Rolls Home Theater Server RM65 User Guide

LIMITED WARRANTY  
This product is warranted to the original consumer purchaser to be free from  
defects in materials and workmanship under normal installation, use and service for a  
period of one (1) year from the date of purchase as shown on the purchaser’s receipt.  
The obligation of Rolls Corporation under this warranty shall be limited to repair  
or replacement (at our option), during the warranty period of any part which proves  
defective in material or workmanship under normal installation, use and service, provided  
the product is returned to Rolls Corporation, TRANSPORTATION CHARGES PRE-  
PAID. Products returned to us or to an authorized Service Center must be accompanied by  
a copy of the purchase receipt. In the absence of such purchase receipt, the warranty  
period shall be one (1) year from the date of manufacture.  
RM65 HEXMIX  
6 x 4 Audio Mixer  
This warranty shall be invalid if the product is damaged as a result of deface-  
ment, misuse, abuse, neglect, accident, destruction or alteration of the serial number,  
improper electrical voltages or currents, repair, alteration or maintenance by any person or  
party other than our own service facility or an authorized Service Center, or any use  
violative of instructions furnished by us.  
FX  
FX  
MONITOR BASS TREBLE PAN  
MONITOR BASS TREBLE PAN  
VOLUME  
VOLUME  
SEND  
VOLUME  
VOLUME  
SEND  
CLIP  
CLIP  
CLIP  
CLIP  
CLIP  
CLIP  
0
10 -  
-
+
L
R 0  
10  
0
10 -  
+
-
+
L
R 0  
10  
+
FX  
SEND  
FX  
SEND  
MONITOR BASS TREBLE PAN  
MONITOR BASS TREBLE PAN  
This one-year warranty is in lieu of all expressed warranties, obligations or  
liabilities. ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES,  
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MER-  
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE  
LIMITED IN DURATION TO THE ONE YEAR DURATION OF THIS WRITTEN  
LIMITED WARRANTY. Some states do not allow limitations on how long an implied  
warranty lasts, so the above limitation may not apply to you.  
0
10 -  
+
-
+
L
R 0  
10  
0
10 -  
+
-
+
L
R 0  
10  
FX  
MONITOR BASS TREBLE PAN  
VOLUME  
VOLUME  
SEND  
MASTER VOLUME  
EFFECTS  
RETURN  
+17  
LEFT  
RIGHT  
0
10  
-
+
-
+
L
R 0  
10  
+8  
0
FX  
SEND  
MONITOR BASS TREBLE PAN  
P
-4  
PWR  
Professional  
Audio Mixer  
-13  
0
10  
-
+
-
+
L
R 0  
10  
IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL, INCIDENTAL  
OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER  
WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. Some states do not allow  
the exclusion or limitation of special, incidental or consequential damages so the above  
limitation or exclusion may not apply to you. This warranty gives you specific legal  
rights, and you may also have other rights which vary from state to state.  
RM65  
FEATURES  
• 6 XLR and 1/4” Inputs  
• Individual 36 V Phantom Power  
• Clip LEDs on each channel  
• Input Trim, Monitor, FX Send and Pan on each channel  
Treble & Bass control on each channel  
• FX Return, may be used as an additional input  
• Stereo Aux Bus Input  
ROLLS CORPORATION  
SALT LAKE CITY, UTAH  
7/01  
OWNERS MANUAL  
 
SPECIFICATIONS  
PAN: Adjusts the amount of relative signal to the Right, Left or both Main Out  
jacks.  
FX SEND: Controls the amount of signal (post-volume control) that is sent for that  
channel to the FX Send jack.  
Input Impedance:  
600 W balanced  
50K W unbalanced (1/4")  
50 W TRS Balanced  
-15 dBV XLR 600 W  
+18 dBV 1/4"  
Output Impedance:  
Max Input Level:  
MASTER CONTROLS  
FX RETURN: Adjusts the amount of signal coming back into the FX Return jack.  
MASTER VOLUME, RIGHT - LEFT: Controls the amount of signal sent out the  
main Right and Left Output jacks, and sets the overall signal level except for the  
Monitor Send jack.  
Phase Shift:  
< 10 deg. 20 Hz - 20 kHz  
36 V DC  
Phantom Power:  
Input Connectors:  
Outputs:  
XLR and 1/4"  
1/4" main balanced +17 dB max  
1/4" monitor +17 dB max  
1/4" FX send  
REAR PANEL  
CHANNEL 2  
CHANNEL 1  
SERIAL NUMBER  
CHANNEL 6  
CHANNEL 5  
CHANNEL 4  
CHANNEL 3  
MIC  
MODEL RM65  
MIC  
MIC  
MIC  
MIC  
MIC  
65-  
LEFT  
OUT  
RIGHT MONITOR  
OUT OUT  
FX  
RETURN  
FX  
SEND  
AUX  
BUSS IN  
TRIM LINE  
TRIM LINE  
TRIM LINE  
TRIM LINE  
TRIM LINE  
TRIM LINE  
C
US  
PHANTOM  
POWER  
Max Gain:  
(Mains)  
(Monitor)  
60 dB mic  
120 VAC  
50/60 Hz 15 VA  
WARNING  
:
DO NOT EXPOSE THIS EQUIPMENT TO RAIN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE BACK.  
RISQUE DE CHOC NE PAS ENLEVER  
-
MADE IN U.S.A.  
26 dB line  
OR MOISTURE.  
NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
55 dB  
1 - 6 CHANNEL MIC INPUTS: XLR input connectors for mic or line level signals.  
1 - 6 CHANNEL LINE INPUTS: 1/4input connectors for line level signals.  
TRIM: Adjusts the amount of input signal from the mic and line input jacks.  
PHANTOM POWER: 6 switches for turning on the microphone phantom power for  
the XLR inputs, and are numbered for the channel they are assigned to. DOWN is  
on, UP is off.  
AUX BUS IN: 1/4TRS stereo input to the main mix bus, and may be used as an  
auxiliary stereo input for joining two RM65s together.  
FX SEND: 1/4unbalanced jack for sending the signals assigned by each  
channels FX Send control out to external effects.  
FX RETURN: 1/4unbalanced jack for inputting signals from external effects  
devices.  
MONITOR OUT: 1/4unbalanced jack for sending signals assigned by each  
channels monitor output control to an auxiliary amplifier or monitoring system.  
RIGHT and LEFT OUTPUT: 1/4TRS balanced jacks to be used as the units  
main outputs.  
Tone controls:  
Max S/N Ratio:  
THD  
20 dB treb, bass cut/boost, 400 Hz center  
106 dB  
< .003%  
IMD (SMPTE)  
CMRR  
< .003%  
52 dB  
Power  
120 VAC 50-60 Hz, 15 W  
7 lbs (3KG)  
Weight:  
Size:  
19" x 1.75" x 6.5" (48cm x 4.5cm x 17cm)  
NOTES:___________________________________________________________  
USING PHANTOM POWER  
Phantom power is a means of powering condenser microphones through the  
microphone cable.The RM65 has individually switchable 36 volts of phantom  
power for each of its 6 channels through the XLR jacks. The DIP switches on the  
rear of the unit are for switching the power on and off. When the little switch tab is  
down, the power is on. The number on the switch corresponds to the channel that  
is receiving the power. If phantom power is not needed, it should be switched off  
to avoid possible damage to a microphone, or degraded sound quality.  
5
2
 
OPERATION  
The RM65 is ideal for small combo groups where a small number of instruments  
and microphones need to be mixed together. Refer to Figure 1 for an example of  
how to connect the inputs and outputs of your RM65. Connect microphones to  
balanced XLR cables and to the XLR inputs. If any of these microphones are  
condenser microphones, they will require phantom power.To turn on the phantom  
power for an individual channel, set the phantom power switch for that channel to  
the ON (down) position. Instruments may be played into a microphone which is  
connected as indicated above, or if you have active pickups in your instrument  
simply connect the output of your instrument to an RM65 Line Input as the  
acoustic guitar is shown in Figure 1.  
Electric guitars and basses normally are connected to an instrument amplifier or  
preamplifier. Amplifiers may have microphones placed in front of the speaker, or if  
the amp has a line level output (check with the amplifiers owners manual) - it may  
also be connected to the mixer directly. Keyboards and sound modules are  
connected directly to the RM65s line inputs as shown.  
CHANNEL 6  
CHANNEL 5  
CHANNEL 4  
CHANNEL 3  
MIC  
CHANNEL 2  
CHANNEL 1  
SERIAL NUMBER  
65-  
MODEL RM65  
MIC  
MIC  
MIC  
MIC  
MIC  
LEFT  
OUT  
RIGHT MONITOR  
OUT OUT  
FX  
FX  
AUX  
BUSS IN  
TRIM LINE  
TRIM LINE  
TRIM LINE  
TRIM LINE  
TRIM LINE  
TRIM LINE  
RETURN SEND  
PHANTOM  
POWER  
C
US  
120 VAC  
50/60 Hz 15 VA  
WARNING  
:
DO NOT EXPOSE THIS EQUIPMENT TO RAIN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE BACK.  
RISQUE DE CHOC NE PAS ENLEVER  
-
MADE IN U.S.A.  
To use the FX Loop, connect a 1/4unbalanced cable to the FX Send and to the  
Input on your signal processor or effects device. Connect the Output of the signal  
processor or effects device to the RM65 FX Return jack. The level of the effect will  
be controlled by the settings on the channelsFX Sends and by the Output Level  
of your effects device, The overall level of the effect will be controlled by the FX  
Return level on the front of the RM65.  
OR MOISTURE.  
NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
VOLUME  
MONITOR AMPLIFIER  
PWR  
CLIP  
CLIP  
R
A
1
7
0
To use the Monitor feature of the RM65, connect the Monitor Out jack to a monitor  
amplifier via a 1/4unbalanced cable. Each channels monitor level is controlled by  
that channels Monitor level setting. Be aware that the RM65 has no master  
monitor level, so you will need to set the overall monitor level with the monitor  
amplifier and the Monitor Levels of each channel.  
VOLUME  
1
VOLUME  
1
MAINS AMPLIFIER  
1
5
30 100  
1
5
30 100  
0
10  
0
10  
PROTECT  
WATTS  
WATTS  
Connect the Right and Left Main Outputs to the main amplifier(s) and make sure  
the amplifier is the correct rating for the speakers. If you are operating in mono,  
use either the Right or Left Output.  
The RM65 may also be used for recording. Connect microphones, instruments,  
and effects to the inputs as described above - the connect the Right and Left  
outputs to your recording device and set the levels accordingly.  
Figure 1  
3
4
 

RedMax Trimmer BT280 User Guide
Ricoh Printer Printer Reference User Guide
RTS Network Card TIF 2000A User Guide
Samsung Air Conditioner MH18VP2 09 User Guide
Samsung Home Theater System 20051111115925328 User Guide
Samsung Microwave Oven M1716 User Guide
Sanus Systems Indoor Furnishings HTB4 User Guide
Sanyo Projector PDG DHT100L User Guide
Sanyo Radio M9708L User Guide
Sennheiser Battery Charger L 1032 User Guide