Roksan Audio Stereo Amplifier M series 1 User Guide

C a s p i a n  
Mseries -1  
Integrated Amplifier  
U S E R M A N U A L  
R O K S A N A U D I O L I M I T E D  
6 NORTHFIELD INDUSTRIAL ESTATE  
BERESFORD AVENUE  
MIDDLESEX HA0 1NW  
ALPERTON  
ENGLAND  
T E L .  
F A X .  
+ 4 4 ( 0 ) 2 0 8 9 0 0 6 8 0 1  
+ 4 4 ( 0 ) 2 0 8 9 0 0 6 8 0 2  
+ 4 4 ( 0 ) 2 0 8 9 0 0 0 7 3 4  
w w w . r o k sa n . c o . u k  
e ma i l in f o @ r o k s a n . c o . u k  
 
CAUTIONS  
C a s p i a n Integrated Amplifier  
AC MAINS SUPPLY  
Your Caspian Integrated Amplifier is set to operate from a fixed supply voltage which is marked on a label next to  
the mains input plug. Before connecting the mains lead please check that your mains supply corresponds to this  
label as below:  
230V Products ………………………………….Voltage Range: 220V – 240V  
115V Products ………………………………….Voltage Range: 100V – 120V  
100V Products ………………………………….Voltage Range: 90V – 110V  
The mains lead supplied with this product has an IEC mains socket which plugs into the IEC connector on the  
unit’s rear panel. The other end is normally attached to the appropriate mains plug for your country. In the UK  
this is the standard UK13A plug.  
This plug should ordinarily not be removed from the lead. If you do remove it, please dispose of it safely so that it  
cannot be plugged into a mains socket whilst in a potentially dangerous condition. We suggest that you obtain  
from your dealer a complete replacement lead.  
Should you move to another area where either the mains voltage or the mains plugs are different from those as  
supplied with your Integrated Amplifier, please contact the appointed ROKSAN distributor for assistance.  
Please observe correct mains polarity at all times.  
The Integrated Amplifier mains fuses are located on the rear panel next to the IEC mains connector. These must  
only be replaced by the fuse type and rating as described on the fuse rating label on the rear panel of the unit.  
If the equipment is likely to be unused for some time, unplug it from the mains supply.  
GENERAL CAUTIONS  
FCC WARNING  
This equipment may generate or use Radio Frequency energy. The user may lose the right to operate this  
equipment if unauthorised modifications are made.  
INTERFERENCE  
Properly installed, this unit should not cause harmful interference to radio communications, There is, however, no  
guarantee that such interference will not occur in a specific installation. If interference arises (which you can  
determine by switching the unit off and on) you could try to remedy this problem by the following:  
Re-orient or re-locate the receiving antenna  
Increase the distance between the Integrated Amplifier and receiver  
Connect the unit to a different mains circuit from that of the receiver  
Consult your ROKSAN appointed dealer or an experienced Radio/TV technician for help and advice  
LOCATION  
Your Caspian Integrated Amplifier should be located in a well ventilated area and kept away from sources of  
heat, dust, humidity and direct sunlight.  
The Integrated Amplifier may be positioned either as a free standing unit or alongside another audio/video  
product. Never place the Integrated Amplifier on carpet or any surface likely to hinder normal ventilation.  
Never allow liquids or other objects to fall into the unit.  
This unit contains no user serviceable parts. Do Not remove any panels or attempt to service it yourself.  
Unauthorised servicing will void the warranty.  
Roksan Audio ltd  
Caspian Integrated Amplifier User Manual  
CLASSIFICATION: General Use  
Version 3.07  
All specifications are liable to change without notice. E&OE  
Page 3  
ENGLISH  
 
INSTALLATION  
C a s p i a n Integrated Amplifier  
ROKSAN Caspian Integrated Amplifier- Front Panel View  
1
2
3
4
5
6
7
8
9
10  
11  
MODE  
CD  
TUNER  
VIDEO  
LINE 1  
LINE 2  
TAPE  
MODE  
TAPE  
R O K S A N  
INPUT  
VOLUME  
C a s p i a n  
Integrated Amplifier  
Mseries-1  
1.  
2.  
3.  
Input Selector  
Mode Button  
Mode Indicator  
4.  
CD Input Indicator  
5.  
6.  
7.  
8.  
9.  
10.  
11.  
Tuner Input Indicator  
Video Input Indicator  
Line 1 Input Indicator  
Line 2 Input Indicator  
Tape Monitor Indicator  
Tape Monitor Button  
Volume Control  
ROKSAN Caspian Integrated Amplifier - Rear Panel View  
1
3
5
7
9
2
4
6
8
10  
THIS  
PRODUCT  
MUST BE  
EARTHED  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
CD Input  
Tuner Input  
Video Input  
Line 1 Input  
Line 2 Input  
Tape Input (Playback)  
Tape Output (Record)  
15  
16  
11  
12  
13 14  
Roksan Audio ltd  
Caspian Integrated Amplifier User Manual  
CLASSIFICATION: General Use  
Version 3.07  
All specifications are liable to change without notice. E&OE  
Page 4  
ENGLISH  
 
8.  
9.  
Preamp Output 2 (Bi-Amping)  
Preamp Output 1 (Tri-Amping, Internally linked to Power Amp Section Input)  
Power Amp Input (Requires internal work for activation)  
Right Speaker Output  
Left Speaker Output  
AC Mains Input, filtered  
Voltage & Fuse Label  
AC Mains Fuseholder  
AC Mains Power Switch  
10.  
11.  
12.  
13.  
14.  
15.  
16.  
SETUP  
C a s p i a n Integrated Amplifier  
CONNECTING MAINS POWER  
Please refer to rear panel view on Page 4. The moulded IEC connector of the supplied mains lead should be  
plugged into the socket (13) on the rear of the unit first and then plugged into the mains supply. The Mains power  
switch (16) is on the rear panel of the Integrated Amplifier. This switch is normally left on. If the unit is likely to be  
unattended for a long period, switch it off and unplug the mains lead from the wall.  
SIGNAL CONNECTIONS  
Signal Input connections:  
There are five Inputs (1 – 5) on your Caspian Integrated Amplifier in addition to the  
Tape Input (6). All these inputs are line level inputs and will accept virtually all currently available source  
components.  
All the inputs use RCA Phono Connectors and should be connected according to the standard convention –  
Right Channel – Red; Left Channel – Black or White.  
Also in accordance with standard practice, the Upper row of Phono Sockets carries the Left Channel and the  
Lower carries the Right Channel.  
The Input Sockets are labelled with their legends upside down as well as the normal way round to assist you  
should you be connecting an input from a position in front of and above the amplifier.  
Phono Input Connections:  
As your Caspian Integrated Amplifier is a line level unit you cannot connect a phono  
cartridge directly to it but will need a dedicated phono preamplifier. The ROKSAN range of Caspian Phono  
Amplifiers accept conventional moving coil and moving magnet cartridges and have custom equalisation for the  
outstanding ROKSAN Shiraz cartridge. For a demonstration of ROKSAN state of the art turntable reproduction  
contact your authorised retailer.  
IMPORTANT NOTE: For optimum performance it is recommended to use high quality inter-connect cables such  
as ROKSAN HDC-02A high definition analogue Cable.  
LOUDSPEAKER CONNECTIONS  
The right and left loudspeakers are connected to the amplifier via the rear panel binding posts (11) and (12)  
respectively. There are two basic types of cable –  
Figure 8 cable has two insulated conductors which lie parallel, either side by side, or spaced by insulation.  
Overall sheathed cable has both conductors insulated and enclosed in an overall plastic sheath.  
Carefully remove any overal sheath or split the figure 8 cable to a depth of about 75mm (3”).  
Roksan Audio ltd  
Caspian Integrated Amplifier User Manual  
CLASSIFICATION: General Use  
Version 3.07  
All specifications are liable to change without notice. E&OE  
Page 5  
ENGLISH  
 
Carefully strip the insulation on each wire to a depth of about 12mm (1/2”) exposing the  
bare core. If the conductor is stranded, twist the strands together on each conductor.  
Unscrew the binding post. There is a cross-hole about 5mm from the panel end of the  
binding post. Insert the bared conductor through the hole and tighten the binding post  
securely making sure that there are no loose strands or bare ends protruding through  
the post.  
Carefully observe polarity ensuring that the RED (+) speaker terminal is connected to  
the RED (+) amplifier terminal and the BLACK (-) speaker terminal to the BLACK (-)  
amplifier terminal.  
When both left and right channels are connected to their respective speakers the  
amplifier is ready for use.  
IMPORTANT NOTE: For optimum performance it is recommended to use high quality cables such as ROKSAN  
HDC-02S high definition Loudspeaker Cable. Many speaker cables such as the ROKSAN HDC-02S are  
directional. Please observe this directionality. DO NOT use speaker cable with conductor size less than 16 AWG  
(1.6mm Diameter). The Binding posts accept conductor sizes up to 12 AWG.  
MULTI-WIRING AND MULTII-AMPING  
Multi-Amping The Loudspeakers  
If the Loudspeakers utilise more than one drive unit with individual input terminals, for example a Tweeter and a  
Woofer, then the loudspeaker performance will benefit from Bi-Amping. Dedicating one amplifier to the Tweeter  
and another to the Woofer isolates them from each other reducing distortion and increasing reserved power.  
Speakers work far better with most amplifiers when Multi-Amped than using one yet more powerful amplifier.  
Note: Bi-Wiring reduces the impedance seen by the Woofer and the Tweeter and is a first step towards Bi-  
Amping.  
LF  
LF  
MF  
HF  
HF  
Roksan Audio ltd  
Caspian Integrated Amplifier User Manual  
CLASSIFICATION: General Use  
Version 3.07  
All specifications are liable to change without notice. E&OE  
Page 6  
ENGLISH  
 
OPERATION  
C a s p i a n Integrated Amplifier  
Please refer to the front and rear panel views on page 4.  
SWITCHING ON  
The Mains power switch (16) is located on the rear panel of the amplifier. This switch should be left ON for  
normal operation. If unattended for a long period, the Mains power should be switched OFF and the lead  
disconnected from the power supply.  
When switched ON from the rear panel your Caspian Integrated Amplifier runs a self-test and the indicator lights  
on the front panel pulse twice. The amplifier then reverts to STANDBY and the MODE indicator light (3) will glow  
GREEN. The amplifier is now ready for use.  
You can activate your Caspian Integrated Amplifier in two ways:  
1
2
Press the MODE button (2) once.  
Rotate the INPUT selector (1) in either direction by one step.  
NOTE: The remote handset will activate the amplifier in the same manner.  
The Caspian will ‘wake up’ and the MODE indicator light (3) will glow RED. The amplifier will automatically select  
the CD input and the CD input indicator light (4) will glow.  
USING THE CONTROLS  
MODE CONTROL  
The MODE button has the following functions:  
It activates the amplifier from Standby.  
Pressing the MODE button once with the amplifier activated will mute the volume level by 20dB. The  
MODE indicator light will glow ORANGE. The amplifier remains fully functional in this mode. Another  
single press unmutes the amplifier and the MODE indicator light will revert to RED.  
With the amplifier activated, a sustained press on the MODE button reverts the amplifier to Standby, all  
the input indicator lights will be extinguished and the MODE indicator light will glow GREEN.  
NOTE: When you bring the Caspian out of STANDBY having switched it ON at the Mains, the input selector will  
default to CD (as described previously).  
When, however, the Caspian has been put into Standby from the MODE button, bringing it out of  
Standby will restore previously selected input, tape and mute values. Bringing the Caspian out of  
Standby by moving the INPUT Selector one step in either direction also leaves these amplifier settings  
unaffected.  
INPUT SELECTOR SWITCH  
The INPUT Selector is an endless rotary switch that moves round one click at a time. It connects each signal  
source to the amplifier by rotating through the Inputs with the exception of TAPE. Rotating the Selector  
continuously clockwise will select inputs in this sequence:  
CD – TUNER – VIDEO – LINE1 – LINE2 – CD - …  
Rotating the Selector anti-clockwise reverses the sequence.  
Whenever an input is selected the appropriate indicator light will glow.  
VOLUME CONTROL  
The VOLUME Control is a precision device. It follows a logarithmic law so that its response approximates that of  
the human ear. There is an illuminated indicator on the volume control to clearly show the appropriate volume  
setting.  
TAPE MONITOR  
When you select an input source, the INPUT Selector connects the selected source to the amplifier and connects  
this source to the Tape Output Sockets of the Caspian thus enabling you to record.  
The Tape Monitor is an override. Pressing the TAPE Button (10) connects the output of your tape deck to the  
Caspian, overriding the selected input. However, the selected input is left connected to the recording input of  
your tape deck. If you have a suitable tape deck, this facility enables you to record a programme whilst  
monitoring its playback.  
Roksan Audio ltd  
Caspian Integrated Amplifier User Manual  
CLASSIFICATION: General Use  
Version 3.07  
All specifications are liable to change without notice. E&OE  
Page 7  
ENGLISH  
 
When the TAPE Button is depressed, the TAPE Indicator light glows and the selected source Indicator remains  
illuminated.  
The input selector remains functional when the Tape Monitor is ON, allowing a range of sources to be recorded.  
Pressing the TAPE Button, toggles between Tape Monitor ON and OFF.  
REMOTE HANDSET  
The Caspian System Remote Handset uses two AAA size 1.5V batteries. These are housed in the battery  
compartment on the underside of the handset.  
Carefully remove the battery compartment cover and insert the supplied batteries in place observing polarity.  
Replace the cover. The handset is now ready for use.  
The front panel controls of the Caspian Integrated Amplifier are replicated on the remote handset.  
1
2
3
5
6
5
4
3
6
5
1 MODE  
2 TAPE  
3 INPUT (BACK)  
4 INPUT (FORWARD)  
5 VOLUME (DOWN)  
6 VOLUME (UP)  
2
1
MODEL 3  
MODEL 2  
The MODE Button (1) puts the amplifier in and out of Standby and can also be used to mute the output level by  
20dB.  
The TAPE Button (2) connects the Tape Deck (In & Out).  
The INPUT Buttons (3 & 4) cycle through the input sources (Back & Forward).  
The VOLUME Buttons (5 & 6) adjust the output volume level (Down & Up).  
Roksan Audio ltd  
Caspian Integrated Amplifier User Manual  
CLASSIFICATION: General Use  
Version 3.07  
All specifications are liable to change without notice. E&OE  
Page 8  
ENGLISH  
 
KNOW YOUR CASPIAN  
When you first power up from the Mains Switch on the rear panel, the amplifier runs a self-test during  
which all the Indicators pulse twice. When the self-test is complete the amplifier goes into Standby and the  
MODE Indicator glows GREEN.  
During Standby, the power stage of the amplifier shuts down to reduce power consumption and heat.  
If the amplifier overheats through overload or lack of ventilation, the Caspian will revert to Standby until it  
has cooled down. If it subsequently overheats the amplifier will revert to Standby and stays in Standby.  
You will then have to wait until the amplifier cools down fully and will have to bring it out of Standby  
manually.  
In the unlikely event of an internal fault such as a power supply failure, the MODE Indicator light will flash  
GREEN and the amplifier will shut down. The amplifier will then run a self-test. If all is well, the amplifier will  
revert to Standby. If the fault persists, the Indicator light will continue to flash.  
TROUBLESHOOTING  
C a s p i a n Integrated Amplifier  
If you suspect that your ROKSAN Caspian Integrated Amplifier is not operating properly, you should check all the  
connections carefully. Pay particular attention to speaker phasing and channel connections. Phono plugs should  
be fully inserted- a frequent cause of problems is that Phono plug surrounds do not make proper contact. Below  
are some commonly encountered problems with suggestions for possible cure. The list is not exhaustive: If you  
have any unresolved problems, please consult your appointed ROKSAN dealer or distributor.  
SYMPTOM  
LIKELY CAUSE  
SUGGESTED REMEDY  
No power  
AC Mains lead not inserted properly  
Ensure AC Mains lead is fully inserted  
Unit not switched on at rear panel  
Switch unit on at rear panel  
No output on one or both  
channels  
Amplifier in stand-by mode (MODE light Press MODE button to set amplifier in  
GREEN)  
operational mode (MODE light RED)  
Missing or bad input signal connection  
Incorrect speaker connection  
Wrong input selected  
Check all input connections  
Check speaker output connections on  
rear panel  
Select correct input, ascertain source is  
working  
Tape Monitor selected  
Over heating  
Deselect Tape Monitor  
Allow amplifier to cool, increase  
ventillation or use at lower volume  
Deselect MUTE (check volume setting  
first)  
Very low sound output  
Amplifier set in MUTE position  
Poor speaker imaging, lack  
of Bass output  
Loudspeakers connected out of phase  
Check polarity of speaker connections  
(especially important if Multi-wiring,  
Multi-Amping)  
Hum from speakers  
Incorrect Grounding  
Check Mains polarity and grounding on  
all connected equipment  
Roksan Audio ltd  
Caspian Integrated Amplifier User Manual  
CLASSIFICATION: General Use  
Version 3.07  
All specifications are liable to change without notice. E&OE  
Page 9  
ENGLISH  
 
GUARANTEE  
C a s p i a n Integrated Amplifier  
There are no user-serviceable parts inside your Caspian Integrated Amplifier. If a fault should develop, refer any  
servicing to your appointed ROKSAN dealer, distributor or approved service agent.  
Your ROKSAN Caspian Integrated Amplifier is guaranteed against any defect in materials and workmanship for a  
period of two years from the date of purchase.  
This guarantee only becomes effective if the warranty card is validated by the ROKSAN retailer from whom the  
equipment was purchased and returned to ROKSAN within 28 days of purchase.  
This guarantee excludes:  
1. Damage caused due to accident, missuse, neglect and incorrect installation, adjustment or repair.  
2. Liability for damage or loss during transit from the retailer or purchaser to ROKSAN or its authorised  
distributor for the purposes of repair or inspection.  
Carriage costs to ROKSAN shall be borne by the consignor.  
All claims under this guarantee must be made through an authorised ROKSAN retailer.  
If equipment returned for repair to ROKSAN is found on inspection to comply with the product specification  
ROKSAN reserves the right to make a charge for examination and return carriage.  
Unauthorised servicing will void this guarantee.  
NOTES  
C a s p i a n Integrated Amplifier  
Caspian Integrated Amplifier M series-1  
Serial Number: …………………………  
Year .……… Month …….. Day ……..  
Purchase Date  
ROKSAN Retailer  
Name:  
…………………………………  
Location: ………………………………  
Please keep a record for future reference  
Roksan Audio ltd  
Caspian Integrated Amplifier User Manual  
CLASSIFICATION: General Use  
Version 3.07  
All specifications are liable to change without notice. E&OE  
Page 10  
ENGLISH  
 
SPECIFICATIONS  
C a s p i a n Integrated Amplifier  
Line Inputs  
5 plus Tape  
47 k  
Input Impedance  
Input Sensitivity (80W)  
Line Outputs  
Line 240mV  
Tape, Preamplifier (x2)  
Output Voltage  
240mV (Tape Out)  
700mV (Pre Out)  
Power Outputs  
Output Power  
Loudspeaker, L & R  
85 Watts continuous, into 8Ω  
both channels driven  
120 Watts continuous, into 4Ω  
both channels driven  
Power Supply  
350VA Ultra Low Noise Toroidal Transformer  
4 Regulated Supply Rails  
Current Output  
Damping Factor  
Frequency response  
Gain  
50 Amps Peak to Peak  
>140 (8)  
-3dB, 1Hz – >100kHz  
40dB Overall (Pre & Power)  
9.3dB Preamplifier  
30.7dB Power Amplifier  
Harmonic Distortion  
Signal to Noise Ratio  
Power Source  
<0.003% 1kHz - 8Ω  
<0.003% 1kHz - 4Ω  
Line 108dBa (ref 500mV)  
85dBa (ref 1W, 8)  
100V – 120V 50Hz / 60Hz  
220V – 240V 50Hz / 60Hz  
(via filtered mains inlet)  
Power Consumption  
< 230 W  
Dimension  
Weight  
432 x 330 x 70 (W x D x H) mm  
432 x 330 x 80 (including feet)  
13 Kg  
Roksan Audio ltd  
Caspian Integrated Amplifier User Manual  
CLASSIFICATION: General Use  
Version 3.07  
All specifications are liable to change without notice. E&OE  
Page 11  
ENGLISH  
 

RAD Data comm Modem HCD E1 User Guide
RCA Cordless Telephone 21028 User Guide
RIDGID Metal Detector Metal Detector User Guide
Rotel Stereo Amplifier RA 870 User Guide
Samsung Camcorder HDR HC9 User Guide
Samsung Printer ML 1200 Series User Guide
Sanyo Camcorder VPC CG10BK User Guide
Saturn Automobile 2005 Relay User Guide
SBC comm Modem PCNT02 User Guide
Schumacher Battery Charger SE 1252MA User Guide