A / V
D I S T R I B U T I O N
&
C O N T R O L
S Y S T E M S
CA6.4
Instruction Manual
6-Zone, 4-Source
Central Controller/Amplifier
TUNER
CD
S
O
U
R
C
E
TAPE
AUX
•ON / OFF
•VOLUME
•SOURCE
SOURCE
REMOTE SENSOR
6
Z
O
N
E
—
4
S
O
U
R
C
E
C
E
N
T
R
A
L
C
O
N
T
R
O
L
L
E
R
/
A
M
P
L
I
F
I
E
R
ON
1
2
3
4
5
6
OFF
POWER
ZONE
CA 6.4
2. Introduction
Congratulations on your recent purchase of the Russound CA6.4 multi-room controller. This six-zone, four-
source, multi-room controller is an affordable integrated amplifier. The CA6.4 controller is the heart of the system.
Six stereo power amplifiers are built into the Russound CA6.4 allowing simple connections to each speaker in
the system. Each zone is operated by an intuitive easy-to-use keypad. The keypad controls all the functions of the
CA6.4 controller. CA6.4KP keypads have a built-in infra-red receiver used to repeat your source equipment
remote functions back through the CA6.4 controller.
The Russound CA6.4 is built with pride. Fidelity, Reliability and Quality is the primary objective. Russound prod-
ucts are guaranteed to provide years of enjoyment. The CA6.4 is UL listed and CSA approved for your protection
and peace of mind. Please take a moment to fill out the warranty card and return it to Russound.
ZONE 5
Childs Room
3. Possible System Configurations
CASSETTE
ZONE 3
Library
ZONE 4
Guest Room
CD
CD
SOURCE ROOM
Family Room
ZONE 1
Living Room
ZONE 2
Kitchen
ZONE 6
Patio
TUNER
CD
CASSETTE
DSS
TUNER
CD
DSS
(Audio Signal)
CA6.4
Controller
4. Unpacking and Warranty Card
• Carefully unpack the CA6.4 and keep the original carton and packing materials for future moving, shipment or
long-term storage. After opening the box, please check for any visible signs of damage that were not apparent
from the outside of the box. If you do encounter what appears to be concealed damage, please consult your
Russound dealer before proceeding to further unpack or install the unit.
• Make sure to save your sales receipt. Your receipt is extremely important to establish the duration of your limit-
ed Warranty, and for insurance purposes.
• Warranty Card –The serial number appears on the rear panel of this unit near the power cord. Copy the serial
number onto your warranty card and mail it back to Russound / FMP, Inc. 5 Forbes Road Newmarket, New
Hampshire 03857. Be sure to retain a copy and keep it in a safe place.
5. Getting Started
The following information will indicate some tools and materials necessary for a complete installation of the CA6.4:
• 4 twisted pair communication wire (commonly referred to as CAT 5). This wire will be used to connect the
keypads in each zone to the CA6.4 controller. 16 Gauge minimum, 2 conductor CL3 rated wire. (Russound
AW162CL3) This wire is used for direct connection between the CA6.4 and your speakers.
NOTE: CAT5 should not be run more than 100’ or in combination with the CA6.4 LRN. For runs more than
100’ or when using optional CA6.4 LRN please use 8-conductor 20AWG wire shielded.
• A small jewelers flat-head screwdriver.
• A medium sized flat-head screwdriver.
• Wire strippers and cutters.
• Electric drill and a 1/2" x 6 "drill bit.
• A steel-wire fish tape.
3
Additional tools required to complete installation:
• A keyhole saw.
• Electrical junction boxes (6).
• A stud finder.
• A screwdriver (cordless recommended)
• Misc. hand tools, nails & screws.
• Cable staples.
If you have problems or you are not
absolutely comfortable with what you are
doing, consult a professional carpenter,
electrician, or system installer.
6. Basic Planning and Layout Considerations
• Where will the speakers be located ?
• How will the wiring be routed to each location ?
• Where will the keypads be located ?
• Where is the equipment located ?
• Where is the CA6.4 controller going to be located ?
Speaker Wire Length
Gauge of Speaker Wire
10-50 feet . . . . . . . . . . . . . . . . . . . . . . .18 AWG
50-100 feet . . . . . . . . . . . . . . . . . . . . . .16 AWG
100-150 feet . . . . . . . . . . . . . . . . . . . . .14 AWG
Over 150 feet . . . . . . . . . . . . . . . . . . . .12 AWG
Connection Tips
• Disconnect all power cords before connecting to the CA6.4.
• Verify that all connections and polarity are correct.
• Keep all power cords away from all signal cables to prevent noise or humming.
• Choose reliable signal cables / patch cords.
• Label all wires with room location at both ends of the wire.
• Take your time!!! Don't panic about the number of wires; simply connect one at a time.
TUNER
S
CD
TAPE
AUX
O
U
R
C
E
Keypad Zone
Connectors
•
•
•
ON OFF
/
VOLUME
SOURCE
SOURCE
REMOTE SENSOR
Source Inputs
INPUT FROM KEYPADS
CA6.4
CD
NEWMARKET, NH U.S.A.
6
5
4
3
TUNER
TAPE
AUX
R
L
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5
OUTPUT TO 8Ω SPEAKERS
6
5
4
3
IR
IR REMOTE OUTPUT
LINK
4
3
2
1
USE #1 FIRST
IR Link
Emitter Outputs
Speaker Output
Connectors
4
7. Back Panel Connections
7.1 Source Input Connections
• Your source inputs are located at the top left corner of the back panel. Connect each source output, left and
right, using quality signal cables / patch cables. Label each cable the name of your source and the input num-
ber of the CA6.4 you have selected. Repeat until all sources are connected. List them down below.
figure 1 –Input 1 ______________ Input 2 ______________ Input 3 ______________ Input 4 ______________
7.2 Speaker Connections
• Keeping in mind the location of the corresponding keypad, connect your speakers by first removing the connec-
tor. Using wire strippers, strip back 1/8" of the end of the wire. Insert the proper polarity, left + to left +, left- to left-
etc., until all wires are connected in each zone output. Label each wire with the room name and zone number.
Write down the room name to the zone number below. Note: Connect 8 Ohm minimum speakers only.
figure 2 –(Color) Left + _____________ Left - _____________ Right + _____________ Right - _____________
Zone 1 ________________________ Zone 2 ________________________ Zone 3 ________________________
Zone 4 ________________________ Zone 5 ________________________ Zone 6 ________________________
7.3 Connecting The Infra-red Components (diagram on next page)
• In order for your CA 6.4 to transmit the IR signal from the keypads to a source, an emitter must be connected
from the IR outputs marked 1-4. Each of these outputs are wired in series and must be connected in consecu-
tive order. For example, the #1 emitter output must be connected in order for the #2 emitter output to transmit
the IR command.
• Connect each 845 mini-emitter to the source IR output. Refer to the source number you had written down
above figure 1.
Voltage Selector
Switch
2
1
~220-240VAC
~110VAC
6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
S
WARNING : SHOCK HAZARD –
DO NOT OPEN
VOLTAGE FUSE
110V F4A
220-240V F2A
2
1
AVIS : RISQUE DE CHOC
~110VAC
ELECTRIQUE – NES PAS OUVRIR.
~220-240VAC
~50-60Hz
400W
SERIAL #
MADE IN KOREA
AC110/240
Input
Fuse
Holder
5
• Remove the adhesive back and locate the IR receiver on the product you wish to control. Stick
the 845 emitter directly over the source components IR window. The CA6.4 will direct the IR
command to the source component you wish to control.
CD PLAYER
845
EMITTER
• Repeat connections until all emitters match the selected sources.
CASSETTE DECK
7.4 Connecting the IR Link
845
EMITTER
• When two CA6.4 Controllers are to be used in an installation,
TUNER
the IR Link connection is used to pass IR signal between the
REAR OF
CA6.4
two units. Use a 1/8”, mono, phone plug, male to male cable
845
connected from the IR Link on the first CA6.4 Controller to the
EMITTER
IR Link on the second CA6.4. When connected, you may connect
TO OTHER SOURCE
your IR emitters to either unit’s IR Remote Output jacks.
845
EMITTER
1584
DUAL
EMITTER
7.5 Keypad Connections
• Each keypad connection on the back panel corresponds to the room / zone number chosen for your speakers.
Each zone operates independently, so it is very important to connect the keypad to the correct zone keypad
input. Remove the connector and strip 1/8" off each end of the wire insulation. Connect each wire 1 thru 8
using a small jewelers screwdriver. At this point it is not important what color wires connect where, however,
take note of the color of each wire and number indicated on the connector when connected to the back panel.
• Write down the room name to the zone number on next page. Note: the keypad and the speakers in each
room must be hooked to the same zone number. See figures 2 and 3
figure 3
Zone 1 _____________ Zone 2 ______________ Zone 3 _______________
Zone 4 _____________ Zone 5 ______________ Zone 6 _______________
figure 4 –Connector numbers and wire color should be written down below.
Pin 1 ________ Pin 2 ________ Pin 3 _________ Pin 4 _________
Pin 5 ________ Pin 6 ________ Pin 7 _________ Pin 8 _________
8. Keypad Installation
8.1 Installing the KP Keypads
• The best performance is achieved with the keypad away from any direct sunlight. Also consider the conve-
nience when choosing a location.
• Choose a place that is easily seen from the position where a person is most likely to be located.
• Check whether or not you can route the wire to the location you have chosen.
• Purchase retro-fit plastic junction boxes ( min. 20 cubic inches ) and cut in the boxes using a key-hole saw or
sheetrock knife/hand saw.
• Route the wire to the junction box from the CA6.4 location.
• Strip the insulation back 1/8" from each twisted wire. Connect each wire to the correct position 1 thru 8. Refer
to figure 4.
• If you feel uncomfortable cutting into your walls and running wire through the walls, seek help from a profes-
sional installer or an electrician.
• Mount the keypad in the junction box and attach the Decora plate.
• The CA6.4 keypad has source labels for your convenience. Place the label on the keypad keeping the input
number in sequence with the source selected.
• Repeat the above steps until all keypads are installed.
6
8.2 Installing the LRN Keypads
• Connect the CA6.4 LRN’s Interface cable to the 16 pin header
located on the CA6.4 KP Interface. Note the location of the red stripe.
• Mount the keypads into double gang box and
attach the double gang Decora plate.
INTERCONNECT
CABLE
CA6.4 LRN
CA6.4 KP
RED
STRIPE
9. Speaker Installation
• If you are installing in-wall speakers, follow the instructions
provided with your speakers for mounting.
• Connect each speaker wire to the correct polarity (+,-).
-
+
Finally!!!
• Power up by plugging in all power cords and
turning the CA6.4 and sources on.
10. Operation
• Power switch - When the power switch is engaged, the CA6.4 power indicator will be lit an amber color. The
CA6.4 should be left on at all times. The unit will consume very little power unless the zones are on and
active. The unit has a stand-by mode when the zones are inactive.
• The zone indicator will light either red for off or green for on. The zones can only be turned on from the key-
pads. All functions are accessed through the keypad only.
Operating The CA6.4 Keypad
• Power ON / OFF - This knob on the CA6.4 keypad controls all functions except
for the IR management. To turn the unit on, simply turn the control knob clock-
wise. You will feel and hear a click verifying that the unit has been activated.
TUNER
The lights on the keypad will also illuminate to verify the zone is now on. Note
S
O
CD
U
R
- The CA6.4 front panel zone-management lights also informs you which zone
is On or Off.
C
TAPE
E
AUX
• Volume UP / DOWN - Once the unit is on, the knob can be used to adjust the
volume. To adjust the volume up, turn the knob clockwise, and to turn the vol-
ume down, turn counter-clockwise.
•ON / OFF
• Source Selection - By pressing the knob, the zone will scroll through the four
•VOLUME
•SOURCE
sources connected to the CA6.4. The keypad has four lights (LED's) that indicate
the source selected.
SOURCE
REMOTE SENSOR
• IR Source Control - The IR window repeats all source commands from the
source component's remote through the CA6.4 and 845 emitters. Most IR
receivers have a range of 20' at an angle of 60-65 degrees.
7
11. Technical Information:
• Frequency Response: 20 Hz to 20 KHz ( +/- 1 dB )
• 15 Watts RMS / Channel @ 8Ω
• 12 Channels / 6 Stereo Amplifiers
• Total Harmonic Distortion: .1%
• Signal to Noise Ratio: 89 dB min, “A” weighted
• Power Supply: ~110VAC/~220-240VAC 50-60Hz
400W High Current Toroidal
• ETL listed. Conforms to UL Standard UL1492
and CSA Standard C22-2 No. 1-M94
• CE Approved
• Fully Functional Keypad with IR Receiver
Centered at 40 KHz
12. Warranty
The Russound CA6.4 is fully guaranteed for Two (2) years from the date of purchase against all defects in materi-
als and workmanship. During this period Russound will replace any defective parts and correct any defect in
workmanship without charge for either parts or labor. For this warranty to apply, the unit must be installed and
used according to its written instructions. If service is necessary, it must be performed by Russound. The unit must
be returned to Russound at the owners expense and with prior written permission. Accidental damage and ship-
ping damage are not considered defects under the terms of the warranty. Russound assumes no responsibility for
defects resulting from abuse or servicing performed by an agency or person not specifically authorized in writing
by Russound. Damage to or destruction of components due to improper use voids the warranty. In these cases
the repair will be made at the owners expense. To return for repairs, the unit must be shipped to Russound at the
owners expense, along with a note explaining the nature of the service required. Be sure to pack in a corrugated
container with at least 3 inches of resilient material to protect the unit from damage in transit.
Now sit back and let all members of the household enjoy the personalization that the Russound CA6.4
provides. Happy listening!
A
/
V
D
I
S
T
R
I
B
U
T
I
O
N
&
C
O
N
T
R
O
L
S
Y
S
T
E
M
S
5 Forbes Rd. Newmarket, NH 03857
ꢀꢀ603.659.5170 • Fax 603.659.5388
e-mail: [email protected]
Come visit us at:
8
|