SE112 Sound Isolating™ Earphones
Choosing a Sleeve
Cleaning the Nozzle
Soft flex sleeves are included in small, medium, and large sizes.
Select an earphone sleeve that provides the best fit and sound
isolation. It should be easy to insert, fit comfortably, and easy
to remove.
If you notice a change in sound quality, remove the sleeve and
check the nozzle of your earphone. If nozzle is blocked, clear
obstruction by using wire loop end of cleaning tool.
Wearing the Earphones
The following are some suggested ways of wearing the
earphones.
Nozzle
Soft Flex Sleeves
Nozzle Cleaning Tool
Warning: The cleaning tool is only to be used to clean the
earphones. Any other use, such as using the tool to clean ears,
could result in injury.
Over the ear
Using the Remote (m+
models only)
Inserting the Earphones
Maintenance and Cleaning
Careful maintenance ensures a tight seal between the sleeve
and nozzle, improving sound quality and product safety.
Use the remote to control compatible media phone players.
Insert the earphones so they form a tight seal. The fit of the ear-
phone can greatly affect sound quality.
•
Keep the earphones and sleeves as clean and dry as
possible.
Play music
Click the center button once
Click the center button once.
•
To clean sleeves, remove them from earphones, gently rinse
in warm water and air dry. Foam sleeves require a longer
drying time. Inspect for damage and replace if necessary.
Ear sleeves must be completely dry before reusing.
Pause music
Change volume Click the volume up (+) or volume down (-)
button to increase or decrease the volume.
•
Wipe the earphones and sleeves with mild antiseptic to avoid
infections. Do not use alcohol-based disinfectants.
Go to next
track
Double-click the center button.
Triple-click the center button.
Triple-click after 6 seconds.
Important: If there seems to be a lack of low frequency
response (bass), this means that the earphone sleeve is not
forming a tight seal. Gently push the earphone deeper into the
ear canal or try a different sleeve.
•
•
•
Do not expose earphones to extreme temperatures.
Replace sleeves if they do not fit properly.
Go to previous
track
Do not attempt to modify this product. Doing so will void the
warranty and could result in personal injury and/or product
failure.
Restart current
track
Warning: Do not push the earphone sleeve beyond the ear
canal opening.
Fast-forward
Double-click and hold the center button.
Click the center button once.
Send/End Call
Accessories
For more information about compatible models go to: www.
shure.com
Removing the Earphones
For information about earphone accessories and other Shure
products visit:
Grasp the body of earphone and gently twist to remove.
“Made for iPod,” “Made for iPhone,” and “Made for iPad”
mean that an electronic accessory has been designed to
connect specifically to iPod, iPhone, or iPad, respectively,
and has been certified by the developer to meet Apple per-
formance standards. Apple is not responsible for the oper-
ation of this device or its compliance with safety and regu-
latory standards. Please note that the use of this accessory
with iPod, iPhone, or iPad may affect wireless performance.
Furnished accessories subject to change.
Certifications
iPad, iPhone, iPod, iPod classic, iPod nano, iPod touch, and
Retina are trademarks of Apple Inc., registered in the U.S. and oth-
er countries. iPad Air and iPad mini are trademarks of Apple Inc.
The trademark “iPhone” is used with a license from Aiphone K.K.
This product meets the Essential Requirements of all relevant
European directives and is eligible for CE marking.
Note: Do not pull on cable to remove earphone.
The CE Declaration of Conformity can be obtained from: www.
shure.com/europe/compliance
Changing Sleeves
Authorized European representative:
Shure Europe GmbH
•
•
Twist and pull to remove the sleeve from the nozzle.
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: 49-7262-92 49 0
Slide on a new sleeve so that it completely covers the barb
and the nozzle.
Fax: 49-7262-92 49 11 4
Email: [email protected]
Caution: If the barb or any of the nozzle is exposed, the
sleeve is not properly installed. Replace sleeves if they do not
tightly grip the nozzle. To ensure proper fit and performance, use
only sleeves supplied by Shure (unless using custom molded
sleeves).
©2014 Shure Incorporated
27A25176 (Rev. 3)
|