Audiobeam
Instructions for use
Contents
Safety instructions ......................................................................................................................... 2
Warning – High Voltage – Risk of Death! ................................................................................... 2
Risk of fire! ........................................................................................................................................ 2
Is there a danger of hearing damage? ........................................................................................ 2
How Audiobeam works .................................................................................................................. 2
Connections and operating controls ............................................................................................ 3
Mounting Audiobeam .................................................................................................................... 4
Correct mounting conditions ......................................................................................................... 4
Mounting Audiobeam in a fixed position ................................................................................... 4
Mounting Audiobeam movably or rotatably ............................................................................. 4
Distance sensor ................................................................................................................................ 4
Putting Audiobeam into operation .............................................................................................. 4
Manufacturer declarations ............................................................................................................ 7
Warranty regulations ...................................................................................................................... 7
CE Declaration of Conformity.......................................................................................................... 7
WEEE Declaration ............................................................................................................................. 7
Thank you for choosing Sennheiser!
We have designed this product to give you reliable operation over many years. Over half a
century of accumulated expertise in the design and manufacture of high-quality electro-
acoustic equipment have made Sennheiser a world-leading company in this field.
Please take a few moments to read these instructions carefully, as we want you to enjoy your
new Sennheiser products quickly and to the fullest.
1
Safety instructions
Warning – High Voltage – Risk of Death!
Opening the Audiobeam while it is connected to the mains is likely to result in a life-
threatening electric shock!
There are no user serviceable parts inside – if the Audiobeam should become defective, any
repairs must be carried out by an official Sennheiser Service Partner. If the unit is opened in
breach of this instruction, the warranty becomes null and void.
Risk of fire!
Audiobeam generates heat! Make sure that the air vents of the unit are not covered or
blocked! Keep Audiobeam away from heat sources and never expose Audiobeam to direct
sunlight! Maintain a minimum distance of 1 meter between Audiobeam and combustible
materials.
Attention!
If liquids or small parts which conduct electricity find their way into the interior or to the
connecting sockets of Audiobeam, this can cause a short circuit! Use Audiobeam in dry rooms
only and keep liquids and small parts which conduct electricity away from the unit and its
connecting sockets. For cleaning Audiobeam, only use a dry or slightly damp cloth. Never use
any solvents or cleansing agents.
Is there a danger of hearing damage?
A new study tested the Audiobeam for possible damage to hearing due to the ultrasound it
emits and certified its harmlessness. In this study, Prof. Dr.-Ing. Joachim Herbertz, the
President of the first International Ultrasonics Congress, came to the following conclusion:
“The ultrasound emitted by the Sennheiser Audiobeam is safe at a minimum distance of 20
cm from the protective grid”.
The limit values of the European and international standards and guidelines IEC 71672-1, IEC
61012, GEFAU N 01 and 2003/10/EG are complied with.
How Audiobeam works
Audiobeam is an acoustic spotlight. This means:
y Audiobeam is able to focus sound – either directly or via reflections on a surface. This allows
e.g. information in museums and at exhibitions to be radiated directly from the exhibits –
only visitors standing directly in front of an exhibit are addressed.
y Audiobeam limits sound reproduction to precisely defined areas – adjacent areas are kept
sound-free. This helps to create a calmer overall atmosphere in rooms. Several Audiobeams
can be installed in one room without affecting each other.
y Astonishing audio effects amaze visitors as Audiobeam allows the sound to come from
unusual directions.
Audiobeam uses state-of-the-art ultrasonic sound transmission technology:
Audiobeam works with ultrasound, modulating the audible sound onto an ultrasonic carrier
frequency. Due to the nonlinearity of air, the desired audio signal is produced by the self-
demodulation effect of the ultrasound wave. At an angle of 30°, a slim sound beam is created
that can be heard over long distances.
2
Connections and operating controls
Delivery includes
¾
y Audiobeam
y 3 mains cables with connectors
5
y /83" thread with adapter
to /8" thread
y Instruction for use
y Warranty Certificate
·
³
»
¶
¾
º
¾
¿
´
²
µ
³ LED operation indicator: green: Audiobeam is operational (standby)
red: Audiobeam is not operational
· Sensitivity selector switch (+6 dBm, –14 dBm)
» On/off switch for distance sensor is set to “ON”
¿ XLR-3 socket for audio input INPUT
´ OVERLOAD LED
² BNC socket for carrier signal output OUTPUT
5
3
¶ /8" thread with adapter to /8" thread
º IEC mains socket
¾ Air vents
µ Steel clamp for securing the mains cable
3
Mounting Audiobeam
Correct mounting conditions
̈ When mounting Audiobeam, make sure that:
y the ultrasonic sound wave can travel undisturbed for at least 1 m before it strikes the
first surface.
y a minimum distance of 10 cm is maintained between Audiobeam and adjacent objects
so that any heat generated can dissipate. Make sure that the air vents at the top and
rear of the unit are not covered or blocked!
y a minimum distance of 1 meter is maintained between Audiobeam and combustible
materials.
y Audiobeam is kept away from heat sources such as central heating radiators, spot lights
and lamps. Never expose Audiobeam to direct sunlight.
y Audiobeam never gets wet.
Mounting Audiobeam in a fixed position
To ensure that Audiobeam is always orientated towards the correct area of interest, you
should mount Audiobeam in a fixed position. Use a mounting plate for wall or ceiling
5
̈ Screw the mounting plate or the table or floor stand to the /8" thread. Use the thread
adapter ¶ if necessary.
Audiobeam towards the correct area of interest or the reflection area.
¶
Mounting Audiobeam movably or rotatably
5
̈ Screw Audiobeam onto a drive mechanism or a rotating mechanism using the /8" thread.
Use the thread adapter ¶ if necessary.
Distance sensor
For reasons of test engineering, a distance sensor ³ with a switch » is located on the bottom
right of the emitter surface.
If the distance sensor is “on”, the Audiobeam turns off whenever persons or objects are
situated at a distance of less than four meters in the emitting direction of the Audiobeam.
For this reason, the distance sensor is factory-preset to “off” and should as a rule stay like this
during operation in order to prevent automatic turn-off (for further information, please refer
to the service instructions).
»
³
Putting Audiobeam into operation
̈ Ensure that Audiobeam is not connected to the mains !
̈ Use the sensitivity selector switch · to adapt Audiobeam’s input sensitivity to the audio
source:
y Audio sources with a high output power (e.g. mixing console, CD or DVD player):
upper position (+6 dBm).
·
y Audio sources with a low output power (e.g. portable mini disk player):
lower position (–14 dBm).
4
̈ Use an XLR-3 cable to connect the audio source (e.g. CD or DVD player, mixing console,
receiver of a wireless microphone) to the audio input INPUT ¿.
Audiobeam automatically emits ultrasound as soon as an audio signal (see
̈ Use the mains cable º to connect Audiobeam to the mains. Secure the mains cable with
the steel clamp µ.
̈ The LED operation indicator ³ lights up green, indicating that Audiobeam is ready for
operation (standby).
µ
Note: If you do not use the unit for a period, disconnet the mains connector from the wall
socket. This helps to increase the service life of Audiobeam and save energy.
Troubleshooting
If the LED operation indicator ³ lights up red, one of the following problems may have
occured:
On/off switch for distance sensor is activated
̈ Someone has entered the security area of four meters in front of or around the Audiobeam
and the motion sensor has triggered. After the person has left this area, Audiobeam
automatically turns on again after 30 seconds.
³
̈ Solution: Set the on/off switch for the distance sensor » to “off”.
Audiobeam is defective
̈ Please contact your Sennheiser distributor or the Sennheiser Service department (for
address, see last page).
Accessories
The following accessories are available from your Sennheiser distributor:
GZP 10 Mounting plate for wall and ceiling mounting
1
GZG 1029 Swivel joint for attachment to stands or the GZP 10 mounting plate, includes /4"
interchangeable thread
3
MZT 14 Mounting bolt for mounting goosenecks and swivel joints with /8" thread to table tops
MZT 100 Stable, metal table stand with /8" thread
3
3
MZT 1019 Mounting bar for two units with /8" internal thread
3
SEMS 3134 Floor stand with /8" thread
5
Specifications
Modulation:
wideband AM
Carrier frequency:
Peak limiter:
40 kHz
limiter amplifier
Audio channels:
Audio input:
1
XLR-3F socket, balanced, DC-isolated
Input level for max. peak SPL: +6 dBm (1.55 V) = upper switch position
–14 dBm (150 mV) = lower switch position
Switching threshold:
–46 dBm (4 mV) = upper switch position
–66 dBm (0.4 mV) = lower switch position
Impedance:
600 Ω
Sound pressure level:
Output:
75 dB ± 5 dB (at a distance of 4 m)
1 x BNC, 50 Ω shortcircuit-proof
approx. 90 W
Amplifier power:
Power supply:
switchable power supply 110 - 240 V,
50 - 60 Hz max. 100 W
Dimensions:
Weight:
264 x 82 x 320 mm
approx. 4 kg
XLR-3 pin assignment:
+NF
1
2
3
-NF
6
Manufacturer declarations
Warranty regulations
The guarantee period for this Sennheiser product is 24 months from the date of purchase.
Excluded are accessory items and disposable batteries that are delivered with the product;
due to their characteristics these products have a shorter service life that is principally
dependent on the individual frequency of use.
The guarantee period starts from the date of original purchase. For this reason, we
recommend that the sales receipt be retained as proof of purchase. Without this proof (which
is checked by the responsible Sennheiser service partner) you will not be reimbursed for any
repairs that are carried out.
Depending on our choice, guarantee service comprises, free of charge, the removal of material
and manufacturing defects through repair or replacement of either individual parts or the
entire device. Inappropriate usage (e.g. operating faults, mechanical damages, incorrect
operating voltage), wear and tear, force majeure and defects which were known at the time
of purchase are excluded from guarantee claims. The guarantee is void if the product is
manipulated by non-authorised persons or repair stations.
In the case of a claim under the terms of this guarantee, send the device, including acces-
sories and sales receipt, to the responsible service partner. To minimise the risk of transport
damage, we recommend that the original packaging is used. Your legal rights against the
seller, resulting from the contract of sale, are not affected by this guarantee.
The guarantee can be claimed in all countries outside the U.S. provided that no national law
limits our terms of guarantee.
CE Declaration of Conformity
This equipment is in compliance with the essential requirements and other relevant
provisions of Directives 1999/5/EC, 89/336/EC or 73/23/EC. The declaration is available on
Before putting the device into operation, please observe the respective country-specific
regulations!
WEEE Declaration
Your Sennheiser product was developed and manufactured with highquality
materials and components which can be recycled and/or reused. This symbol
indicates that electrical and electronic equipment must be disposed of separately
from normal waste at the end of its operational lifetime.
Please dispose of this product by bringing it to your local collection point or recycling centre
for such equipment. This will help to protect the environment in which we all live.
7
Sennheiser electronic GmbH & Co. KG
30900 Wedemark, Germany
Phone +49 (5130) 600 0
Fax +49 (5130) 600 300
Printed in Germany
Publ.05/06
089056/A1
|