Sharp Microwave Oven TINSKB147MRR1 User Manual

Microwave Drawer®  
InstallatIon Manual  
SPECIAL WARNING  
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.  
IMPORTANT: SAVE ThIS INSTALLATION MANUAL FOR LOCAL ELECTRICAL INSPECTOR’S USE.  
READ AND SAVE ThESE INSTRUCTIONS FOR FUTURE REFERENCE.  
CLEARANCES ANd dImENSIoNS  
For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accord with the stated  
clearances and dimensions on pages 2 and 3. See Figure 1 (for 24") or Figures 3 and 4 (for 30") .  
ImPoRtANt NotES to thE CoNSUmER  
UNPACkING yoUR mICRoWAvE dRAWER  
Keep this manual with your Operation Manual for future  
reference.  
Remove all packing  
materials from inside  
theMicrowaveDrawer.  
DO NOT REMOVE  
THE WAVEGUIDE  
COVER, which is  
located on the top  
of the Microwave  
Drawer.  
Sealing  
surface  
• As when using any microwave oven generating heat, there are  
certain safety precautions you should follow. These are listed  
in the Operation Manual. Read all and follow carefully.  
Waveguide  
cover  
• Be sure your Microwave Drawer is installed and grounded  
properly by a qualified installer or service technician.  
ImPoRtANt SAfEty INStRUCtIoNS  
If the information in this manual is not followed  
exactly, a fire or electrical shock may result that could cause  
property damage, personal injury or death.  
Sealing  
surface  
Remove the feature  
sticker, if there is one.  
Check the drawer for  
any damage, such as  
misaligned or bent  
Oven  
cavity  
To reduce the risk of tipping, the Microwave  
Drawer must be secured by a properly installed Anti-Tip  
block.  
drawer, damaged drawer seals and sealing surfaces, broken  
or loose Microwave Drawer guides and dents inside the cavity  
or on the front side of the drawer. If there is any damage, do  
not operate the Microwave Drawer and contact your dealer or  
a SHARP AUTHORIZED SERVICER.  
• This Microwave Drawer must be electrically grounded in  
accordance with local codes.  
• Make sure the wall coverings and the cabinets around the  
Microwave Drawer can withstand the heat generated by the  
Microwave Drawer.  
ImPoRtANt NotES to thE INStALLER  
Read all of the Installation Manual before installing the  
Microwave Drawer.  
Never leave children alone or unattended in  
the area where a Microwave Drawer is in use. Never leave the  
drawer open when the microwave is unattended.  
Remove all packing material before connecting the electrical  
supply.  
Stepping, leaning or sitting on the drawer  
may result in serious injuries and can also cause damage to the  
Microwave Drawer.  
Observe all governing codes and ordinances.  
Be sure to leave these instructions with the consumer.  
Do not use the Microwave Drawer as a storage space.  
This creates a potentially hazardous situation.  
• Check that the time-of-day is in the display. If not, touch  
Stop/Clear to prevent unintended use.  
TINSKB147MRR1  
E 1  
 
30" mICRoWAvE dRAWER mEASUREmENtS  
Figures 3, 4 and 5 contain many Microwave Drawer measurements  
for reference when planning the drawer’s location.  
A. 6" (152.40 mm)  
C
A
B
B. Suggested electrical  
outlet location*  
E
D
This Microwave Drawer can be installed below any electric or  
gas wall oven.  
C. Anti-Tip block  
D. 5" (127 mm)  
F
G
K
H
* Can also be installed using an electrical outlet in an adjacent  
cabinet within the area where the provided electrical cord can  
reach. Power cord access hole in cabinet should be a minimum  
E. 3-1/2" (88.90 mm)  
F. 4" (101.60 mm)  
I
Q
J
I
G. 28-7/16" (722.31 mm)  
opening  
N
L
1 1/2" diameter hole and deburred of all sharp edges.  
H. 14-13/16" (376.24 mm)  
to bottom of Anti-Tip  
block  
IMPORTANT  
Always allow sufficient power cord length to the  
M
electrical outlet to prevent tension.  
O
Always check electrical codes for requirements.  
I. Allow 3/4" (19.05 mm)  
overlap  
A. 84" (2133.6 mm) wall  
cabinet  
P
J. 23-1/2" (596.9 mm)  
minimum depth  
B. Optional wall oven  
cutout illustrated in  
sketch  
Figure 4  
K. Allow 3/16" (4.76 mm) overlap  
L. 36" (914.4 mm) countertop height  
M.Allow 7/16" (11.09 mm) overlap  
N. Floor must support 100 lb (45.4 kg)  
C. Suggested electrical  
outlet location*  
D. 6" (152.40 mm)  
E. Anti-Tip block  
A
O. 19" (482.6 mm) to top of floor (recommended)  
P. 30" (762 mm) cabinet minimum  
F. 3-1/2" (88.90 mm)  
G. 5" (127 mm)  
B
Q. 14-13/16" (376.24 mm) opening  
H. 4" (101.60 mm)  
I. 2" (50.8 mm) minimum  
E
D
C
J. 28-7/16" (722.3 mm)  
opening  
F
L
A
C
G
B
J
K. Allow 3/16" (4.76 mm)  
overlap  
I
A. 21-5/8"  
(549.28 mm)  
B. 4-11/16"  
(119.06 mm)  
C. 1-3/4"  
(44.45 mm)  
D. 21-7/8"  
(555.63 mm)  
H
J
K
G
F
L. 14-13/16" (376.24 mm)  
to bottom of Anti-Tip  
block  
O
M
N
M
I
Q
M.Allow 3/4" (19.05 mm)  
overlap  
P
D
N. 23-1/2" (596.9 mm)  
minimum depth  
H
R
E
E. 30" (762 mm)  
F. 15" (381 mm)  
O. 14-13/16" (376.24 mm)  
opening  
Figure 5  
S
P. Allow 7/16" (11.11 mm)  
overlap  
G. 14-19/32" (370.68 mm)  
Figure 3  
H. 1-11/16" (42.86 mm) door thickness  
I. 15" (381 mm) auto drawer opening  
J. 4" (101.6 mm)  
Q. Floor must support 100 lb (45.4 kg)  
R. 19" (482.6 mm) to top of floor (recommended)  
S. 30" (762 mm) cabinet minimum  
ANtI-tIP BLoCk  
NORMAL INSTALLATION STEPS  
Anti-Tip block must also be moved  
Anti-Tip block  
6"  
and installed. When installed to  
the wall, make sure that the screws  
completely penetrate the dry wall  
and are secured in wood or metal  
so that the block is totally stable.  
When fastening, be sure that the  
screws do not penetrate electrical  
wiring or plumbing.  
(152.4 mm)  
ANTI-TIP BLOCK INSTALLATION INSTRuCTIONS  
To reduce the risk of tipping of the drawer, the Anti-Tip block must  
be properly installed located 14 13/16-inches above the floor on  
which the Microwave Drawer will sit. The 6-inch Anti-Tip block  
must be provided by the installer. See Figures 1 and 6 (for 24") or  
Figures 3, 4 and 6 (for 30"). The Anti-Tip block prevents serious  
injury that might result from spilled hot liquids.  
3 1/2"  
(89 mm)  
Figure 6  
If the Microwave Drawer is ever moved to a different location, the  
E 3  
 
ELECtRICAL oUtLEt  
dRAWER INStALLAtIoN  
Suggested electrical  
outlet location*  
5" (127 mm)  
Mounting  
flange  
4"  
(101.6 mm)  
Figure 8A  
Parts supplied  
Figure 7  
1. Place the drawer adjacent to the wall or  
cabinet opening. Plug the power supply cord  
into the electrical outlet.  
The electrical requirements are a 120 volt 60 Hz, AC only,  
15 amp. or more protected electrical supply. It is recommended  
that a separate circuit serving only this appliance be provided.  
2. Carefully guide the drawer into the prepared  
opening. Avoid pinching the cord between  
the oven and the wall.  
4 Screws  
The drawer is equipped with a 3-prong grounding plug. It must  
be plugged into a wall receptacle that is properly installed and  
grounded. Should you only have a 2-prong outlet, have a qualified  
electrician install a correct wall receptacle.  
Figure 8B  
3. Slide the drawer all the way until the  
mounting flange is flush with the face of the cabinet. See  
Figure 8A.  
Note: If you have any questions about the grounding or electrical  
instructions, consult a qualified electrician or service person.  
4. Open the drawer. Using the 4 holes on the drawer as a template,  
pre drill the cabinet using a 1/16" bit. See Figure 8A.  
* Can also be installed using an electrical outlet in an adjacent cabinet  
within the area where the provided electrical cord can reach.  
5. Secure the drawer with the 4 screws supplied. See Figure 8B.  
Always check electrical codes for requirements.  
modEL ANd SERIAL NUmBER LoCAtIoN  
GRoUNdING INStRUCtIoNS  
The name plate includes model and serial number. Open the  
Microwave Drawer fully. The label is beyond the back wall of  
the microwave cavity facing up from the flat surface.  
This appliance must be grounded. The Microwave Drawer is  
equipped with a cord having a grounding wire with a grounding  
plug. It must be plugged into a wall receptacle that is properly  
installed and grounded in accordance with the National  
Electrical Code and local codes  
CARE, CLEANING ANd mAINtENANCE  
Refer to the Operation Manual for cleaning instructions.  
and ordinances. In the event of  
3-Prong plug  
an electrical short circuit,  
grounding reduces risk of  
electric shock by providing an  
escape wire for the electric  
current.  
BEfoRE yoU CALL foR SERvICE  
Read the BEFORE YOU CALL and operating instruction sections  
in your Operation Manual. It may save you time and expense.  
The list includes common occurrences that are not the result of  
defective workmanship or materials in this appliance.  
Grounding pin  
– Improper use  
of the grounding plug can result  
in a risk of electric shock. Do  
not use an extension cord. If  
3-Prong receptacle  
Grounded receptacle box  
Refer to the warranty in your Operation Manual for Sharp’s  
service number and address. Please call or write if you have  
inquiries about your microwave product and/or need to order  
parts.  
the power supply cord is too short, have a qualified electrician  
or serviceman install an outlet near the appliance.  
SHARP ELECTRONICS OF CANADA LTD  
335 Britannia Road East • Mississauga, Ontario • L4Z 1W9  
E 4  
 

Sharp Flat Panel Television LC 13AV4U User Manual
Sherbourn Technologies Stereo Amplifier PT 7010A User Manual
Snapper Cultivator 1690715 User Manual
Sony Battery Charger BCR NWS700 User Manual
Sony Stereo System CMT C5 User Manual
Spirit CD Player PLAYER User Manual
Summer Infant Baby Accessories 4524 User Manual
Summit Gas Grill E S 620 650 User Manual
Tanita Scale BC 531 User Manual
Tanita Scale BC 541 User Manual