®
AT8400™ AllTouch
Remote Control
User’s Guide
If you program codes to control devices,
record your codes here:
CBL: _____________________
TV:_______________________
VCR: _____________________
AUX: _____________________
Welcome to the Ultimate Control Experience!
Your new AT8400™ AllTouch® Universal Remote Control (remote) is a true universal
remote, functioning as four remotes in one. As one example, you can use this remote to
operate your TV, VCR, cable box, and receiver.
How Does A Universal Remote Control Work?
You tell the remote which type of device you want to operate using the four keys arched
across the top of the remote. These keys, known as mode keys, are labeled CBL, TV,
VCR, and AUX. Each mode key is associated with a specific device. As an example, if
you want the remote to operate your TV, you simply press the TV key. Other keys you
press on the remote thereafter should operate your TV. Want to switch the remote to
operate a different device? Just press the mode key for the next device you want to
operate. In this guide, you will learn which types of devices you can control and how
to program the remote to control your specific devices.
Note: Some remote keys may not operate in all modes. You can even program your
remote to assign specific functions, such as channel control, to operate one device only.
You will learn more about these advanced functions later in this guide.
Where Do I Start?
Before you begin programming your remote, complete the following initial setup tasks.
Install the Batteries
The remote requires two AA batteries (alkaline recommended). A diagram in the battery
compartment of the remote indicates proper placement of the batteries. When batteries
are properly installed, the light on the remote blinks each time a key is pressed.
Visit the Quick Reference
Timing is often important when you program advanced features. Therefore, knowing
where certain keys are on the remote gives you an edge in pressing the right key at the
right time.
Find a Place to Store Your Remote
Keeping up with one remote is much easier than keeping up with four remotes. How-
ever, it is still a good idea to find a storage location for your remote. The AT8400
AllTouch Remote Control is not a toy. It should be kept out of the reach of children
under the age of 6 years.
Important Information About Power Control
Scientific-Atlanta strongly recommends that you turn off your cable box every time you
turn off your TV. To make this easier, you can program your remote to turn both devices
on or off at the same time. After you program the remote to control your four favorite
entertainment devices, see Change Power Control to learn more about programming
your remote to control power for the TV and cable box at the same time.
3
Quick Reference
1
2
3
36
35
34
33
4
5
32
31
30
6
7
29
8
28
27
26
25
9
10
11
12
13
14
24
23
22
15
16
21
20
19
18
17
T9857
Device Control
Sound
1
Powers on or off
29
27
Adjusts volume
Mutes sound
35
36
2
AUX Mode key
VCR Mode key
TV Mode key
3
Cable Mode key
4
Viewing and Browsing Control
DVR Control
26
Replays the previous few
seconds of a program
33
Displays the program guide
34
Displays the Applications
Menu
10
Displays a list of programs
that you have recorded, so
that you can select one for
viewing
4
5
Displays channel and
program information
Navigates through settings or
the program guide
11
Displays live television
programming
32
7
Moves through selections
VCR/VOD (Video On Demand) Control
Selects and deselects screen
item
Note: In VCR mode, these keys control
your VCR.
31
6
Displays the General
Settings or Quick settings
menus
25
13
12
24
23
14
Rewinds VCR/VOD
Plays VCR/VOD
Fast forwards VCR/VOD
Stops VCR/VOD
Exits settings, menus, and
guides
30
8
Selects options in menus
and the program guide
Pauses VCR/VOD
Records program
Selects channel, up or down
Views favorite channels
28
9
PIP (Picture In Picture) Control
20
Opens or closes the PIP
window
Returns to last channel
viewed
19
Swaps the contents of the
PIP window and the main
viewing screen so that the
PIP window displays on
the main screen
22
Enters channel numbers
and remote codes (also
enters your parental
control PIN)
21
15
Reserved for future use
Reserved for future use
16
Moves the PIP window
to another location on
the screen
17
18
Selects the channels in the
PIP window, up or down
Selects the video source
5
What Devices Can I Control?
The mode keys arched across the top of the remote tell the remote which device you
want to operate.
Each mode key is associated with different groups
of devices. You can use each mode key to control
one of its associated devices:
Mode Key Associated Devices
CBL .......... cable boxes and satellites
TV............. TVs and HDTVs
VCR ......... VCRs, DVD players, PVRs (personal video recorders), and CD players
AUX ......... receivers, amplifiers, and tuners
What Devices Do I Want to Control?
Record the devices (including brand) you want to control here:
1_____________________________
2_____________________________
3_____________________________
4_____________________________
Does each mode key relate to only one of your devices? If yes, go to Program the
Remote to Control My Devices. Otherwise, reassign mode keys to match your
combination of devices.
Reassign Mode Keys
If you are a big movie fan, you may want to control two video recording devices.
Perhaps you have a DVD player and a VCR, or a VCR/DVD combination device. How
can you control both the VCR and the DVD player when you only have one VCR key?
With the AT8400, you can reassign a mode key to operate in a different mode. For
example, you can reassign the AUX key to operate in VCR mode. Then, you can
program the AUX key to control your DVD player. You can reassign the AUX key, the
VCR key, or both. The TV key and the CBL key cannot be reassigned.
Reassigning Mode Keys
(Program Code 9 9 2)
1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Press 9 9 2. The CBL mode key blinks twice.
3. Press the mode key associated with the type of device you want to control, and then
press the mode key that you want to change. All mode keys blink three times.
Some Common Examples
• To program the AUX key to operate in VCR mode, press VCR and then AUX.
• To program the VCR key to operate in TV mode, press TV and then VCR.
4. When finished, go to Program the Remote to Control My Devices.
6
Program the Remote to Control My Devices
Try to use your remote to control your devices. If the remote does not work for a device,
you can assign a different device code to the appropriate mode key. If the remote
provides only limited functionality for a device, you can look for a code that provides
more functionality. Before you begin, make sure you know the brand name of the device
you want to control.
Note: Some remote keys may be assigned to operate one device type only. For example,
volume control may be assigned to the TV only. If this is the case, you can reprogram
power, volume, and channel control using procedures later in this guide.
Assigning a Different Device Code to a Mode Key
1. Find the codes for your brand of device in the appropriate setup code list at the end
of this guide. For example, look under TV Group if you need to program the remote
to operate your TV.
2. Turn on your device.
3. Press and hold SELECT and the appropriate mode key until all of the mode keys
blink twice. For example, to set up the TV, press and hold SELECT and TV.
Note: If you reassigned mode keys, you may, for example, press SELECT and VCR
to program the VCR mode key with a TV code.
4. Enter the first setup code for the device. All mode keys blink twice to indicate that
the code entry was accepted.
5. Point the remote at the device, and press POWER,
, or
to test the device.
6. Did the device operate correctly?
• If yes, write down the code that worked on the cover of this guide.
You may need it again if the device code is accidentally erased.
• If no, repeat these steps using a different setup code.
Note: If none of the codes listed for your brand of device operate the device
correctly, go to What If None of the Codes Work for instructions.
7. Repeat this procedure for each mode key you want to program.
7
What If None of the Codes Work?
If none of the codes listed for your brand of device operate the device correctly, you can
search through the code library for a valid code.
Improving Your Reaction Time
When you search the code library, you need to be ready to press SELECT as soon as the
remote turns off your device. Therefore, make sure you are familiar with the location of
the SELECT key before you begin this procedure.
Sizing Up The Libraries
The mode keys blink twice when the remote reaches the last code in a library. You
do not need to count codes. However, knowing the size of each library will help you
determine how long it will take to cycle through all of the codes in the library. Each
library contains the following number of codes:
• CBL mode: 15
• TV mode: 184
• VCR mode: 176
• AUX mode: 21
Searching the Code Library
(Program Code 9 9 1)
1. Turn on the device.
2. Press and hold SELECT and the appropriate mode key (CBL, TV, VCR, or AUX)
until the mode keys blink twice. For example, to search for a TV code, press and
hold SELECT and TV at the same time.
Note: If you reassigned mode keys, you may, for example, press SELECT and
VCR to search for a TV code to assign to the VCR mode key.
3. Press 9 9 1. The mode key you selected in step 2 blinks twice.
4. Point the remote toward the device, and press
. The remote automatically tests
each code in its library, beginning with the most common codes. The mode key
blinks once each time the remote transmits a new code. The mode key blinks twice
when it reaches the last code.
5. As soon as the device powers off, press SELECT.
6. Verify the new code is correct by pressing POWER.
7. Did the device power on again?
• If yes, press SELECT to assign the code.
• If no, complete the following steps:
a) Turn the device on.
b) Press
or
to step forward or back to the correct code.
c) When the device turns off, press SELECT to assign the code.
8. Go to Which Code Worked to identify the code that controls your device. After you
identify the code, record the code in the space provided on the cover of this guide.
8
Which Code Worked?
Find out which code programmed the mode key to control your device.
Finding the Code That Worked
(Program Code 9 9 0)
1. Press and hold SELECT and the appropriate mode key (CBL, TV, VCR, or AUX)
until all mode keys blink twice.
2. Press 9 9 0. The mode key you selected in step 1 blinks twice.
3. Press 1; then, count the number of times the mode key blinks. The number of blinks
indicates the first digit in the code. For example, 4 blinks indicates the first digit in
the code is 4. If the mode key does not blink, the digit is 0.
4. Press 2; then, count the number of times the mode key blinks. This number indicates
the second number in the code.
5. Press 3; then, count the number of times the mode key blinks. This number indicates
the third number in the code.
6. Press 4; then, count the number of times the mode key blinks. This number indicates
the fourth number in the code.
After all four numbers in the code are identified, all mode keys blink three times.
7. Record the code in the space provided on the cover of this guide. You may need it
again if the device code is accidentally erased.
9
Change Power Control
Your remote is originally programmed in one of the following ways:
•
The remote controls power for only one device at a time. For example, in CBL mode
the POWER key controls the cable box only. However, in TV mode, the POWER key
controls the TV only.
•
The remote controls power for either one device or for multiple devices at once,
based on the selected mode. For example, in CBL mode, the POWER key controls
both the cable box and the TV at the same time.
Before you change how power control works, try your remote to see how the power
control currently works. When trying out your remote, keep in mind that the remote
provides a temporary override for power control. For example, if you press the TV key
and then the POWER key within 3 seconds, the remote turns on the TV only, regardless
of the programmed power settings. To see how the remote is originally programmed,
wait at least 5 seconds before pressing the POWER key after you press any mode key.
Does your remote already control power for your cable box and TV at the same time?
If not, Scientific-Atlanta strongly recommends that you program the remote to turn off
the cable box each time you turn off your TV. Turning off the cable box is especially
important for high-end cable boxes that contain hard drives for recording and storing
TV programs and movies. Not only will you reduce wear and tear from the hard disk
spinning constantly, but you'll also conserve electricity. As long as the cable box remains
plugged in, the cable box will receive programming updates, and, if applicable, record
programs and movies.
Controlling Power for Multiple Devices at Once
(Program Code 9 9 8)
1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Press 9 9 8. The CBL key blinks twice.
3. Press the mode key for the first device in the group of devices you want to power on
and off at once. The CBL key blinks twice.
4. Press the mode key for the second device in your power group. The CBL key blinks
twice.
5. If you want the remote to control power for 3 or 4 devices at once, press the mode
keys for the next devices you want to add to the power group. The CBL key blinks
twice after each mode key is pressed.
6. Press SELECT to save your power settings. All mode keys blink three times.
10
Want An Example?
If you want to control power for the TV and the cable box at the same time, you would
do the following:
1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Press 9 9 8. The CBL key blinks twice.
3. Press TV. The CBL key blinks twice.
4. Press CBL. The CBL key blinks twice.
5. Press SELECT. All mode keys blink three times.
In this example, the remote will function in the following ways:
•
When you are in TV mode or CBL mode, the POWER key controls both the cable
box and the TV.
•
•
When you are in VCR mode, the POWER key controls the VCR device only.
When you are in AUX mode, the POWER key controls the auxiliary device only.
Controlling Power for One Device at a Time
(Program Code 9 9 8)
1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Press 9 9 8. The CBL key blinks twice.
3. Press SELECT to save your power settings. All mode keys blink three times.
After you select a mode, the POWER key controls the device assigned to that mode.
For example, in TV mode, the remote controls power for the TV only.
Important Power Tips
•
At a minimum, Scientific-Atlanta strongly recommends that you program the remote
to turn off the cable box each time you turn off your TV.
•
When you “turn off” the cable box using the remote control, you are actually putting
the box in a power saving mode. As long as the cable box remains plugged in, it will
continue to receive programming updates and, if applicable, record programs and
movies.
•
•
If your POWER key controls multiple devices at once, the remote returns to the CBL
mode after the devices are powered on or off.
If your POWER key controls multiple devices at once, you can override this setting
by pressing the desired mode key and then pressing POWER within 3 seconds. For
example, if you press the VCR key and then the POWER key within 3 seconds, the
remote turns just the VCR on or off, regardless of the programmed power settings.
11
Change Volume Control
Your remote is originally programmed in one of the following ways:
•
The remote controls volume for one device, such as your TV, whether the remote is
in TV, VCR, or CBL mode. The AUX mode always retains separate volume control.
•
The remote controls volume for different devices, depending on the mode key you
press. For example, in CBL mode, the volume keys control the cable box. However,
in TV mode, the volume keys control the TV.
Try your remote to see how the volume control currently works. The volume keys
include and MUTE. If you want to change the volume control, complete the
procedure that fits your needs.
,
Controlling Volume for One Device
(Program Code 9 9 3)
Note: If you want to assign volume control to a Scientific-Atlanta cable box, complete
the following prerequisite steps. Press SETTINGS to access the General Settings
on-screen menu. Then, verify that the Audio: Volume Control setting is set to Variable.
1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Press 9 9 3. The CBL key blinks twice.
3. Press the mode key for the device the volume keys should control. For example, if
you want to control volume through your TV, press TV. All mode keys blink
three times.
The volume keys control only one device whether you are in CBL, TV, or VCR mode.
Note: In AUX mode, the remote always controls volume for the device assigned to
the AUX key.
Controlling Volume for Different Devices
(Program Code 9 9 3)
1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Press 9 9 3. The CBL key blinks twice.
3. Press SELECT. All mode keys blink three times.
After you select a mode, the volume keys control the device assigned to that mode. For
example, in TV mode, the volume keys control volume for the TV only.
12
Change Channel Control
Your remote is originally programmed in one of the following ways:
•
The remote controls channels for a single device, such as the cable box, whether the
remote is in CBL, VCR, or TV mode. The AUX mode always retains separate
channel control.
•
The remote controls channels for different devices, depending on the mode key you
press.
Try your remote to see how the channel control currently works. The channel keys
include , Digits 0-9, LAST, and FAV. If you want to change the channel control,
complete the procedure that fits your needs.
,
Tip: Consider programming the remote to control channels for just the cable box to
ensure you do not accidentally tune off the proper channel for the TV (usually channel
3 or 4).
Controlling Channels For One Device
(Program Code 9 9 7)
1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Press 9 9 7. The CBL key blinks twice.
3. Press the mode key associated with the device you want the channel keys to control.
For example, if you want to assign channel control to your TV only, press TV. All
mode keys blink three times.
The channel keys now always control the device associated with the mode you selected
in this step, whether in TV, CBL, or VCR mode.
Note: In AUX mode, the remote always controls channels for the device assigned to the
AUX key.
Controlling Channels For Different Devices
(Program Code 9 9 7)
1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Press 9 9 7. The CBL key blinks twice.
3. Press SELECT. All mode keys blink three times.
The channel keys now control the device associated with the mode key you select. For
example, in TV mode, the channel keys control the TV, but in CBL mode, the channel
keys control the cable box.
13
Put It Back the Way I Got It
Return specific advanced functions or all advanced functions back to their original
settings. Choose the procedure that fits your needs.
Important: Your cable service provider may have programmed the dual power control
feature for your convenience. Therefore, if you reset the power control, you may need
to program the remote to control the power for the cable box and TV at the same time.
Resetting Mode Keys (Program Code 9 9 2)
You can reprogram the VCR key and the AUX key to operate in their original modes.
1. Press and hold CBL and SELECT until all mode keys blink twice.
2. Press 9 9 2. The CBL key blinks twice.
3. Do one of the following:
• If you are returning the VCR key to its original state, press VCR twice.
• If you are returning the AUX key to its original state, press AUX twice.
All mode keys blink three times.
4. Repeat this procedure if you want to return both keys to their original modes.
Resetting Device Codes and Mode Keys (Program Code 9 7 7)
Follow this procedure to return programmed device codes and mode keys to their
original settings. This procedure erases device codes you programmed. In addition, this
procedure returns all reassigned mode keys to their original operation.
This reset procedure does not reset any changes you made to power, volume, or channel
control.
1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Press 9 7 7. All mode keys blink three times. Then, after a few seconds the CBL key
blinks twice.
Resetting Power, Volume, and Channel Control (Program Code 9 8 0)
Follow this procedure to return power, volume, and channel control to their original
settings. This reset procedure does not reset any device codes you programmed or affect
mode key reassignments.
1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Press 9 8 0. All mode keys blink three times.
Resetting All Changes (Program Code 9 8 1)
Follow this procedure to return the remote completely back to its original settings.
1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Press 9 8 1. All mode keys blink three times. Then, after a few seconds the CBL key
blinks twice.
14
Code Tables
If the remote does not recognize your device, you can find codes for your device by
brand. With combination devices (such as a TV with a built-in DVD player), you have
separate codes for each device component. Therefore, for ease of use, the combination
device codes are listed first. All other code tables are organized by devices assigned to
each mode (CBL, TV, VCR, AUX).
Combination Devices
If you have a combination device, you may need to reassign the AUX key to operate one
of the devices. See Reassign Mode Keys for more information. The following tables
provide some examples of combination devices. If your combination device is not listed,
simply look for the codes for each separate device.
DVD/VCR Combo Codes
Brand
DVD Code
VCR Code
Model
Go Video
Go Video
JVC
RCA
Samsung
Sanyo
2141
2147
2142
2143
2144
2145
2146
2038
2044
2039
2040
2041
2042
2043
DVR5000
DVR4200
HRXVC1U
VC125HF
DVD-V2000
DVW5000
XBV243
Zenith
TV/DVD Combo Codes
Brand
TV Code
DVD Code
Model
Broksonic
RCA
Toshiba
1181
1182
1183
2148
2149
2150
SC975
BD20TF10
MD20FL3
CBL Group: Cable and Satellite Devices
Cable Codes
Satellite Codes
Scientific-Atlanta 0000, 0001, 0002, 0003, 0004,
0005, 0006
Dishnet
Echostar
GE
Proscan
RCA
0013
0014
0012
0012
0012
ABC
GE
Gemini
0010
0010
0011
General Instruments 0010
Hitachi
0010
Jerrold
0010, 0011
0007, 0008*
0009
0010
0010
*Use
or
when testing this code.
Motorola
Pioneer
Proscan
Signature
Starcom
Stargate
0011
0011
15
TV Group: TVs and HDTVs
TV Codes
TV Codes
TV Codes
Admiral
Aiko
Akai
Amtron
Anam
National
1001, 1139, 1159
1014
1002
1034
1003, 1034
GE
1003, 1004, 1006,
1018, 1044, 1045,
1046, 1053, 1072,
1132, 1133, 1134,
1145, 1161
1004, 1005, 1006,
1010, 1017, 1047,
1048, 1049, 1126,
1127, 1137, 1138
Mitsubishi
1004, 1005, 1006,
1017, 1018, 1043,
1067, 1068, 1069,
1102
Montgomery
Ward
Motorola
MTC
1001
Goldstar
1003, 1139
1004, 1005, 1006,
1087
1034
1070
1006, 1060, 1061,
1147, 1166
1003, 1004, 1005,
1006, 1009
1006, 1014
1034
1147, 1166
1079, 1139
1031, 1152
1003, 1045, 1136,
1162
1000, 1003, 1004,
1005, 1006, 1008,
1010, 1017, 1057,
1058, 1063, 1065
1000, 1003, 1004,
1008, 1010, 1017,
1057, 1058, 1063,
1071, 1072, 1073,
1074
1004, 1006, 1075,
1076, 1143, 1147,
1166
1004, 1005, 1006,
1014, 1137
1087
1045
1053, 1145
1004, 1006, 1010,
1077
1003, 1045, 1059,
1078, 1162
1042, 1062
1004, 1006, 1010,
1034, 1042, 1053,
1062, 1079, 1137,
1138
1003, 1004, 1005,
1006, 1007, 1017,
1053, 1080, 1081,
1082, 1083, 1084,
1085, 1105, 1143,
1145, 1148, 1149,
1151, 1155, 1163,
1167, 1170, 1182
AOC
1004, 1005, 1006,
1007, 1140, 1141,
1153
1180
1034
Hallmark
Hitachi
1004, 1006
Multitech
Multivision
NAD
Apex
Audiovox
Bell &
Howell
Broksonic
Carver
1004, 1006, 1010,
1011, 1012, 1050,
1051, 1052, 1109,
1110, 1111, 1112,
1113, 1114, 1115,
1116, 1117, 1118,
1119, 1120, 1121,
1143, 1154, 1166,
1169
1001, 1042, 1062
NEC
1181
1000
1002
1004, 1006, 1008,
1014, 1034, 1062,
1087, 1137, 1160
1004, 1006, 1009
1010, 1011, 1012,
1034
Nikko
Onwa
Optimus
Optonica
Orion
Celebrity
Citizen
Infinity
JBL
JC Penney
1000
1000
Colortyme
Contec/Cony
1004, 1005, 1006,
1008, 1011, 1018,
1044, 1045, 1048,
1049, 1053, 1061,
1072, 1086, 1087,
1104, 1137, 1138,
1145
Panasonic
Philco
Philips
Craig
Crosley
Crown
1034
1000
1034
Curtis Mathes 1000, 1004, 1006,
1013, 1042, 1053,
Jensen
JVC
1004, 1006
1010, 1011, 1012,
1045, 1051, 1054,
1055, 1056, 1128,
1129, 1146, 1168
1002, 1004, 1006
1004, 1006, 1017
1034, 1057, 1058
1062, 1087, 1137,
1160, 1167
Daewoo
1004, 1005, 1006,
1014, 1015, 1016,
1103, 1137, 1151
1004, 1006, 1137
1053
1004, 1122
1002
1002, 1003, 1004,
1006, 1017, 1018
1004, 1006, 1010,
1019, 1020, 1021,
1022, 1023, 1024,
1025, 1026, 1027,
1028, 1029, 1030,
1031, 1032, 1033,
1034, 1035, 1036,
1037, 1038, 1039,
1040, 1042, 1062,
1101, 1137, 1142,
1143, 1152, 1168
Pioneer
Kawasho
Kenwood
Kloss
Novabeam
Daytron
Dimensia
Dumont
Electroband
Electrohome
Portland
KTV
1034, 1059, 1137,
1142
1005
1001
1004, 1006
1000, 1006, 1042,
1053, 1060, 1061,
1062, 1145
1000, 1004, 1006,
1008, 1017, 1057,
1058, 1063, 1064,
1065, 1073, 1106,
1107, 1108
Price Club
Prism
Proscan
Proton
LG
Logik
Luxman
LXI
Emerson
Quasar
Radio Shack
Radio Shack/
Realistic
Magnavox
RCA
Majestic
Marantz
1050, 1066
Megatron
Memorex
1001
1000, 1004, 1006,
Envision
Fisher
1004, 1006
1041, 1042, 1043,
1062, 1144
1040
1034, 1040
1006, 1050
1001, 1005, 1006,
1042, 1062
1004, 1005, 1006,
1017, 1018, 1043,
1067, 1068
Fujitsu
Funai
MGA
Realistic
1042, 1062
16
HDTV Codes
TV Codes
TV Codes
JVC
1175
1179
1178
1174, 1176, 1177
1171
Runco
Sampo
1122
1004, 1006, 1137,
1138
1004, 1005, 1006,
1010, 1013, 1017,
1086, 1087, 1088,
1137, 1138, 1156
Wards
1000, 1001,1004,
1005, 1006, 1017,
1020, 1029, 1040,
1044, 1053, 1057,
1058, 1063, 1064,
1072, 1073, 1079,
1099
1004, 1005, 1006,
1017
1001, 1004, 1122,
1123, 1124, 1125,
1158
Panasonic
Samsung
Sony
Thomson
Toshiba
Samsung
1172, 1173
Yamaha
Zenith
Sansui
Sanyo
1152
1004, 1041, 1042,
1062, 1068, 1089,
1090, 1135, 1144
1004, 1006, 1010,
1020, 1031, 1034,
1040
1000, 1004, 1006,
1011, 1012, 1017,
1040, 1041, 1042,
1043, 1053, 1055,
1060, 1061, 1062,
1091, 1092, 1144,
1145, 1150
Scott
Sears
Sharp
1004, 1006, 1010,
1022, 1025, 1079,
1093, 1094, 1095,
1100, 1137, 1139
Signature
Sony
1001
1002, 1157, 1164,
1165
Soundesign
1004, 1006, 1008,
1034, 1040
Starlite
1034
Sylvania
1000, 1004, 1006,
1008, 1017, 1057,
1058, 1063, 1064,
1065, 1073, 1096,
1131
Symphonic
Tandy
1029, 1034, 1150
1139
Tatung
1003
Technics
Techwood
Teknika
1045
1004, 1006, 1045
1000, 1001, 1004,
1005, 1006, 1008,
1010, 1011, 1012,
1014, 1034, 1040,
1064, 1087, 1136,
1137, 1162
Telecaption
Toshiba
1097
1042, 1060, 1061,
1062, 1087, 1091,
1097, 1098, 1130,
1131, 1183
Totevision
Universal
Vidikron
1137
1044, 1072
1000
17
VCR Group: VCR, PVR, CD, and DVD Devices
VCR Codes
VCR Codes
VCR Codes
Kenwood
2005, 2006, 2007,
2012, 2013, 2031,
2033
2024
2010, 2014
2010
2024
2010
2000, 2014, 2015,
2028
2000, 2005, 2006,
2007, 2012, 2013,
2014
Realistic
2007, 2009, 2010,
2011, 2014, 2015,
2016, 2017, 2019,
2020, 2021, 2027,
2035, 2047
2034
2028
2004, 2009, 2011,
2041
2006, 2031, 2033
2007, 2009, 2016,
2042
2008, 2011, 2026
2007, 2010, 2014,
2016, 2020, 2021,
2022, 2023, 2029
2019, 2027, 2035,
2045, 2047
2003, 2023, 2024
2035, 2047
2014, 2024, 2034
2003
2014, 2029
2000, 2014, 2015,
2017, 2026
2017
2007
2010
2031
2017, 2031
2014
2010, 2014, 2017
2011, 2020, 2022,
2026, 2032
2009, 2010
2009
2005, 2006, 2011,
2012
2005, 2006, 2011,
2012, 2032
2000, 2009, 2010,
2011, 2014, 2016,
2017, 2019, 2022,
2023, 2024, 2027,
2029, 2035, 2047
Admiral
Aiko
Aiwa
Akai
2035, 2047
2018
2017
2002, 2003, 2004,
2031, 2032
2010
2007
KLH
Kodak
LG
Logik
LXI
Magnavox
Ricoh
Runco
Samsung
Audiovox
Bell &
Howell
Broksonic
Calix
Canon
Capehart
Carver
CCE
2008
2010
2014, 2015
2030
2000
Sansui
Sanyo
Marantz
Scott
Sears
Matsushita
Memorex
2014
2018, 2024
2007, 2009, 2010,
2014, 2016, 2017,
2028, 2035, 2047
2019, 2026, 2032
2022, 2023, 2029
2019, 2022, 2023,
2026, 2032, 2033
2035, 2047
Citizen
2009, 2010, 2011,
2012, 2013, 2018,
2045
2005
2009, 2010, 2016,
2024
Sharp
MGA
Minolta
Mitsubishi
Colortyme
Craig
Shintom
Signature
Singer
Sony
STS
Sylvania
Curtis Mathes 2005, 2009, 2012,
2013, 2014, 2015,
Montgomery
Ward
Motorola
MTC
2025, 2046
2011, 2017, 2018,
2030, 2045
2030
2025, 2046
2010, 2019
2002, 2008, 2010,
2011, 2014, 2017,
2019, 2026, 2032
2007, 2016, 2020,
2021
2003, 2014
2017
2017
2014, 2035, 2047
2009
2009, 2012, 2017,
2024
2005, 2006, 2007,
2012, 2013, 2031,
2033
2010
2009
2014
2010, 2035, 2047
2027
Daewoo
Symphonic
Tandy
Tashiko
Tatung
Multitech
Daytron
Dimensia
Electrohome
Emerson
NEC
Teac
Nikko
Noblex
Technics
Teknika
Toshiba
Fisher
Olympus
Optimus
Optonica
Panasonic
Pentax
Fuji
Totevision
Unitech
Vector
Research
Video
Concepts
Wards
Funai
Garrard
GE
2014, 2015
2012, 2022, 2023,
2029
2001, 2009, 2014,
2015, 2025, 2046
2038, 2044
2005, 2010, 2013
2017
Pentex
Research
Philco
Philips
Pioneer
Portland
Proscan
Quasar
Radio Shack
Radio Shack/
Realistic
2013
Go Video
Goldstar
Gradiente
Harman
Kardon
Harwood
Hitachi
2014, 2015
2000, 2014, 2027
2006, 2022, 2033
2012, 2030, 2045
2001, 2025, 2046
2014, 2015
2000, 2005
2024
2022, 2023, 2029,
2031
2005, 2006, 2007,
2008, 2009, 2010,
2014, 2015, 2022,
2023, 2024, 2029
XR-1000
Yamaha
2014, 2017, 2024
2005, 2006, 2007,
2013, 2031
2003, 2028, 2034,
2043
2010, 2027, 2047
JC Penney
2007, 2009, 2010,
2014, 2015, 2016,
2017, 2019, 2020,
2021, 2027, 2035
Zenith
Jensen
JVC
2022, 2023, 2031
Radix
RCA
2010
2005, 2006, 2007,
2013, 2031, 2033,
2039
2001, 2002, 2009,
2014, 2022, 2023,
2025, 2029, 2040,
2046
18
PVR Codes
DVD Codes
DVD Codes
Onkyo
Oritron
2100
2114
Echostar
Philips
2037
2036
Aiwa
Alpine
Apex
2057, 2070
2071
2068, 2069, 2072,
2073
Panasonic
2061, 2101, 2102,
2103, 2104, 2105,
2106
2051, 2067, 2107
2053, 2108, 2109,
2110, 2111
2048, 2112
2113, 2114
2048, 2049*, 2115,
2143, 2149
2116
2117, 2118, 2119,
2144
CD Codes
BOSE
2140
2074, 2148
2075
2076
2077
2078, 2079, 2080,
2081
2082, 2083
2084
ADC
Aiwa
Akai
Emerson
Fisher
GE
Hitachi
JVC
Kenwood
Marantz
Mitsubishi
Nakamichi
NEC
Onkyo
Panasonic
Pioneer
RCA
Sanyo
Sears
Sherwood
Sony
Teac
2166
2151
2167
2152
2153
2169
2154
2155
2156
2158
2170
2172
2157
2159
2160
2161
2162
2175
2168
2173
2163
2174
2164
2171
2165
Philips
Pioneer
Broksonic
Clarion
Classic
Daewoo
Denon
Proscan
Qwestar
RCA
Emerson
Fisher
Funai
GE
Go Video
GPX
Sampo
Samsung
2083
2048, 2085*, 2086
2141, 2147
2087
2056, 2088, 2089,
2090, 2091
2050, 2058, 2092,
2142
2093
2059, 2060
2051, 2094
2095
2096
2052
Sansui
Sanyo
Sharp
Sherwood
Sony
2120
2062, 2121, 2145
2122, 2123
2124
2054, 2063, 2064,
2125, 2126, 2127,
2128, 2129
2083
2130
2131
2132
2055, 2065, 2133,
2134, 2135, 2150
Hitachi
JVC
Kenwood
Konka
Magnavox
Memorex
Mintek
Mitsubishi
NAD
Nakamichi
Norcent
Sylvania
Teac
Technics
Techwood
Toshiba
Technics
Toshiba
Yamaha
2082
2097
2098, 2099
Yamaha
Zenith
2136, 2137, 2138
2066, 2139, 2146
*Use
when testing this code.
AUX Group: Receivers, Amplifiers, and Tuners
AUX Device Codes
AUX Device Codes
AUX Device Codes
RCA
3007
3000
3019
3008, 3009, 3018
3016, 3017
3000, 3012*
3010, 3011,
Aiwa
3000, 3001, 3002,
3003, 3004, 3014,
3020
3000
3000, 3013
Kenwood
Linn
Maganvox
Marantz
Onkyo
Panasonic
Philips
Pioneer
3006
3000
3000
3000
3015
3016, 3017
3000
Sansui
Sherwood
Sony
Technics
Wards
Carver
Harman
Kardon
JBL
JVC
3013
3005
Yamaha
3012*
3012*
*Use
or
when testing this code.
19
FCC Compliance
United States FCC Compliance
Note: This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against such interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and
used in accordance with the instructions, it may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment OFF and
ON, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the cable company or an experienced radio/television technician for help.
Any changes or modifications not expressly approved by Scientific-Atlanta could void the user’s authority to
operate the equipment.
The information shown in the FCC Declaration of Conformity paragraph below is a requirement of the FCC and is
intended to supply you with information regarding the FCC approval of this device. The phone numbers listed are
for FCC-related questions only and not intended for questions regarding the connection or operation for this device.
Please contact your cable service provider for any questions you may have regarding the operation or installation
of this device.
FCC Declaration of Conformity
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) the
device may not cause harmful interference, and 2) the device must accept any interference received, including
interference that may cause undesired operation.
AT8400 AllTouch Remote Control
Scientific-Atlanta, Inc.
5030 Sugarloaf Parkway
Lawrenceville, Georgia 30044 USA
Telephone: 770-236-1077
Canada EMI Regulation
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada.
© 2003 Scientific-Atlanta, Inc. All rights reserved. Scientific-Atlanta, the Scientific-Atlanta logo, Explorer, and
AllTouch are registered trademarks and AT8400 is a trademark of Scientific-Atlanta, Inc. Other trademarks
mentioned are property of their respective owners. Product and service availability subject to change without notice.
Scientific-Atlanta, Inc.
5030 Sugarloaf Parkway
P.O. Box 465447
Lawrenceville, GA 30042
September 2003
749219 Rev D
|