Ryobi Thermometer E49IR01 User Guide

Length (  
) Measurement:  
Fig. 4  
SPECIFICATIONS  
Press the Measure button (D) to measure length (  
) (J).  
Ø4 in.  
@24 in.  
After two seconds the unit will display the result of the length  
Laser Certifications ................................................. <1mW, 630-660 nm  
Display Auto Off ....................................................................... 3 minutes  
Temperatrue Range......................................................... -22ºF to 518º F  
INFRARED THERMOMETER SPECIFICATIONS:  
measurement (F).  
Ø1 in.  
@6 in.  
Area (  
) Measurement:  
OPERATOR’S MANUAL  
Press the ( X/=) button (G) until the (  
) (J) symbol is displayed.  
3-IN-1 INFRARED THERMOMETER,  
SONIC DISTANCE MEASURER,  
LASER POINTER  
Press the Measure button (D) to take first length measurement.  
The unit will display the result of the length measurement.  
Reposition unit and take second length measurement.  
Accuracy ................................................................-22º F to 30º F ± 5° F  
32° F to 518° F± 4° F  
Distance to Spot Ratio ...................................................................... 6 : 1  
Ø101.6 mm  
@ 609.6 mm  
Ø25.4 mm  
Operating Temperature..................................................... 32º F to 104º F  
Temperature Update:................................................................5 seconds  
DISTANCE MEASURER SPECIFICATIONS:  
After two seconds the unit will display the result of the area  
E49IR01  
@ 152.4 mm  
measurement.  
Volume (  
) Measurement:  
Press the ( X/= ) button (G) until the (  
) (J) symbol is displayed.  
WARNING!  
Measurement Range.............................................................. 1 ft to 30 ft  
Accuracy of Distance ....................................................... ±0.5% ± 1 digit  
Press the Measure button (D) to take first length measure ment.  
The unit will display the result of the length measurement.  
Reposition unit and take second length measurement.  
The unit will display the result of the area measurement.  
Reposition unit and take third length measurement.  
Read and understand all instructions. Failure to follow all instructions  
listed below may result in electric shock, fire and/or serious injury.  
OPERATION  
WARRANTY  
WARNING:  
The 3-in-1 Infrared Thermometer, Sonic Distance Measure, Laser Point  
takes non-contact temperature measurements and distance measure-  
mentsforelectricians,facilitymaintenancepersonnel,HVACapplications,  
automotive applications, and more.  
Use of controls or adjustments or performance other than those  
specified herein may result in hazardous radiation exposure.  
LIMITED TWO YEAR WARRANTY AND 30 DAY EXCHANGE POLICY  
After two seconds the unit will display the result of the volume  
30-DAY EXCHANGE POLICY: During the first 30 days after date of  
purchasing this product, you may either request service under this war-  
ranty or you may exchange it by returning it with proof of purchase and  
all original equipment packaged with the original product to the dealer  
from which it was purchased. The replacement product will be covered  
by the limited warranty for the balance of the two year period from the  
date of the original purchase.  
measurement.  
The unit will turn off in 60 seconds if there are no further operations or  
no key is pressed.  
Complies with CFR 1040.10  
INSTALLING THE BATTERY  
E49IR01  
& 1040.11  
See Figure 1.  
DANGER • DANGER • PELIGRO  
LASER RADIATION : AVOID DIRECT EYE EXPOSURE  
RAYONNEMENT LASER : ÉVITER LE CONTACT OCULAIRE DIRECT  
RADIACIÓN LÁSER: EVITE LA EXPOSICIÓN DIRECTA DE LOS OJOS  
A 9 volt battery (included) must be installed before using the unit.  
Fig. 1  
Slide the battery cover off.  
MAXIMUM OUTPUT: <1.0 mW • WAVELENGTH : 630-660nm • CLASS II LAS ER PRODUCT  
PUISSANCE MAX. : <1.0 mW • LONGUEUR D’ONDE : 650nm • PRODUIT LA SER DE CLASSE II  
POTENCIA MÁX. <1.0 mW • LONG. ONDA: 650nm • APARATO LÁSER CLASE II  
C
Attach the battery terminals to their connectors on the unit.  
LIMITED TWO YEAR WARRANTY. This product is warranted against all  
defectsinworkmanshipormaterialsforaperiodoftwoyearsfromthedate  
of purchase. The warranty on any accessories for this product, excluding  
batteries, is limited to 90 days from the date the accessory is purchased.  
To obtain warranty service, call Customer Service at 1-800-525-2579 for  
warranty return instructions. The product must be properly packaged and  
returned with all equipment that was included with the original product.  
When you request warranty service, you must also present proof of pur-  
chase documentation, which includes the date of purchase (for example,  
a receipt or a bill of sale). Defective products returned within the warranty  
period will be repaired or replaced, at our option, free of charge, within  
ninety (90) days or less. The cost of shipping the product to us is your  
responsibility. This warranty only covers defects arising under normal us-  
age and does not cover any malfunction, failure or defects resulting from  
misuse, abuse, neglect, alteration, modification orunauthorized repairs. It  
applies only to the original purchaser at retail, and may not be transferred.  
One World Technologies, Inc. makes no warranties, representations or  
promises as to the quality or performance of this product other than  
those specifically stated in this warranty. Any implied warranties granted  
under state law, including warranties of merchantability or fitness for a  
particular purpose, are limited to two years from the date of purchase.  
One World Technologies, Inc. is not responsible for direct, indirect, or  
incidental damages Some states do not allow limitations on how long  
an implied warranty lasts, or the exclusion or limitation of incidental or  
consequential damages, so the above limitations and exclusions may not  
apply to you. This warranty gives you specific legal rights, and you may  
also have other rights which vary from state to state.  
Close the battery compartment by sliding the cover into place until it  
snaps closed.  
Made in China Fabriqué en Chine Fabricado en China  
A
TAKING TEMPERATURE READINGS  
See Figures 2 - 4.  
Avoid Exposure. Radiation is emitted from this aperture.  
Éviter toute exposition. Le rayonnement est émis de cette ouvetrure.  
Evite la exposición. Se emite radiación a través de esta abertura.  
To obtain the most accurate readings, follow these instructions:  
Complies with / Convient aux pièces / Cumple con partes 21 CFRparts 1040.10 & 1040.11  
A - 9V battery (Pile de 9 V, batería de 9  
V)  
Temperature readings can only be measured on a target surface.  
Avoid direct eye exposure when using the laser and do not project  
the laser beam directly into the eyes of others. Serious eye injury  
could result.  
Surfaces covered by frost, dirt, or other material should be cleaned  
before taking reading.  
B - Battery cover (couvercle du compar-  
timent de la batterie, tapa de la bat-  
ería)  
C - Battery terminals (bornes de batterie,  
terminales de la batería)  
B
For highly reflective surfaces, such as mirrors or windows, place a  
piece of paper or tape on area where reading will be taken.  
Do not remove or deface any product labels. Removing product  
labels increases the risk of exposure to laser radiation.  
To take a temperature reading:  
Do not place the instrument in a position that may cause anyone  
to stare into the laser beam intentionally or unintentionally. Serious  
eye injury could result.  
Press Power button (E) to turn on unit.  
Press Mode button (F) to set unit to Infrared Mode, shown as IR (M)  
on LCD display (I).  
Do not operate the laser around children or allow children to oper-  
Fig. 2  
A - Laser beam (faisceau laser , rayo  
láser )  
B
Point the unit toward the area you wish to read and press the Measure  
button (D). See Figure 4 to determine distance to spot ratio for  
accuracy of reading.  
ate the tool. Serious eye injury could result.  
A
C
B - Sonic beam (faisceau sonique, rayo  
sónico)  
Do not use for medical evaluations or to measure body temperature.  
This product is meant for household use only.  
C - Infrared beam (faisceau à infrarouge,  
rayo infrarrojo)  
NOTE:TheLaserpointer(A)willcomeonwheneverMeasurebutton(D)  
is pressed. The Laser pointer (A) indicates the center of the circular  
area being scanned for reference only.  
Do not use this product as a precision thermometer.  
I
D
S
C
Q
U
.
.
23  
Do not operate the instrument in combustible areas such as in the  
ftm  
D - Measure button (bouton « measure  
» (mesure), botón de medición)  
E - Power button (bouton « power »  
(marche/arrêt), botón de encendido)  
F - Mode button (bouton « mode »  
(mode), botón modo)  
G - (X/=) button [bouton « (X/=) », botón  
(X/=)]  
H - ºC/Fº (units) button [bouton « ºC/Fº »  
(Unités), botón ºC/Fº (unidades)]  
I - LCD display (afficheur ACL, pantalla  
de LCD)  
ºF  
8
presence of flammable liquids, gasses, or dust.  
8
8
8
The unit will take reading (L).  
HOLD  
IR  
Always ensure the laser beam is aimed at a surface without re-  
flective properties. Shiny reflective materials are not suitable for laser  
use.  
The surface temperature readings (L) are shown in LCD display.  
When the Measure button (D) is released, the laser will turn off. The  
HOLD (O) icon will stay on until you turn unit off or another reading is  
taken.  
H
G
E
The laser shall be used and maintained in accordance with the  
C/F  
manufacturer’s instructions.  
X/=  
To switch between Celsius to Fahrenheit units, press the ºC/Fº (units)  
button (H).  
Mode  
 Never aim the beam at a perso or object other tha the target  
F
surface.  
The unit will turn off in in 60 seconds if there is no operation or no key  
is pressed.  
This product should not be used without the battery cap in-  
stalled.  
TAKING DISTANCE MEASUREMENTS  
See Figures 2 - 3.  
Handle the instrument with care. Treat it as you would any other  
optical device such as a camera or binoculars.  
Fig. 3  
To obtain the most accurate readings, follow these instruc-  
Avoid exposing the instrument to shock, continuous vibration, or  
extreme hot or cold temperatures. Damage to the product and/or  
serious injury to the user could result.  
tions:  
The LCD display shows the measurement for distance (L)  
J - Length, area, volume icon [icône «  
length » (longueur), « area » (aire) et  
« volume » (volume), Ícono de longi-  
tud, área y volumen]  
K
J
from the device to the target surface, with icons for calculations length  
(
), area (  
) and volume (  
) (J).  
ONE WORLD TECHNOLOGIES, INC.  
Press Power button (E) to turn on unit.  
K - Sonic icon (icône « sonic » (so-  
nique), ícono sónico)  
23  
SQ.  
CU.  
1428 Pearman Dairy Road, Anderson, SC 29625  
ftm  
Press Mode button (F) to set unit to Sonic mode (K), shown as  
on LCD display.  
L
Phone 1-800-525-2579  
L - Reading (lecture, medición)  
M- Infrared icon (icône « infrared » (in-  
frarouge), Ícono infrarrojo)  
32.0°F  
Measurements are calculated from the rear of the tool.  
N - Laser icon (icône « laser » (laser),  
Ícono láser)  
To switch back and forth from ft/in. to cm/m, press the  
ºC/Fº (Units) button (H).  
M
Ryobi® is a registered trademark of Ryobi Limited used under license.  
IR  
HOLD  
O - Hold icon (icône « hold » (retenue),  
ícono mantener)  
P - Battery charge icon (icône « battery  
charge » (charge des piles), ícono  
del cargador de la batería)  
987000-814  
8-31-09 (ReV:01)  
N
P
O
 

Radio Shack Range 15 1974 User Guide
Radio Shack TV Converter Box 15 1214 User Guide
RCA Stereo System RP 7701K9 User Guide
Salton Kitchen Grill SG 1207 User Guide
Samsung Cell Phone E2350B User Guide
Samsung Range FER300SB User Guide
Sanus Systems TV Video Accessories SFV265B User Guide
Sears Battery Charger 20071232 User Guide
SECO LARM USA Door SK 1123 FQ User Guide
Seiko Printer FB 900 User Guide