board where the error has occurred

by pressing the CHARACTER button.

Component: Setting status of the component output

signal from the OUTPUT connector and status of the

sync signal added to the component Y/G output signal

from the OUTPUT connector

Composite Out-1: Signal type from composite output

connector 1 (VBS/SDI)

Composite Out-2: Signal type from composite output

connector 2 (VBS/SDI)

Composite Out-3: Signal type from composite output

connector 3 (VBS/SDI)

Composite Setup: Setup settings to be added to the

VBS signal

Rear VDA: Power supply status of the VDA board on

the rear

PLD Cofig: Configuration completion status of the

PLD mounted on the EN board

Power: Power supply status of the EN board

Self-Diagnostics

Notes on Use

Specifications

Use and storage locations

General

Power consumption

100 - 240 V AC, 50/60 Hz,

maximum 1.3 A

Peak inrush current

Avoid using or storing the unit in the following places:

• Where it is subject to extremes of temperature

(operating temperature: +5ºC to +40ºC (41ºF to

104ºF)).

Note that in summer the temperature in a car with the

windows closed can reach 50ºC (122ºF).

• Very damp or dusty places.

(1) Power ON, current probe method:

50 A (240V)

(2) Hot switching inrush current,

measured in accordance with

European standard EN55103-1:

10 A (230V)

• Where rain is likely to reach the unit.

• Places subject to severe vibration.

• Near strong magnetic fields

Cable length

Operating temperature

Maximum 750 m (φ 8.5 mm)

Near transmitting stations generating

strong radio waves.

+5ºC to +40ºC (41ºF to 104ºF)

Dimensions

Mass

200 × 124 × 365 mm

Avoid violent impacts

Dropping the unit, or otherwise imparting a violent

shock to it, is likely to cause it to malfunction.

(8 × 5 × 13 7/8 in.) (w / h / d)

not including projecting parts

Approx. 5.5 kg

Do not cover with cloth

While the unit is in operation, do not cover it with a cloth

or other material. This can cause the temperature to rise,

leading to a malfunction.

Input signals

REFERENCE BNC type (loop-through)

VBS/BS, 1.0 Vp-p, 75 ohms automatic

terminated

RET-1/2/3

BNC type (1 each, loop-through)

VBS, 1.0 Vp-p, 75 ohms automatic

terminated

BNC type (loop-through)

VBS, 1.0 Vp-p, 75 ohms

After use

Turn the POWER switches on the unit and camera

control unit off.

PROMPTER

Care

1) The same signal is input to RET-3 and PROMPTER.

If the body of the unit is dirty, wipe it with a dry cloth.

For severe dirt, use a soft cloth steeped in a small amount

of neutral detergent, then wipe dry. Do not use volatile

solvents such as alcohol or thinners, as these may

damage the finish.

Output signals

VBS 1/2/3

BNC type (1 each)

VBS, 1.0 Vp-p, 75 ohms

BNC type (3)

SDI

SDI format, 270 Mbps, SMPTE 259M

(CCU-TX50)/CCIR656-III (CCU-

TX50P)

Y/R-Y/B-Y video

BNC type (1 each)

Y: 1.0 Vp-p, 75 ohms

R-Y/B-Y: U.S.A. and Canada:

700 mVp-p, 75 ohms

Europe: 525 mVp-p, 75 ohms

BNC type (1 each)

R/G/B video

700 mVp-p, 75 ohms

BNC type (1)

PIX

1.0 Vp-p, 75 ohms

BNC type (1)

NTSC: 714 mVp-p, 75 ohms

Notes on Use / Specifications

PAL: 700 mVp-p, 75 ohms

Encoded output: 1.0 Vp-p, 75 ohms

4-pin (1)

WF MODE

AUDIO OUTPUT

XLR, 3-pin

0 dBu/–20 dBu, balanced, 2 channels

BNC type

SYNC

2) R/G/B/and Y/R-Y/B-Y are switchable.

Camera input/output signals

CAMERA

Triax (Kings type for the U.S.A.

and Canada, Fischer type for Europe)

BNC type (1), 75 ohms

COAX

REMOTE

10-pin, multi connector

INTERCOM/TALLY/PGM

D-sub, 25-pin (1)

4W/RTS

TALLY: 24 V DC, TTL level or

contact selectable

MIC REMOTE D-sub, 15-pin (1)

INCOM (on the front panel)

XLR, 5-pin (1)

Supplied accessories

AC power cord (1)

AC power plug holder (1)

Number plate (1 set)

Operating Instructions (1)

CD-ROM (including multi-lingual operating

instructions) (1)

Warranty booklet (1)

Optional accessories

Remote Control Panel RCP-D50

Rack Mount Bracket RMM-301

Design and specifications are subject to change without

notice.

Specifications

Sony Corporation

Sigma MP3 Player MAX P 01 User Manual
Sony PDAs Smartphones PEG NX73V User Manual
Sony VCR DSR 30 User Manual
Sony Video Game Headset MDR RF920RK User Manual
SoundMax Car Stereo System SM CDM1057 User Manual
Sunbeam Iron 121998 User Manual
Superior Indoor Fireplace VF4000 CHN 2 User Manual
Sylvania DVD Player 6724DG User Manual
Sylvania Stereo Amplifier 6900DTE User Manual
Tapco DJ Equipment MIX10FXP User Manual