PN-E471
PN-E421
LCD MONITOR
MONITEUR LCD
MONITOR LCD
LCD FARBMONITOR
ЖК МОНИТОР
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE INSTRUCCIONES
BEDIENUNGSANLEITUNG
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
ENGLISH ..... E1
香港電器安全規格
國際電工委員會規格適合
FRANÇAIS.... F1
ESPAÑOL .... S1
DEUTSCH .... D1
РУССКИЙ ..... Р1
（
）
(
)
CD-ROM
PN-E471
PN-E421
LCD MONITOR
ENGLISH
IMPORTANT INFORMATION
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
WARNING:
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous
CAUTION
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The AC outlet shall be installed near the equipment and shall be easily accessible.
Use the supplied power cord as it is.
CAUTION:
CAUTION:
This product utilizes fluorescent tubes containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling
information, please contact your local authorities.
E
1
IMPORTANT INFORMATION (Continued)
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the
manufacturer could void the user’s authority to operate this equipment.
NOTE:
This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of
these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities, the Electronics Industries Alliance:
(For U.S.A. Only)
This product contains a CR Coin Lithium Battery which contains Perchlorate Material – special handling may
U.S.A. ONLY
Attention: Your product is marked with this symbol. It means that used electrical and electronic products
should not be mixed with general household waste. There is a separate collection system for these products.
A. Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dustbin!
Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper
treatment, recovery and recycling of used electrical and electronic equipment.
Following the implementation by member states, private households within the EU states may return their used electrical and
electronic equipment to designated collection facilities free of charge*. In some countries* your local retailer may also take
back your old product free of charge if you purchase a similar new one.
*) Please contact your local authority for further details.
If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately beforehand
according to local requirements.
By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery and
recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due
to inappropriate waste handling.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t
B. Information on Disposal for Business Users
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the
costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local collection
facilities.
For Spain: Please contact the established collection system or your local authority for take-back of your used products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.
E
2
IMPORTANT INFORMATION (Continued)
The battery supplied with this product contains traces of Lead.
For EU:
The crossed-out wheeled bin implies that used batteries should not be put to the general household
waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in
accordance with legislation. Please contact your local authority for details on the collection and recycling
schemes.
For Switzerland:
The used battery is to be returned to the selling point.
For other non-EU countries:
Please contact your local authority for correct method of disposal of the used battery.
“BATTERY DISPOSAL”
THIS PRODUCT CONTAINS A LITHIUM PRIMARY (MANGANESS DIOXIDE) MEMORY BACK-UP BATTERY THAT
MUST BE DISPOSED OF PROPERLY. PLEASE CONTACT YOUR LOCAL SHARP DEALER OR AUTHORIZED SERVICE
REPRESENTATIVE FOR ASSISTANCE IN DISPOSING OF THIS BATTERY.
U.S.A. AND CANADA ONLY
DEAR SHARP CUSTOMER
Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your
product, please read the Safety Precautions carefully before using this product.
SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can
result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing,
operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the
following precautions carefully before using the product.
1. Read instructions — All operating instructions must be read and understood before the product is operated.
2. Keep this manual in a safe place — These safety and operating instructions must be kept in a safe place for future
reference.
3. Observe warnings — All warnings on the product and in the instructions must be observed closely.
4. Follow instructions — All operating instructions must be followed.
5. Cleaning — Unplug the power cord from the AC outlet before cleaning the product. Use a dry cloth to clean the product. Do
not use liquid cleaners or aerosol cleaners.
6. Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result
in accidents.
7. Water and moisture — Do not use the product near water. Do not install the product in a place where water may splash onto
it. Be careful of equipment which drains water such as an air-conditioner.
8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.
Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life
of the product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings.
Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
9. Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from
resting on them.
10. The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with
impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.
11. Overloading — Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.
12. Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage flows in
the product, and inserting an object can cause electric shock and/or short internal parts.
For the same reason, do not spill water or liquid on the product.
13. Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other
dangerous conditions. Request a qualified service person to perform servicing.
E
3
SAFETY PRECAUTIONS (Continued)
14. Repair — If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified service
person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls
not described in the instructions can cause damage, which often requires extensive adjustment work by a qualified
technician.
e. When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product
needs servicing.
15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement
parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of
unauthorized parts can result in fire, electric shock and/or other danger.
16. Safety checks — Upon completion of service or repair work, request the service technician to perform safety checks to
ensure that the product is in proper operating condition.
17. Wall mounting — When mounting the product on a wall, be sure to install the product according to the method
recommended by the manufacturer.
18. Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating
products (including amplifiers).
19. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment,
dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:
• Use the specified batteries only.
• Install the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the
compartment.
• Do not mix old and new batteries.
• Do not mix batteries of different types. Voltage specifications of batteries of the same shape may vary.
• Replace an exhausted battery with a new one promptly.
• If you will not use the remote control for a long time, remove the batteries.
• If leaked battery fluid gets on your skin or clothing, rinse immediately and thoroughly. If it gets into your eye, bathe your
eye well rather than rubbing and seek medical treatment immediately. Leaked battery fluid that gets into your eye or your
clothing may cause a skin irritation or damage your eye.
20. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury,
severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and
missile launch control in a weapon system.
21. Do not stay in contact with the parts of the product that become hot for long periods of time. Doing so may result in
low-temperature burns.
WARNING:
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate counter measures.
To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: PC/AV DVI-D output
terminal, PC/AV DVI-D input terminal, PC/AV HDMI input terminal, PC D-SUB input terminal, PC RGB input terminals, and
RS-232C input/output terminals.
If a monitor is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries,
particularly to children, can be avoided by taking simple precautions such as:
• Using fixing devices like wall mount brackets recommended by the manufacturer.
• Only using furniture that can safely support the monitor.
• Ensuring the monitor is not overhanging the edge of the supporting furniture.
• Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the
monitor to a suitable support.
• Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the monitor or its controls.
Especially for child safety
- Don’t allow children to climb on or play with the monitor.
- Don’t place the monitor on furniture that can easily be used as steps, such as a chest of drawers.
- Remember that children can become excited while watching a program, especially on a “larger than life” monitor. Care
should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.
- Care should be taken to route all cords and cables connected to the monitor so that they cannot be pulled or grabbed by
curious children.
E
4
TIPS AND SAFETY INSTRUCTIONS
- The TFT color LCD panel used in this monitor is made with
The Power Cord
the application of high precision technology. However, there
may be minute points on the screen where pixels never light
or are permanently lit. Also, if the screen is viewed from
an acute angle there may be uneven colors or brightness.
Please note that these are not malfunctions but common
phenomena of LCDs and will not affect the performance of
the monitor.
- Do not damage the power cord nor place heavy objects on
it, stretch it or over bend it. Also, do not add extension cords.
Damage to the cord may result in fire or electric shock.
- Use only the power cord supplied with the monitor.
- Do not use the power cord with a power tap.
Adding an extension cord may lead to fire as a result of
overheating.
- Do not display a still picture for a long period, as this could
cause a residual image.
- Do not remove or insert the power plug with wet hands.
Doing so could result in electric shock.
- Never rub or tap the monitor with hard objects.
- Unplug the power cord if it is not used for a long time.
- Please understand that SHARP CORPORATION bears no
responsibility for errors made during use by the customer or
a third party, nor for any other malfunctions or damage to this
product arising during use, except where indemnity liability is
recognized under law.
- Do not attempt to repair the power cord if it is broken
or malfunctioning. Refer the servicing to the service
representative.
Manual Scope
- Microsoft, Windows and Internet Explorer are registered
- This monitor and its accessories may be upgraded without
advance notice.
trademarks of Microsoft Corporation.
- Do not use the monitor where there is a lot of dust, where
humidity is high, or where the monitor may come into contact
with oil or steam, as this could lead to fire.
- HDMI, the HDMI Logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
- Ensure that the monitor does not come into contact with
water or other fluids. Ensure that no objects such as paper
clips or pins enter the monitor as this could lead to fire or
electric shock.
- Adobe, Acrobat, and Reader are either registered trademarks
or trademarks of Adobe Systems Incorporated in the United
States and/or other countries.
- Do not place the monitor on top of unstable objects or in
unsafe places. Do not allow the monitor to receive strong
shocks or to strongly vibrate. Causing the monitor to fall or
topple over may damage it.
- This product comes with RICOH Bitmap Fonts produced and
sold by RICOH COMPANY, LTD.
- All other brand and product names are trademarks or
registered trademarks of their respective holders.
- Do not use the monitor near heating equipment or in places
where there is likelihood of high temperature, as this may
lead to generation of excessive heat and outbreak of fire.
- Language of OSD menu used in this manual is English by
way of example.
- Illustrations in this manual may not exactly represent the
actual product or display.
- Images cannot be rotated on this monitor.
When using in vertical orientation, you will need to prepare
appropriately orientated content in advance.
- This manual assumes use in horizontal orientation, except
where specifically noted.
(PN-E471 cannot be used in vertical orientation.)
Fluorescent Tubes
● The fluorescent tubes in this product have a limited lifetime.
* If the screen gets dark, flashes or does not turn on, it may
be necessary to replace the fluorescent tubes. These
fluorescent tubes are exclusive to this product and must
be replaced by an authorized Sharp servicing dealer or
service center.
* Please contact your local Sharp servicing dealer or
service center for assistance.
● Because of the property of fluorescent tubes, the screen
may flash during the initial period of use. If this happens,
please turn off the main power switch of the monitor and
turn on again after at least 5 seconds to confirm operation.
E
5
MOUNTING PRECAUTIONS
• Since the monitor is heavy, consult your dealer before
installing, removing or moving the monitor.
• When installing, removing or moving the monitor, ensure
that this is carried out by at least 2 people.
• A mounting bracket compliant with VESA specifications
is required. Do not use any screw holes other than VESA
holes for installation.
• When moving the monitor, be sure to hold it with the
handles both on the rear and the unit bottom. Do not hold
the LCD panel. This may cause product damage, failure, or
injury.
• If it is difficult to provide sufficient space for any reason
such as the installation of the monitor inside a housing, or
if the ambient temperature may be outside of the range
of 32°F (0°C) to 104°F (40°C), install a fan or take other
measures to keep the ambient temperature within the
required range.
• Temperature condition may change when using the display
together with the optional equipments recommended by
SHARP. In such cases, please check the temperature
condition specified by the optional equipments.
• PN-E471 cannot be used in vertical orientation.
• Adhere to the following when installing the monitor in its
vertical orientation. Failing to adhere to the following may
cause malfunctions. (for PN-E421 only)
• Install the monitor with the surface perpendicular to a level
surface. If necessary, the monitor may be tilted up to 20
degrees upward or downward.
• Mounting the monitor on the wall requires special expertise
and the work must be performed by an authorized SHARP
dealer. You should never attempt to perform any of this
work yourself. Our company will bear no responsibility
for accidents or injuries caused by improper mounting or
mishandling.
• This monitor should be used at an ambient temperature
between 32°F (0°C) and 104°F (40°C). Provide
enough space around the monitor to prevent heat from
accumulating inside.
- Install the monitor such that the power LED is located on
the downside.
- Set the MONITOR on the SETUP menu to PORTRAIT.
(See Operation guide.)
• Do not block any ventilation openings. If the temperature
inside the monitor rises, this could lead to a malfunction.
• After mounting, please carefully ensure the monitor is
secure, and not able to come loose from the wall or mount.
• Do not place the monitor on a device which generates heat.
• Use the supplied vertical sticker when you install the
monitor in vertical orientation. (for PN-E421 only)
For the monitor in horizontal orientation
Unit: inch [cm]
7-7/8 [20]
*
2
[5]
2
[5]
2 [5]
For the monitor in vertical orientation
(for PN-E421 only)
Unit: inch [cm]
*
7-7/8 [20]
Logo
Do not remove the factory-affixed sticker but affix the logo
sticker over it. Be careful not to cover the remote control
sensor or buttons.
• Be sure to use a wall-mount bracket designed or
designated for mounting the monitor.
2
[5]
2
[5]
• This monitor is designed to be installed on a concrete wall
or pillar. Reinforced work might be necessary for some
materials such as plaster / thin plastic board / wood before
starting installation.
This monitor and bracket must be installed on a wall which
can endure at least 4 times or more the weight of the
monitor. Install by the most suitable method for the material
and the structure.
• When attaching an optional part, follow the steps described
in the manual for the optional part.
* This monitor can be installed close to a wall. However,
as the monitor emits heat during operation, please be
aware that this heat may discolor or alter the wall.
• For use only with UL Listed Wall Mount Brackets with
minimum weight/load: PN-E471: 102 kg. (224.9 lbs.),
PN-E421: 88 kg. (194.0 lbs.).
E
6
Contents
IMPORTANT INFORMATION............................................1
Removing the Handles..................................................10
Affixing the Stand Hole Protection Covers .................11
Preparing the Remote Control Unit..............................11
Installing the batteries ................................................11
Remote control operation range.................................11
Turning Power On/Off....................................................12
Turning on the main power.........................................12
Turning power on/off ..................................................12
Disabling power on/off operations..............................12
DEAR SHARP CUSTOMER..............................................3
SAFETY PRECAUTIONS..................................................3
TIPS AND SAFETY INSTRUCTIONS...............................5
MOUNTING PRECAUTIONS............................................6
Supplied Components.....................................................7
Connecting Peripheral Equipment.................................8
Connection with a PC or AV equipment .......................8
Connection when the PN-ZB01 (optional)
is attached....................................................................9
Connecting the Power Cord .........................................10
Binding Cables...............................................................10
This manual contains instructions regarding connection and installation.
For other instructions, refer to the instruction manuals in the “manual” folder on the included CD-ROM.
Adobe Reader is required in order to view the instruction manuals.
Supplied Components
If any component should be missing, please contact your dealer.
Liquid Crystal Display Monitor: 1
Remote control unit: 1
Cable clamp: 2
Power cord
R-03 battery (“AAA” size): 2
CD-ROM (Utility Disk for Windows): 1
Operation manual: 1
Stand hole protection cover: 2
Vertical sticker (Operation panel): 1 (for PN-E421 only)
Vertical sticker (Logo): 1 (for PN-E421 only)
Blank sticker: 1
Place a blank sticker onto the SHARP logo to cover the logo.
* Sharp Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.
* For environmental protection!
Do not dispose of batteries in household waste. Follow the disposal instructions for your area.
E
7
Connecting Peripheral Equipment
When the PN-ZB01 (optional)
is attached
1
2
3 4 5
6
14 12 13
7 9 10
Caution
Connection with a PC or AV equipment
• Be sure to turn off the main power switch and disconnect
the plug from the power outlet before connecting/
disconnecting cables. Also, read the manual of the
equipment to be connected.
• Be careful not to confuse the input terminal with the output
terminal when connecting cables. Accidentally reversing
cables connected to the input and output terminals may
cause malfunctions and the other problems.
1. PC/AV HDMI input terminal
•
•
•
Use a commercially available HDMI cable (conforming to
the HDMI standard) for PC/AV HDMI input terminal.
Set HDMI of INPUT SELECT on the OPTION menu
according to the device to be connected.
Select the audio input terminal to be used in PC HDMI
or AV HDMI of AUDIO SELECT on the OPTION menu.
When HDMI is selected, connection to the audio input
terminal is unnecessary.
TIPS
• Images may not be displayed properly depending on the
computer (video card) to be connected.
2. PC D-sub input terminal
•
When the PN-ZB01 (optional) is attached, select the audio
input terminal to be used in PC D-SUB of AUDIO SELECT
on the OPTION menu.
• A screen with 1920 x 1080 resolution may not be displayed
correctly on PC RGB. In this case, check the settings of
your computer (video card) to verify that input signals
conform to specifications of this monitor. (See Operation
guide.)
3. Audio input terminal
•
•
Use an audio cable without resistance.
• If there is a check box to disable EDID in display control
panel, check it when using PC RGB.
When the PN-ZB01 (optional) is attached, set the audio
input terminal used for each input mode in AUDIO
SELECT on the OPTION menu.
• Use the automatic screen adjustment when a PC screen
is displayed for the first time using PC D-SUB or PC RGB,
or when the setting of the PC is changed. The screen is
adjusted automatically when SELF ADJUST in the OPTION
menu is set to ON.
• If the audio output from the playback device is connected
directly to speakers or other devices, the video on the
monitor may appear delayed from the audio portion.
Audio should be played through this monitor by connecting
the playback device to the monitor’s audio input, and
connecting the monitor’s audio output to the speakers or
other devices.
4. Audio output terminals
•
•
The output sound varies depending on the input mode.
The volume of the output sound can be fixed by setting
AUDIO OUTPUT on the OPTION menu.
•
It is not possible to control the sound output from the
audio output terminals with the AUDIO menu.
5. RS-232C input terminal
RS-232C output terminal
•
You can control the monitor from a PC by connecting a
commercially available RS-232 straight cable between
these terminals and the PC.
• The audio input terminals used in each input mode are
factory-set as follows.
Audio input terminal
Input mode
(Factory setting)
PC D-SUB, PC DVI-D,
Audio input terminal
PC RGB
AV DVI-D
AV COMPONENT,
AV S-VIDEO, AV VIDEO
PC HDMI, AV HDMI
Audio1 input terminal
Audio2 input terminal
PC/AV HDMI input terminal
E
8
Connecting Peripheral Equipment
14. PC/AV DVI-D output terminal
Connection when the PN-ZB01
(optional) is attached
The PN-ZB01 expansion board (optional) allows the use of
additional connection terminals.
•
•
•
The video of the PC/AV DVI-D input can be output to an
external device.
Outputting HDCP-encrypted video requires an external
device which supports HDCP.
This terminal allows the daisy chain connection of up to 5
monitors.
6. PC/AV DVI-D input terminal
•
Set DVI of INPUT SELECT on the OPTION menu
according to the device to be connected.
TIPS
•
Select the audio input terminal to be used in PC DVI-D or
AV DVI-D of AUDIO SELECT on the OPTION menu.
• The length of the signal cables or surrounding environment
may affect the image quality.
7. PC RGB input terminals
•
• The screen may not display properly when using terminals
other than PC DVI-D/AV DVI-D for the input mode. In this
case, turn off the power to all the monitors connected in a
daisy chain and then turn the power on again.
• When connecting monitors in a daisy chain set AUTO
INPUT CHANGE to OFF.
Set BNC of INPUT SELECT on the OPTION menu to PC
RGB when using the PC RGB input terminals.
Select the audio input terminal to be used in PC RGB of
AUDIO SELECT on the OPTION menu.
•
8. AV component input terminals
• Video output is disabled in the following cases:
When the input mode is PC HDMI/AV HDMI
When PIP SOURCE of the PIP/PbyP menu is set to PC
HDMI or AV HDMI
When the power is turned off
When the monitor is in input signal waiting mode
•
Set BNC of INPUT SELECT on the OPTION menu to
AV COMPONENT when using the AV component input
terminals.
Select the audio input terminal to be used in AV
COMPONENT of AUDIO SELECT on the OPTION menu.
•
9. AV video input terminal
•
Select the audio input terminal to be used in AV VIDEO of
AUDIO SELECT on the OPTION menu.
10. AV S-video input terminal
•
Select the audio input terminal to be used in AV S-VIDEO
of AUDIO SELECT on the OPTION menu.
11. Audio1 input terminals / Audio2 input terminals
•
Set the audio input terminal to be used in each input
mode in AUDIO SELECT on the OPTION menu.
12. LAN terminal
•
You can control the monitor from a PC on a network by
connecting a commercially available LAN cable between
this terminal and a network.
13. External speaker terminals
•
To use external speakers, set SPEAKER SELECT on the
SETUP menu to EXTERNAL.
•
Be sure to use external speakers with an impedance of 6
Ω or greater and a rated input of at least 10 W.
1
2
3
Approx.
3-15/16 inch
(10 cm)
1. Attach a speaker cable core (included with the PN-ZB01) to
the end of the speaker cable connected to the monitor.
2. While pushing the tab, insert the tip of the cable.
3. Release the tab.
TIPS
• Be sure to connect the + and - terminals and the left and
right speakers properly.
• Avoid short circuiting the + and - terminals.
• When SPEAKER SELECT is set to EXTERNAL, the
internal speakers are disabled.
E
9
Connecting the Power Cord
Caution
• Do not use a power cord other than the one supplied with
the monitor.
1. Turn off the main power switch.
2. Plug the power cord (supplied) into the AC input terminal.
3. Plug the power cord (supplied) into the AC power outlet.
3
For power
outlet
Main power switch
2
1
Binding Cables
[PN-E471]
The cables connected to the terminals on the rear of the
monitor can be fastened with the cable clamp.
Insert the cable clamp into the cable clamp attachment on the
rear of the monitor and fasten the cables.
Cable
Cable clamp
attachment
[PN-E421]
Cable clamp
Removing the Handles
Handle
The handles can be removed.
The removed handles can be attached on the rear side.
Caution
Handle screws
• The removed handles and handle screws are for use with
this monitor. Do not use them for any other devices.
• To attach handles, be sure to use the handles and handle
screws which were removed from the monitor.
• Be sure the handles are attached securely.
Handle
Handle screws
E
10
Affixing the Stand Hole Protection Covers
After installing the monitor, affix the stand hole protection
covers as necessary.
1. Peel off the backing sheet and affix the cover on the
monitor.
Preparing the Remote Control Unit
Installing the batteries
Remote control operation range
1. Press the cover gently and slide it in the direction of the
arrow.
The operation range of the remote control unit is approx. 16.4
feet (5 m) at an angle of approx 10° from the center to the top/
bottom/right/left of the remote control sensor.
Remote control
sensor
2. See the instructions in the compartment and put in the
supplied batteries (R-03 (“AAA” size) x 2) with their plus (+)
and minus (-) sides oriented correctly.
10°
16.4 feet
(5 m)
10°
10°
3. Close the cover.
10°
TIPS
• When the batteries become exhausted replace them with
new (commercially available) batteries.
• The supplied batteries (R-03 (“AAA” size) x 2) may become
exhausted quickly depending on how they are stored.
• If you will not be using the remote control for a long time,
remove the batteries.
• Use manganese or alkaline batteries only.
TIPS
• Do not expose the remote control unit to shock by dropping
or stepping on it. This could lead to a malfunction.
• Do not expose the remote control unit to liquids, and do not
place it in an area with high humidity.
• The remote control unit may not work properly if the remote
control sensor is under direct sunlight or strong lighting.
• Objects between the remote control unit and the remote
control sensor may prevent proper operation.
• Replace the batteries when they run low as this may
shorten the remote control’s operation range.
• If a fluorescent light is illuminated near the remote control
unit, it may interfere with proper operation.
• Do not use it with the remote control of other equipment
such as air conditioner, stereo components, etc.
E
11
Turning Power On/Off
Caution
TIPS
• Turn on the monitor first before turning on the PC or
playback device.
• If the monitor is in the input signal standby mode and you
press the POWER button on the remote control unit, the
monitor enters standby mode.
• You can turn on/off the monitor by pressing the power
switch on the front panel of the monitor.
Turning on the main power
• Setting the SCHEDULE flashes the power LED alternately
in red and orange in standby mode.
Date/time setting
n
• If the time has yet to be set when the monitor is first turned
on, the date/time setting screen appears. Set the date and
time.
DATE/TIME SETTING
/
/
:
:
Main power switch
SET
20 09
/
01
/
01
00
:
00
CANCEL
Caution
• The main power must be turned on/off with the main power
switch. Do not connect/disconnect the power cord or turn
the breaker on/off while the main power switch is on.
• When switching the main power switch or the POWER
button off and back on, always wait for at least 5 seconds.
OK···[MENU]
1. Press
,
,
or
to select the date and time,
and press
or
to change the numerical values.
2. Select SET and then press
• Be sure to set the date and time.
.
Turning power on/off
Press the POWER button to turn the power ON/OFF.
When the main power switch is off, the monitor cannot be
turned on using the POWER button on the remote control unit.
• The date/time setting screen will close automatically if no
operation is performed for about 15 seconds. The date
and time can be set using DATE/TIME SETTING from
the OPTION menu when the date/time setting screen
disappears.
TIPS
•
•
•
•
Set the date in “Year/Month/Day” order.
Set the time on a 24-hour basis.
The clock is maintained by the internal battery.
If you already set the time but the date/time setting
screen appears when the power is turned on, the
internal battery may be exhausted. Please contact
your local Sharp servicing dealer or service center for
assistance with battery replacement.
Power LED
•
•
Estimated service life of the internal battery: About 5
years (depending on monitor operation)
As the first battery was inserted at the factory, it may be
exhausted prior to the expected continuous operation
life.
Status of a power LED
Green lighting
Status of the monitor
Power on
Orange lighting
Power off (Standby mode)
Input signal waiting mode
Green flashing
Caution
Disabling power on/off operations
• When switching the main power switch or the POWER
button off and back on, always wait for at least 5 seconds.
A short interval may result in a malfunction.
Power on/power off operations can be disabled in order to
protect the monitor from an accidental power off. Set the
ADJUSTMENT LOCK in FUNCTION menu to “2”. (See
Operation guide.)
E
12
Printed in China
Imprimé en Chine
Impreso en China
Gedruckt in China
Отпечатано в Китае
0NY42M184305B(1)
Q41G42M1843 5B
|