Sanyo Camcorder VCC 6592P User Guide

INSTRUCTION MANUAL  
BEDIENUNGSANLEITUNG  
MANUEL D’INSTRUCTIONS  
VCC-6592P  
VCC-6594P  
COLOUR CCD camera  
CCD-Farbkamera  
Caméra CCD COULEUR  
CCD  
About this manual  
A propos de ce manuel  
• Avant d’installer et d’utiliser la caméra, veuillez lire ce manuel  
attentivement. Gardez-le à portée de main pour toute référence  
ultérieure.  
• Before installing and using the camera, please read this manual  
carefully. Be sure to keep it handy for later reference.  
• This manual gives basic connections and operating instructions for 2  
PAL models (VCC-6592P, 6594P).  
• Ce manuel couvre les branchements et instructions pour l’utilisation  
de base pour 2 modèles de format PAL (VCC-6592P et 6594P).  
Über diese Bedienungsanleitung  
• Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der Kamera  
zuerst diese Bedienungsanleitung sorgfältig durch und bewahren Sie  
sie zum späteren Nachschlagen auf.  
2
PAL  
VCC-6592P, 6594P  
• In dieser Anleitung finden Sie die Anschlüsse und die Grundbedienung  
für 2 PAL-Modelle (VCC-6592P und 6594P)  
 
Depending on the conditions of use, installation and environment,  
please be sure to make the appropriate settings and adjustments. If you  
need help with installation and/or settings, please consult your dealer.  
FEATURES  
Built-in interline transfer method 1/3" CCD, approx. 470,000  
picture elements  
CONTENTS  
Equipped with a DSP (Digital Signal Processor) function  
Horizontal resolution, more than 520 TV lines  
High sensitivity, minimum required illumination is 0.3 lux (F1.2,  
AGC HI position)  
PRECAUTIONS........................................................................................ 2  
PARTS NAMES........................................................................................ 3  
CONCERNING AUTO-IRIS LENSES......................................................... 6  
MOUNTING THE LENS........................................................................... 7  
CONNECTIONS....................................................................................... 9  
SETTINGS...............................................................................................1.2  
TROUBLESHOOTING.............................................................................1. 8  
SPECIFICATIONS....................................................................................1. 9  
Two types of backlight compensation functions (multi-spot  
photometry and center focus photometry)  
Low smear, anti-blooming, low lag, no burning and no geometric  
distortion using the CCD solid state image device.  
100% solid state components giving excellent immunity to shock  
and vibration  
Not subject to interference from magnetic or electrostatic fields  
Power supply: 24 V AC operation (VCC-6594P)  
12 V DC operation (VCC-6592P)  
ACCESSORIES  
1 Lens iris plug (4-pin)..................................................................1 pc.  
2 Clamping core A: VCC-6594P...................................................2 pc.  
VCC-6592P...................................................3 pc.  
3 Clamping core B: VCC-6594P...................................................1 pc.  
VCC-6592P...................................................2 pc.  
1
2
3
English  
1
 
PRECAUTIONS  
In case of problem  
Protect from humidity and dust  
Do not use the camera if smoke or a strange odour comes from the  
unit, or if it seems not to function correctly. Disconnect the power  
cord immediately, and consult your dealer (or a Sanyo Authorized  
Service Centre).  
To prevent damages to the camera, do not install it where there is  
greasy smoke or steam, where the dampness may get too high, or  
where there is a lot of dust.  
Protect from high temperatures  
Do not open or modify  
Do not install close to stoves, or other heat generating devices, such  
as spotlights, etc., or where it could be subject to direct sunlight, as  
that could cause deformation, discoloration or other damages.  
Do not open the cabinet, as it may be dangerous and cause damage  
to the unit. For internal settings and repairs, consult your dealer (or a  
Sanyo Authorized Service Centre).  
Be careful when installing close to the ceiling, in a kitchen or boiler  
room, as the temperature may raise to high levels.  
Do not put objects inside the unit  
Install where the temperature range will stay between –10˚C and  
50˚C.  
(no condensation)  
Make sure that no metal objects or flammable substance get inside  
the camera. If used with a foreign object inside, it could cause a fire,  
short-circuits or damages.  
If water or a liquid gets inside the camera, disconnect the power cord  
immediately, and consult your dealer (or a Sanyo Authorized Service  
Centre). Be careful to protect the camera from rain, sea water, etc.  
Cleaning  
Dirt can be removed from the cabinet by wiping it with a soft  
cloth. To remove stains, wipe with a soft cloth moistened with a  
soft detergent solution and wrung dry, then wipe dry with dry  
soft cloth.  
Be careful when handling the unit  
To prevent damages, do not drop the camera or subject it to strong  
shock or vibration.  
Do not use benzine, thinner or other chemical product on the  
cabinet, as that may cause deformation and paint peeling.  
Before using a chemical cloth, make sure to read all  
Install away from electric or magnetic fields  
accompanying instructions. Make sure that no plastic or rubber  
material comes in contact with the cabinet for a long period of  
time, as that may cause damage or paint peeling.  
If installed close to a TV, radio transmitter, magnet, electric motor,  
transformer, audio speakers the magnetic field they generate will  
distort the image.  
 
2
English  
PARTS NAMES  
1 Video output connector (VIDEO OUT: BNC type)  
(VCC-6592P)  
Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector.  
3
2 Power input terminal  
4
5
VCC-6592P: 12 V DC input terminal (12 V DC, GND)  
VCC-6594P: 24 V AC input terminal (AC 24 V, AC 24 V, GND)  
1
2
3 Y/C OUT connector (4 pin)  
Separate Y (luminance) and C (chroma) signals are output from this terminal.  
A better picture quality is obtained if the monitor or VCR is connected to this connector.  
1
2
1 Y signal ground  
2 C signal ground  
3 Y signal: 1.0 Vp-p, 75 ohms, unbalanced, negative sync  
4
3
4 C signal: 0.3 Vp-p, 75 ohms, unbalanced  
4 Power indicator (POWER)  
(VCC-6594P)  
Comes on when the power to the camera is on.  
5 External sync composite video signal input connector  
(VBS IN: BNC type)  
4
1
6
Connect to this connector the synchronizing signal output from a synchronizing signal device or the composite  
signal of a video distributor.  
2
6 Line phase adjustment volume (LINE PHASE) (VCC-6594P only)  
When using two cameras or more, the image on the monitor may roll vertically when switching sources. This  
rolling can be minimized by turning this volume.  
English  
3
 
PARTS NAMES  
7 Lens mount cap  
The cap is installed to protect the lens mount section.  
Remove the lens mount cap before installing a lens (sold separately).  
8 Flange-back adjustment screw (FLANGE BACK ADJ.)  
9 Flange-back lock screw (FLANGE BACK LOCK)  
F Camera installation bracket  
9
7
F
8
2
2
The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the  
longer screws and install the shorter screws on the opposite side to seal the openings.  
3
1
CAUTION:  
When installing the camera support, select a location that can support the total weight of the  
camera and accessories.  
1
1 Shorter screws: M3 x 4  
2 Longer screws: M3 x 6  
3 Camera mounting screw  
hole: 1/4"-20 UNC  
 
4
English  
PARTS NAMES  
G Lens iris output connector (LENS)  
This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens.  
H
H Camera setup section (under the cover)  
G
These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However,  
if due to installation conditions or environment the settings may need to be modified for best results (see  
"SETTINGS"). To access the controls, remove the cover fixing screw, then remove the cover.  
NOTE: When using a 1/2 or 2/3 inch C mount VIDEO (with EE internal amplifier) auto-iris type lens, set the  
A.I. LENS switch to the VIDEO position.  
English  
5
 
CONCERNING AUTO-IRIS LENSES  
DC type auto-iris lens  
VR301  
A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is  
referred to as DC type coil lens or DC type non-amplifier lens.  
(Set the A.I. LENS switch to the DC position.)  
DC  
VIDEO  
VIDEO type auto-iris lens  
A. I.  
LENS  
A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is  
referred to as EE amplifier type lens.  
ALC and LEVEL volume level controls are available on the lens for iris adjustments.  
(Set the A.I. LENS switch to the VIDEO position.)  
Compatible auto-iris lenses  
1/3 inch Sanyo DC type lens  
VCL-CS8LY: Standard angle, f= 8 mm  
VCL-CS4LY: Wide angle, f= 4 mm  
VIDEO type lens  
Standard angle, f= 9 mm  
Telephoto angle, f= 12 mm  
VCL-CS2LY: Ultra-wide angle, f= 2.8 mm  
Greater telephoto angle, f= 16 mm  
If using a VIDEO type auto-iris lens  
Set the ALC and LEVEL controls on the lens to adjust the iris. Normally the ALC volume should be turned  
all the way to Av (Average).  
Depending on the type of lens used, the lens may not perform properly. In such a case, adjust the LEVEL  
volume on the lens casing to correct.  
 
6
English  
MOUNTING THE LENS  
Please use a DC type auto-iris lens (sold separately).  
1
Check the lens mount  
Do not use a lens if the length “L” is more than 5 mm. That may damage the  
camera and prevent proper installation.  
C mount type lens  
2
L
1
2
Remove the lens mount cap from the camera.  
Install the auto-iris lens.  
CS mount type lens  
Carefully align the lens mount with the camera opening, then turn the lens slowly to install it.  
C mount type lens  
3
To allow for flange-back adjustment, install the C-mount adaptor (option) on the lens mount, then carefully  
align the lens mount with the camera opening and turn the lens slowly to install it.  
2
3
Connect the lens plug to the lens iris output connector (LENS) on the side of the camera.  
CS mount  
type lens  
When using lenses from other makers, the plug shape may not correspond to the terminal on the camera.  
In such a case, remove the original plug and using a soldering iron, connect the supplied lens iris plug  
according to the diagram. (Refer to page 8.)  
NOTE: When using an auto-iris lens, the supplied clamping core B must be installed on the lens wire, in  
order to prevent electromagnetic interference to the other devices connected.  
English  
7
 
MOUNTING THE LENS  
Rewiring the lens cable in the lens iris plug  
1
2
Prepare the lens cable.  
1
2
Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire.  
Install the lens iris plug.  
Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close  
the plug cover.  
Pin layout  
DC type lenses  
VIDEO type lenses  
+12 V DC (50 mA max.)  
Brake coil (–)  
Brake coil (+)  
Drive coil (+)  
Drive coil (–)  
1
2
3
4
2
4
1
3
2
4
1
3
Not used  
Video output (1.0 Vp-p, high impedance)  
Ground (for video signal and DC power)  
Flange-back adjustment  
If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of  
focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the  
flange-back position as described below.  
2, 3  
1
2
3
4
Using a + screwdriver, loosen the FLANGE BACK LOCK screw (M2:+).  
Set the zoom lens to the maximum telephoto position, set the focus using the focus ring on the lens.  
Set the zoom lens to the maximum wide angle position, set the focus using the FLANGE BACK ADJ. screw.  
ADJ.  
LOCK  
3
1
Repeat steps 2 and 3, until the image stays in focus when changing from a telephoto shot to a wide angle shot.  
When the setting is complete, tighten the FLANGE BACK LOCK screw.  
4
 
8
English  
CONNECTIONS  
(VCC-6592P only)  
1
(A)  
(A)  
2A  
(A)  
2A  
12 V DC  
+
2
(Video signal connections)  
: VIDEO IN  
12 V DC connection  
(B)  
3
2A  
Push to insert the cable  
: VIDEO OUT  
12 V DC input  
3
Insert the plug of this power cord into a wall outlet.  
Basic connection for monitoring or recording  
The peripheral devices (VCR, monitor, lens, etc.) and cables are  
The POWER indicator (A) will light. Adjust the picture on the  
monitor using the Brightness and Contrast controls etc.  
sold separately.  
Coaxial cable type and maximum length  
1
2
Make the video signal connection between the camera and  
the monitor or time lapse VCR.  
Cable type RG-59U (3C-2V), 250 m maximum.  
Cable type RG-6U (5C-2V), 500 m maximum.  
Cable type RG-11U (7C-2V), 600 m maximum.  
Use a commercially available 12 V DC adaptor.  
Connect an DC 12 V power source to the 12 V DC input terminal  
on the back of the camera.  
CAUTION:  
2A: When using this unit, the supplied clamping core (A or B) must be  
installed on the power cord and BNC cable, in order to prevent  
electromagnetic interference to the other devices connected.  
The RG-59U type cable should not be run through electrical  
conduits or through the air.  
Using CCTV/Video-grade coaxial cable.  
English  
9
 
CONNECTIONS  
(VCC-6592P only)  
1
(A)  
(A)  
2A  
12 V DC  
+
2
(Video signal connections)  
: VIDEO IN  
12 V DC connection  
(B)  
3
2A  
Push to insert the cable  
: VIDEO OUT  
12 V DC input  
3
The POWER indicator (A) will light. Adjust the picture on the  
monitor using the Brightness and Contrast controls.  
Connections to the camera Y/C OUT connector  
The peripheral devices (VCR, monitor, lens, etc.) and cables are  
CAUTION:  
sold separately.  
Please use a monitor with a Y/C or S-VIDEO input terminal, or a  
time lapse VCR with a S-VIDEO input terminal.  
1
2
Using a coaxial cable (twin type, 75 ohms), connect the Y/C  
OUT connector from the camera to the S-VIDEO input  
terminal on the monitor or time lapse VCR.  
Use a Mini-DIN (round type, 4-pin) plug to connect to the Y/C  
connector.  
Never use a coaxial cable longer that 10 metres to connect the  
camera to the S-VIDEO input terminal.  
Use a commercially available 12 V DC adaptor.  
Connect an DC 12 V power source to the 12 V DC input terminal  
on the back of the camera.  
2A: When using this unit, the supplied clamping core (A or B) must be  
installed on the power cord and BNC cable, in order to prevent  
electromagnetic interference to the other devices connected.  
 
10  
English  
CONNECTIONS  
(VCC-6594P only)  
1
(A)  
3
2A  
AC 24 V connection  
Push to insert the cable  
AC 24 V  
2
(Video signal connections)  
: VIDEO IN  
2A  
GND  
~ ~  
: VIDEO OUT  
3
Insert the plug of this power cord into a wall outlet.  
Basic connection for monitoring or recording  
The peripheral devices (VCR, monitor, lens, etc.), AC adaptor  
The POWER indicator (A) will light. Adjust the picture on the  
monitor using the Brightness and Contrast controls etc.  
and cables are sold separately.  
Coaxial cable type and maximum length  
1
2
Make the video signal connection between the camera and  
the monitor or time lapse VCR.  
Cable type RG-59U (3C-2V), 250 m maximum.  
Cable type RG-6U (5C-2V), 500 m maximum.  
Cable type RG-11U (7C-2V), 600 m maximum.  
Use a commercially available 24 V AC adaptor.  
Connect an AC 24 V power source to the AC 24 V input terminal  
on the back of the camera.  
CAUTION:  
2A: When using this unit, the supplied clamping core (A) must be  
installed on the power cord and BNC cable, in order to prevent  
electromagnetic interference to the other devices connected.  
The RG-59U type cable should not be run through electrical  
conduits or through the air.  
Using CCTV/Video-grade coaxial cable.  
English  
11  
 
SETTINGS  
(VCC-6592P only)  
The illustration shows the factory default settings for the switches in the camera setup section.  
The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be  
sure to read the Note which is given.  
6
7
-a  
9
Control name  
Position  
1/50 sec.  
High speed electronic shutter (ES)/  
Electronic iris (EI) setting  
1
R
B
VR301  
VR302  
VR303  
ON  
Auto gain control setting (HI/NORM)  
HI  
2
3
DC  
VIDEO  
Aperture compensation setting  
(SHRP/NORM)  
SHRP  
1
2
3
4
5
6
7
8
9
10  
A. I.  
LENS  
Backlight compensation setting (BLC)  
(MULT/OFF)  
OFF  
OFF  
4
5
6
Backlight compensation setting (BLC)  
(CENT/OFF)  
1 2 3 4 5 6 7 8  
White balance switch (MANU/ATW) and  
colour (R or B) adjustment volume  
ATW  
External sync setting (SC-PHASE1)  
External sync horizontal adjustment (H)  
Auto-iris lens setting (A.I. LENS), see page 6  
Lens iris level adjustment volume  
0
7
7-a  
8
ES/EI  
2
GAIN APER  
BLC  
WB SC-PHASE 1  
adjustable  
DC  
1
3
HI SHRP MULT CENT MANU 180  
90  
adjustable  
9
MSB  
LSB NORM NORM OFF  
OFF ATW  
0
0
* The sticker on the inside of cover.  
 
12  
English  
SETTINGS  
(VCC-6594P only)  
The illustration shows the factory default settings for the switches in the camera setup section.  
The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be  
sure to read the Note which is given.  
6
9
Control name  
Position  
1/50 sec.  
High speed electronic shutter (ES)/  
Electronic iris (EI) setting  
1
R
B
VR301  
VR302  
VR303  
ON  
Auto gain control setting (HI/NORM)  
HI  
2
3
DC  
VIDEO  
1
2
3
4
5
6
7
8
9
10  
Aperture compensation setting  
(SHRP/NORM)  
SHRP  
A. I.  
LENS  
Backlight compensation setting (BLC)  
(MULT/OFF)  
OFF  
OFF  
4
5
6
1 2 3 4 5 6 7 8  
Backlight compensation setting (BLC)  
(CENT/OFF)  
White balance switch (MANU/ATW) and  
colour (R or B) adjustment volume  
ATW  
ES/EI  
2
GAIN APER  
HI SHRP MULT CENT MANU  
BLC  
WB SYNC NC  
Syncronisation (SYNC) setting (INT/LL)  
Auto-iris lens setting (A.I. LENS), see page 6  
Lens iris level adjustment volume  
INT  
DC  
1
3
LL  
7
8
9
adjustable  
MSB  
LSB NORM NORM OFF  
OFF ATW  
INT  
* The sticker on the inside of cover.  
English  
13  
 
SETTINGS  
Table A (switch 1 ~ 3)  
Electronic shutter settings and electronic iris  
settings  
1
2
3
4
5
6
7
8
1/50(AI) 1/120 1/500 1/1000 1/2000 1/4000 1/10000 EI  
When all of these switches are down, electronic shutter (1/50 sec or  
auto iris setting) is enabled. The electronic shutter can be set to one  
of 7 speeds as shown in Table A.  
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
(Unit: sec.)  
Furthermore, when all switches are up, electronic iris setting is  
enabled.  
Automatic Gain Control (AGC) setting  
Notes on the electronic shutter:  
The automatic gain control can be turned HI or NORM  
using the AGC switch 4 in the camera setup section.  
Using the high speed electronic shutter indoors with low lighting,  
will give darker pictures. In such a case, add some lights to make  
sure the lighting is sufficient. If the lighting is very bright, pay  
attention to the light angle in order to avoid or minimize the  
smear phenomenon effect.  
HI: Auto gain control fuction on (+6 dB)  
NORM: Auto gain control (normal gain)  
4
Use a manual or fixed iris lens and set the lens aperture to the  
shortest F stop. Set the switch (1 – 3) to the up position.  
Note: In the AGC switch position HI, noise may be noticed in dark  
places of dimly lit objects. In the AGC switch position NORM,  
the noise will be reduced, but the sensitivity will also be  
reduced to half in this case.  
The electronic iris is suitable for normal indoor use. When the  
switch (1 – 3) is set to the up position, do not use an auto-iris lens.  
If used under fluorescent light, the image may flicker. In such a  
case, change to incandescent lighting or set the switch (1 – 3) to  
the down position and use an auto-iris lens.  
Aperture  
The initial setting for switch 5 is up (SHRP) so that the  
contours of the object are emphasized. However, if the  
contours of the object are already emphasized more  
If conditions are outside the electronic iris operation range or  
more than the maximum illumination, it will cause saturation of  
the CCD. In that case, use a manual iris lens.  
than required, set switch 5 to the down (NOR) position.  
5
 
14  
English  
SETTINGS  
(MULTI mode: 64 sections)  
Backlight compensation setting  
This camera has two different backlight  
compensation functions: Normally backlight  
compensation switch 6 (MULT) and 7 (CENT)  
are set to the down (OFF) position. Change  
the backlight compensation switch settings  
depending on the conditions.  
6
7
MULT mode: Use this position when applying backlight  
compensation to the whole of the screen.  
(CENT mode)  
CENT mode: Use this position when applying backlight  
compensation to only the central portion of the  
screen.  
Note:  
If switches 6 and 7 are set to the up (ON) position at the same  
time, the MULT setting will have priority.  
When MULT mode is set, scenes with no backlighting may appear  
extremely dark and the object may appear over-exposed. If this  
happens, set to CENT mode.  
If using a VIDEO type auto-iris lens  
The ALC volume on the lens should be turned all the way to Av  
(Average).  
If the backlight compensation function does not compensate  
properly for the conditions, set using the LEVEL volume on the  
lens.  
English  
15  
 
SETTINGS  
White balance adjustment  
External sync adjustment (VBS) (VCC-6592P only)  
Normally the switch 8 (WB) is set to the down (ATW: auto white  
balance) position and the white balance is adjusted automatically. If a  
manual white balance adjustment is necessary, follow the steps below.  
1
2
Connect the VBS signal output for the other camera to the VBS  
IN connector at the rear of this camera.  
If the signals are not synchronized, change the sub-carrier (SC-P1)  
switches as follows.  
Set the switch 8 (WB) to the up (M: manual) position, then adjust the  
colour.  
Setting  
9-pin  
OFF (down)  
OFF  
10-pin  
OFF  
Turn RED (VR302) to set the red ratio and/or BLUE (VR303) to set  
the blue ratio.  
Default  
Set to 90˚ counterclockwise  
Set to 180˚ counterclockwise  
Set to 270˚ counterclockwise  
ON (up)  
OFF  
ON  
R
B
ON  
ON  
VR302  
VR303  
8
9
10  
H-P  
Note:  
Synchronization settings  
The sub-carrier switches let you make broad adjustments to the  
sub-carrier phase. If finer adjustments are required, contact the  
place of purchase.  
The default setting is internal synchronization (INT). You can  
change the power supply synchronization by moving switch 9  
to the up (LL) position. Refer to “Line phase adjustment”  
for details.  
The type and length of the cable which is connected to the VBS  
connector may cause the horizontal synchronization being out of  
phase. If this happens, adjust VR304 (H-P: horizontal sync).  
 
16  
English  
SETTINGS  
Lens iris adjustment  
Line phase adjustment (VCC-6594P only)  
If using a DC type auto-iris lens, you will need to set the LEVEL  
(VR301) volume when shooting in the conditions described below.  
When using a camera switcher to connect 2 cameras or more to one  
monitor, there may be a vertical roll of the images when switched. In  
such a case, set as described below.  
1
2
Set the switch 9 (SYNC) to the up (LL) position.  
VR301  
Switch the display on the monitor from camera 1 to camera 2.  
Adjust the LINE PHASE volume on camera 2 until the vertical roll  
of the image stops.  
L (counterclockwise): To decrease the contrast  
If more than two cameras are used, please repeat this procedure  
for all the cameras.  
H (clockwise): To increase the contrast  
If shooting simultaneously in a dark room and through a bright  
window.  
If the subject background is extremely bright or dark.  
If the brightness of the picture on the monitor is not correct.  
9
CAUTION:  
If the vertical roll cannot be corrected by setting the LINE PHASE  
volume on camera 2, try setting the LINE PHASE volume on camera  
1. If it still cannot be corrected, please check that the polarity of the  
power cords of all connected devices is correct.  
English  
17  
 
TROUBLESHOOTING  
Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please  
consult your dealer or a Sanyo Authorized Service Centre.  
No picture on the monitor screen  
Is the power turned on to all connected devices? Is the voltage correct?  
Are all the signal connecting cables correctly connected?  
Is the lighting sufficient?  
Has the lens cap been removed?  
Is the lens type (DC or VIDEO) correctly selected?  
Depending on the type of lens, the A. I. LENS switch must be set accordingly.  
Is the iris control correctly set?  
The picture is not clear  
Is the monitor correctly adjusted?  
Is the flange-back position correctly set?  
Is the lens focus correctly adjusted?  
Are the lens surfaces clean?  
If there is dust or finger prints on the lens, the image quality will deteriorate. To clean the lens use a soft cloth or a commercially available lens  
cleaning set.  
SERVICE  
This camera is a precision instruments and if treated with care, will provide years of satisfactory performance. However, in the event of a problem,  
the owner is advised not to attempt to make repairs or open the cabinet. Servicing should always be referred to your dealer or Sanyo Authorized  
Service Centre.  
 
18  
English  
SPECIFICATIONS  
Camera:  
Scanning system  
Environmental conditions  
Power supply  
: PAL standard  
: Temperature: –10˚C ~ +50˚C  
(625 TV lines, 25 frames/sec.)  
Humidity: less than 90% (no condensation)  
Interlace  
Image device  
Picture elements  
Effective picture elements  
Synchronizing system  
: PLL 2:1 interlace  
: 1/3 inch solid state image device CCD  
: 795 (H) x 596 (V)  
: 752 (H) x 582 (V)  
: Internal sync, External sync automatic  
switchable (VCC-6592P only)  
Internal sync, Line lock manually switchable  
(VCC-6594P only)  
: 520 TV lines horizontally, 400 TV lines  
vertically  
: 1.0 Vp-p/75 ohms, composite  
: Y: Video; 0.7 Vp-p + sync; 0.3 Vp-p/75 ohms  
C: Burst; 0.3 Vp-p/75 ohms (VCC-6592P only)  
: 12 – 15 V DC (VCC-6592P)  
24 V AC, 50 Hz (VCC-6594P)  
Power consumption  
: VCC-6592P: Approx. 2.7 W  
(with auto iris lens)  
Approx. 2.0 W  
(without auto iris lens)  
VCC-6594P: Approx. 2.8 W  
(with auto iris lens)  
Approx. 2.1 W  
(without auto iris lens)  
: Approx. 310 g (without lens)  
Resolution  
Weight  
Video output level  
Y/C signal outputs  
Video S/N ratio  
: More than 48 dB  
: Approx. 0.3 lux with a F 1.2 lens (AGC, HI)  
Approx. 0.6 lux with a F 1.2 lens (AGC, NORM)  
Minimum required  
illumination  
(incandescent lighting)  
Backlight compensation  
: Manual MULT/CENT/OFF switching (Active  
when using an auto-iris lens)  
Iris function  
: AI/EI selectable by switches (Electronic  
shutter)  
Electronic iris range  
Electronic shutter  
: 0.6 lux to 50,000 lux (F 1.2 lens)  
: 7 speeds, selectable by switches:  
(1/50, 1/120, 1/500, 1/1000, 1/2000,  
1/4000, 1/10000 sec.)  
Flange-back  
White balance  
Lens mount  
AGC  
: 12.5 mm 0.5 mm  
: ATW/Manual switching  
: CS mount  
: HI/NORM  
English  
19  
 
SPECIFICATIONS  
Dimensions  
56  
56  
109  
100  
0.5  
45  
45  
11  
1/4”–20 UNC  
28  
28  
12.6  
22.4  
(VCC-6592P)  
(VCC-6594P)  
Features and specifications are subject to change without prior notice or obligations.  
 
20  
English  

Quantum Wheelchair INFMANU4169 User Guide
Radio Shack Telephone ET 894 User Guide
RCA Universal Remote RCU800 User Guide
Rio Grande Games Board Games 5th Avenue User Guide
RocketFish Network Card RF NBACDC User Guide
Rowenta Iron 1103897124 User Guide
Royal Sovereign Binding Machine RBM 1200 User Guide
Samson Portable Multimedia Player MD13 User Guide
Samsung Microwave Oven SMH6140BB User Guide
Seiko Watch Cal 5J22 User Guide