Royal Sovereign Laminator RSL2701S User Guide

OWNER'S MANUAL  
RSL-2701U (for CANADA MODEL)  
RSL-2701S (for USA MODEL )  
Read all instructions carefully before use.  
For any Customer Support needs please choose the  
Customer Support tab on www.royalsovereign.com  
Royal Sovereign International Inc.  
 
TABLE TOP LAMINATOR  
1. INTRODUCTION  
Thank you for purchasing the Table Top Laminator. It has been designed and manufactured to provide years of  
continuous service. For high quality lamination, please read this instruction manual thoroughly. This manual will provide  
you with complete operating and maintenance information.  
2. pACkAgE CONTENTS  
Fuse  
Core bolt 4EA  
Film leader board  
Manual  
Core 4EA  
Dust cover  
Sample roll film 2EA  
3
 
3. SAFETy pRECAUTIONS  
Failure to comply with any of the following safety procedures could result in serious injury.  
please read the instructions carefully and keep for future reference.  
1. Only a licensed electrician should install wiring and outlet for the laminator.  
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.  
3. Keep hands and clothing (i.e. Neckties) away from rollers.The rollers have pinch points that can trap body parts  
or  
clothing and cause serious injury.  
4. Keep flammable and wet objects away from the machine.  
5. Place machine on a level surface.  
6. Avoid excessive sunlight, humidity and extreme temperatures.  
7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/or repairing.  
8. Keep out of reach of children.  
9. Only authorized maintenance and service technicians should make repairs.  
10. Do not attempt to laminate items that exceed total recommended material thickness for the unit  
11. When cleaning the machine, don't use flammable sprays or materials.  
12. Do not touch the rollers when hot.  
Do not place any foreign obects inside the laminator.  
13. Do not cover the surface of the machine until the machine has completely cooled.  
14. You can laminate by single film when the switch in the left cover is “O”.  
(Insure the machine drastically cold, press the button in the left cover be “ O ”, then you can laminate by single  
side. It is a damage for the paper to laminate by single side while the rollers up and low are heating all together.)  
- Model applies RSL-2701S only for USA.  
4
 
TABLE TOP LAMINATOR  
4. pARTS  
10  
1. Upper Film  
4. Hot Rollers  
7. Control Panel  
2. Lower Film  
3. Idle Bar  
5. Feed Table  
6. Paper Guide  
9. Power Switch  
8. Tension Knob  
*10. (2701S model only) Single/Double Laminating Switch “O” (on) “I” (off).  
* For Single-side Laminating.  
5
 
5. CONTROL pANEL  
Film Application Temperature  
270 ~310 ˚F  
230 ~270 ˚F  
210 ~230 ˚F  
270 ~310 ˚F  
270-310 F  
230-270 F  
210-230 F  
Film Application Temperature  
230 ~270 ˚F  
Film Application Temperature  
210~230 ˚F  
Increase roller speed  
(1~10 speed settings)  
UP  
Reduce roller speed  
(1~10 speed settings)  
DOWN  
Reverse the rollers to undo jams and correct  
misfed documents  
REVERSE  
Run and stop the machine  
RUN/STOP  
RSL-2701U  
6
 
TABLE TOP LAMINATOR  
Film Application Thickness  
125mic(100~125mic)  
125mic  
* (100~125mic)  
5 mil  
125 mic  
Film Application Thickness  
50~100mic(50~75mic)  
50~100mic  
* (50~75mic)  
2 - 4 mil  
50-100 mic  
Film Application Thickness  
25~38mic(25~38mic)  
25~38mic  
* (25~38mic)  
1 - 1.5 mil  
25-38 mic  
Reduce roller speed  
(1~10 speed settings)  
UP  
Increase roller speed  
(1~10 speed settings)  
DOWN  
Reverse the rollers to undo jams and correct  
misfed documents  
REVERSE  
Run and stop the machine  
RUN/STOP  
* For Single side Laminating.  
RSL-2701S  
7
 
6. FEATURES gUIDE  
1
Power Switch  
Located on the rear of the machine. “I” (on) “0” (off). (Fig. 2)  
2
Cross Cutter  
Used to cut off the laminated web. (Fig. 2)  
3
Feed Guide  
Figure 2  
The feed guide permits alignment of the item(s) to be laminated.  
To position the adjustable guide, loosen the knob, slide it to the  
desired position and tighten the knob to secure the feed guide in  
place. (Fig. 3)  
4
Safety Cover  
Cover + Protect the hot rollers.  
NOTE: If the safety cover is opened, this rollers stop turning.  
Figure 3  
5
5
Film Shaft and Locking Core Adapter  
The film shaft holds the film supply on the machine. The locking  
core holds and locks the film on the shaft to prevent shifting. (Fig.  
4)  
6
Film Tension Adjustment  
Allows the operator to increase or decrease roll film tension. To  
increase the tension turn the knob clockwise and to decrease  
tension turn the knob counterclockwise. (Fig. 5)  
Figure 4  
NOTE: - Excess tension on the top roll feed will cause upward  
curl.  
- Excess tension on the botton roll feed will cause  
downward  
curl.  
6
- Tension should be adjusted until the laminated materials  
exit flat.  
Figure 5  
8
 
TABLE TOP LAMINATOR  
7. FILM LOADINg & ThREADINg  
Figure 6  
1. Slightly slide the upper film shaft to the right and pull it out from  
the machine. (Fig. 7)  
Figure 7  
2. Take both lock core adapters off from the shaft. (Fig. 8)  
Figure 8  
9
 
3. Insert one of the core adapters into the right end of the film  
core. For film with poly-in (adhesive side is inside the web), make  
sure the adhesive side is facing upward. (Fig. 9)  
Figure 9  
4. Insert the film shaft into the roll of film from the right side with  
the copper end last.  
Align and insert the core adapter on the left end of the film  
core. (Fig. 10)  
Figure 10  
5. Center the film on the shaft and lock it in place with the  
locking core adapters. (Fig. 11)  
Figure 11  
6. Carefully return the film shaft back into place. (Fig. 12)  
Figure 12  
10  
 
TABLE TOP LAMINATOR  
LOADINg LOWER ROLL FILM  
1. Repeat steps 1-5 to load the lower roll film.  
2. Once the upper and lower film is on the shaft, pull the film from the top and roll down to the bottom roll to make  
certain that the film is aligned properly. Then tighten the lower locking core screws.  
NOTE: If the film is not aligned properly exposed adhesive will adhere to the rollers and may cause the film to jam.  
FILM ThREADINg / WEBBINg  
1. Set the temperature and speed according to the Recommended  
Temperature and Speed section.  
2. Remove the Front Table.  
3. Pull down the upper film over the Safety Cover to the lower film; align  
Picture 1  
and center the lower film to upper film. (Picture 1)  
4. Rewind the upper film until the film aligns with the Safety Cover.  
5. Thread the film over the Upper Idle Bar and underneath the Safety  
Cover and pull down until it drapes over both upper and lower hot  
rollers. (picture 2)  
6. Carefully pull up the laminate from the lower roll up and drape it over  
top of the upper film (over the top hot roller). (picture 3)  
Picture 2  
Picture 3  
Picture 4  
7. Reinstall the Front Table and close the Safety Cover.  
8. Insert and push the leader board into the hot rollers and press the  
Run button. (picture 4)  
9. Press the Stop button when the leader board has completely exited  
the rear of the laminator.  
10. Use the Cross-Cutter to remove the leader board.  
11. Trim any excess film off of the leader board. The leader board can  
be re-used.  
11  
 
LAMINATINg SINgLE SIDED (RSL-2701S USA Model only)  
Press the switch into the location “SINGLE ”.  
Figure 13  
12  
 
TABLE TOP LAMINATOR  
8. OpERATION INSTRUCTIONS  
1. Turn the laminator ON (I) located on the rear of the machine. (Fig. 2)  
2. Choose appropriate laminating temperature and speed. (Fig. 1)  
3. Do not begin laminating until the blinking light is steady (approximately 8 minutes).  
4. Position the item to be laminated on the feed table.  
5. Press the RUN button. The rollers will begin to turn, and feed the item into the machine.  
6. Insure the machine drastically cold, press the button in the left cover be “ O ”,then you can laminate by upper  
roller for single laminating.(It is a damage for the paper to laminate by single side while the rollers up and low are  
heating all together.)  
- Model applies RSL-2701S only for USA.  
7. The first paper is bad while OPP film laminating, please use a test paper first and then the second paper must  
keep the distance less than 15mm form the front one.  
- Model applies RSL-2701S only for USA.  
8. Stop the laminator when all of the items have completely exited the rear of the machine.  
9. Adjust top + botton roll feed tension until lamination is flat.  
(See film tension adjustment page 8.)  
NOTE: Stand by mode and auto power off mode  
- Stand by mode: If no activity is made within 30 minutes after each use the machine will automatically switch  
into stand by mode. (In stand-by mode the temperature will decrease to 80~90°C and the three  
temperature setting indicators will blink).  
- Auto power off mode: If the machine is in stand by mode and no activity is made for 60 minutes the  
machine will automatically power off.  
- If any activity is made while in stand by or auto power off mode the machine will return to it’s previous  
stage.  
9. MAINTENANCE  
1. Do not apply any cleaning fluids to the rollers certain fluids may cause damage.  
2. Do not clean rollers with sharp or pointed objects.  
3. Use a crepe rubber cleaning block to remove adhesive from rollers. Works best when rollers are hot.  
4. Use a damp cloth with water to clean the body of the machine.  
5. Store machine in a dry clean area.  
13  
 
10.TROUBLE ShOOTINg gUIDE  
Symptom  
Cause  
possible Solution  
1. Check safety cover is  
properlyclosed  
1.Safety cover is opened  
2. Power cord is not plugged in  
3. Front table is not on properly  
4. Machine is not turned on  
Rollers do not operate after the RUN/  
STOP button is pressed  
2. Plug in the power cord  
3. Check installed properly  
4. Turn the machine on  
Roller is not heating  
Poor Lamination  
Call your authorized dealer  
Call your authorized dealer  
1. Adjust film tension  
1. Film tension is unbalanced.  
2. Push idler bar in proper position  
2. Lower idler bar is not located in  
proper position  
3. Follow manufacturers  
recommended temperature and  
speed  
3.Wrong temperature / speed setting  
14  
 
TABLE TOP LAMINATOR  
11. SpECIFICATIONS  
MODEL  
RSL-2701U  
RSL-2701S  
RSL-2701  
RSL-2701S  
RSL-380S  
AC100V 60Hz  
AC220~240V  
50/60Hz  
Power supply  
AC120V 60Hz  
AC 220~240V 50/60Hz  
Power consunmption  
Max laminating width  
Film thickness  
1450W  
1500W  
685mm  
380mm  
3m/min  
25~250mic /1~10mil  
25~125mic/1~5mil  
Max laminating speed  
Ready time  
2.5m/min  
10min  
Heating method  
Driving motor  
Hot Roller  
DC geared motor  
Temperature control  
Speed control  
Digital(micom)  
Digital(10steps)  
Transport type  
Cross cutter  
4Roller  
Yes  
Single  
Hot  
No  
Yes  
No  
Yes  
Yes  
lamination  
Double  
Yes  
Reverse  
Dimensions(w×d×h)  
Unit weight  
Yes  
920×520×320mm  
50kg  
550×520×320mm  
30kg  
15  
 
11. WARRANTy  
Royal Sovereign International warrants the equipment sold is free from defects in material and workmanship for a  
period of One (1) year for Parts and Labor from the date of installation, excluding lamination rollers which are  
warranted for Six (6) months. This warranty is extended only to the original purchaser. This warranty is the only  
warranty made by Royal Sovereign International and cannot be modified or amended. Royal Sovereign’s sole and  
exclusive liability and the customer’s sole and exclusive remedy under this warranty shall be, at Royal Sovereign’s  
option, to repair or replace any such defective part or product. These remedies are only available if Royal  
Sovereign’s examination of the product discloses to Royal Sovereign’s satisfaction that such defects actually exist  
and were not caused by misuse, neglect, attempt to repair, unauthorized alternation or modification, incorrect line  
voltage, fire, accident, flood or other hazard.  
All warranty claims must be filed through the authorized Royal Sovereign dealer or reseller through which the  
equipment was originally purchased. Model, serial number and date of delivery are required for all claims.  
The warranty made herein is in lieu of all other warranties, expressed or implied, including any warranty or  
merchantability or fitness for a particular purpose. Royal Sovereign will not be liable for personal damage or personal  
injury (unless primarily caused by its negligence), loss of profit, or other incidental or consequential damages arising  
out of the use or inability to use this equipment.  
LIMITED WARRANTy  
This warranty specifically does not cover damage to laminating rollers caused by knives, razor blades, or any sharp  
objects or abrasives, or failure caused by adhesives, or damage caused by lifting, tilting or improper use of the  
machine. Warranty repair or replacement by Royal Sovereign or its authorized Reseller(s) does not extend the  
warranty beyond the initial one year period from the date of installation. Unauthorized customer alterations will void  
this warranty.  
RS CANADA INC.  
ROyAL SOVEREIgN INTERNATIONAL INC.  
2 Volvo Drive Rockleigh, NJ 07647 USA  
TEL : +1) 800-397-1025  
1025 Westport Crescent, Mississauga ON L5T 1E8  
TEL : +1) 905-461-1095 FAX : +1) 905-461-1096  
TF: +1) 866 961-6673  
FAX : +1) 201-750-1022  
E-mail : [email protected]  
E-mail : [email protected]  
RS hOLLAND B.V.  
Industrieweg 6K, 4104AR, Culemborg, The Netherlands  
Tel: +31 (0)345 473 097  
Fax: 31 (0)345 519 811  
RS INTERNATIONAL AUSTRALIA pTy. LTD.  
30 Prime Drive, Seven Hills, NSW 2147, Australia  
TEL : +61) 2-9674-2127  
FAX : +61) 2-9674-2027  
E-mail : [email protected]  
16  
 

RCA TV Mount MAF80BK User Guide
RCA VCR VR609HF User Guide
Realistic Scanner 20 25 User Guide
Reebok Fitness Treadmill ACD 4 User Guide
Ryobi Drill D50VSR User Guide
Samsung DVR SVS 5R User Guide
Samsung Home Security System SSA S1000 User Guide
Samsung MP3 Player YP K5JZBY User Guide
Samsung TV Mount WMN4655MD User Guide
Sears Cultivator 3162926 User Guide