Sonic Alert Door DB200 User Manual

SIGNALER  
DB SENSOR  
INSTALLATION  
To install the DB200, follow the diagrams and instructions on  
the following page that match the type of installation you  
need for your home. If the installation follows diagrams 1-4,  
a 9 volt alkaline battery is required in the DB sensor.  
WIRELESS DOORBELL & TELEPHONE  
SIGNALER  
MODEL DB200  
Please check the switches on your DB200 Sensor before  
installing. Do not change switches 1-6 these are pre set.  
It’s very important that the switch settings on both units  
match . See figure 1.1 on back side for settings.  
SONIC ALERT’S 5 YEAR LIMITED WARRANTY  
DB Sensor settings, smaller unit: 1 thru 6 dip switches are  
set at the factory and only need to be changed if your  
neighbor has a DB200 or DB100. The 8 dip switches should  
be set as follows:  
The Wireless Doorbell Signaler Model DB200 is  
warranted against manufacturing defects in materials  
and workmanship for two (5) years from the date of  
purchase. Within this period Sonic Alert will repair or  
replace at our option the DB200 without charge for parts  
and labor. Simply send the DB200 (postpaid) and a  
copy of your sales slip as proof of purchase to:  
a)  
1 thru 3 dip switches are set in the ON position and  
4 thru 6 are set in the OFF position. If you need to  
change the dip switch settings to avoid interference  
with your neighbors make sure you change both the  
DB200 Signaler to match the DB Sensor.  
Sonic Alert Inc., 1050 E. Maple Road, Troy MI 48083  
b)  
The 8th switch determines the number of flashes  
when someone is at your door. In the ON position  
your until will flash 5 times and in the OFF position  
your unit will flash 10 times. This feature is  
wonderful when you have an extra sensor for the  
back door. One sensor would be set in the ON  
position and the other would be set in the OFF  
position.  
OPERATION  
The state-of-the-art, Doorbell Signaler will alert you when  
someone comes to visit. The Doorbell Signaler, Model DB200 is  
the only doorbell and intercom signaler that requires no wires and  
can be installed in seconds. DB200 will alert you that someone is  
at your door by flashing a light plugged into the base unit or any  
Sonic Alert receiver anywhere in your home.  
The DB200 is designed to work with homes with or without an  
existing doorbell or chime and all existing buzzer and intercom  
systems.  
c)  
The 7th switch is for use when using 2 sensors, this  
switch determines the settings for front or back door.  
If using for one door only set this switch in the ON  
position. At this setting your unit will flash at a fast  
rate and will make a ding/dong sound. If using 2  
sensors one for the front door and one for the back  
door the setting for the 2nd sensor would be in the  
OFF position. In this position the front door will  
flash at a different flash rate than the back door. In  
the OFF position your back door sensor will flash at  
a slow rate with a dong/dong sound.  
Other features include selectable number of flashes (5 or 10),  
different flash code for front door, rear door, or intercom.  
Additional sensors sold separately for 2nd door or source. There is  
also a built-in chime for hearing members of the family (can be  
turned off by using the switch on the right side of the DB200).  
The DB200 receives an RF radio signal from the DB200 sensor,  
and flashes the light plugged into the built-in outlet of the DB200.  
Use a 300 watt or less incandescent lamp only. The DB200 can  
send a signal to all Sonic Alert remote receivers. Note: Must be  
used only with Sonic Alert receivers for proper operation,  
other manufacturers products are not reliable with our  
products.  
Function settings:  
The function switch on the back of DB sensor (smaller unit)  
should be set depending on which installation application you  
need. See diagram on back.  
Switch position:  
Top - Intercom/ Buzzer System/ Wireless Chime Box  
Installation see (3 &4).  
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.  
Operation is subject to the following two conditions:  
(1)This device may not cause harmful interference, and  
Center - Outside Doorbell Button Only see (1 & 2)  
(2)this device must accept any interference received, including interference that may cause  
undesired operation.  
Bottom - Hard Wired to Existing Doorbell chime Box  
Installation see (5).  
WARNING: Changes or modifications not expressively approved by the party  
responsible for compliance could void user’s authority to operate the equipment.  
 

Sennheiser Headphones Wireless RS 60 User Manual
Smooth Fitness Treadmill 825E User Manual
Snapper Blower SLB8621C User Manual
Sony Car Stereo System Model TC SP55 User Manual
Sony Ericsson Cell Phone P908 User Manual
Sony Microcassette Recorder ICD B310F User Manual
Sony Portable CD Player MDX CA580 User Manual
SOYO Computer Hardware SY 6ZB User Manual
Spalding Fitness Equipment M8660411 User Manual
Sub Zero Freezer 601F User Manual