Roper Clothes Dryer RED4100S User Guide

®
Electric Dryer  
PRODUCT MODEL NUMBERS  
OVERALL DIMENSIONS  
RED4100S  
RED4400S  
RES6745P  
RES6745R  
RES7745R  
REX3514P  
REX3514R  
REX3614P  
REX5634R  
REX6634R  
22¾"  
(57.8cm)  
15¼"  
(38.74cm)  
43³⁄₈"  
43³⁄₈"  
(110cm)  
(110cm)  
Electrical: A four-wire or three-wire, single phase,  
120/240-volt, 60 Hz, AC-only, electrical supply (or  
120/208-volt electrical supply, if specified on the  
serial/rating plate) is required on a separate 30 amp  
circuit, fused on both sides of the line. Use 10  
gauge solid copper wire. A time-delay fuse or circuit  
breaker is recommended.  
*27¾"  
*26"  
(66cm)  
(70.5cm)  
29"  
29"  
(73.66cm)  
(73.66cm)  
B
A
Exhaust venting: Exhaust your dryer to the  
outside. Four-inch diameter vent is required. Rigid  
or flexible metal exhaust vent must be used. Do not  
use plastic or metal foil vent. Exhaust outlet hood  
must be at least 12 inches from the ground or any  
object that may be in the path of the exhaust.  
22¾"  
(57.8cm)  
43³⁄₈"  
43³⁄₈"  
(110cm)  
(110cm)  
13¾"  
(34.9cm)  
*27¾"  
*27¾"  
(70.5cm)  
(70.5cm)  
29"  
29"  
(73.66cm)  
(73.66cm)  
C
D
A. Small opening side-swing door  
B. Large opening side-swing door  
C. Wide opening side-swing door  
D. Wide opening hamper door  
* Most installations require a  
minimum 5¹⁄₂" (14 cm)  
clearance behind the dryer for  
the exhaust vent with elbow.  
RECESSED AREA AND CLOSET INSTALLATION  
3"  
(7.6 cm)  
14" max.  
(35.6cm)  
48 in. 2  
(310 cm2 )  
18"  
(45.7 cm)  
For closet installation with a  
door, minimum ventilation  
openings in the top and bottom  
of the door are required.  
Louvered doors with equivalent  
air openings are acceptable.  
24 in.2  
3"  
(7.6 cm)  
(155 cm2 )  
0"*  
(0 cm)  
27¾"  
(70.5 cm) (14 cm)  
5½"  
29"  
(73.66 cm)  
0"*  
(0 cm)  
0"*  
(0 cm)  
A. Recessed area  
B
C
B. Side view - closet or confined area  
C. Closet door with vents  
A
EXHAUST VENTING  
*Additional spacing recommended  
Recommended hood styles  
Angled hood style is  
acceptable.  
B
Number of  
90° turns  
or elbows  
Type of  
vent  
Box or  
Louvered  
hoods  
Angled  
hoods  
4"  
(10.2 cm)  
A
0
1
2
3
4
Rigid metal  
64 ft (20 m)  
36 ft (11 m)  
58 ft (17.7 m)  
28 ft (8.5 m)  
Flexible metal  
2.5"  
4"  
(6.4 cm)  
Rigid metal  
Flexible metal  
54 ft (16.5 m)  
31 ft (9.4 m)  
48 ft (14.6 m)  
23 ft (7 m)  
(10.2 cm)  
4"  
(10.2 cm)  
Rigid metal  
Flexible metal  
44 ft (13.4 m) 38 ft (11.6 m)  
27 ft (8.2 m) 19 ft (5.8 m)  
A. Louvered hood style  
B. Box hood style  
Rigid metal  
Flexible metal  
35 ft (10.7 m) 29 ft (8.8 m)  
25 ft (7.6 m)  
17 ft (5.2 m)  
Rigid metal  
Flexible metal  
27 ft (8.2 m)  
23 ft (7 m)  
21 ft (6.4 m)  
15 ft (4.6 m)  
Select the route that will provide the straightest and most direct path  
outdoors. Plan the installation to use the fewest number of elbows and turns.  
Avoid making 90° turns.  
Do not use vent runs longer than specified in vent length chart.  
Determine the number of elbows you will need.  
NOTE: Side and bottom exhaust installations have a 90° turn  
inside the dryer. To determine maximum exhaust length, add one  
90° turn to the chart.  
Because Whirlpool Corporation policy includes a continuous commitment to improve  
our products, we reserve the right to change materials and specifications without notice.  
Dimensions are for planning purposes only. For complete details, see Installation  
Instructions packed with product. Specifications subject to change without notice.  
Ref. 8577187  
08-03-06  
 

PYLE Audio Stereo Receiver PLMD8 User Guide
Radio Shack PDAs Smartphones 65 773 User Guide
Remington Styling Iron hairsetter User Guide
Rosewill Network Card RCAD 11001 User Guide
Samsung Computer Drive HX MU025DC User Guide
Samsung Laptop NP270E5EK01JM User Guide
Samsung Printer ML 4550 User Guide
Samsung Printer SCX 5x30 User Guide
Samsung Projection Television SP50L6HD User Guide
Schumacher Battery Charger 1275A PE User Guide