SxS Refrigeration
Users Guide
& Installation & Service Instructions
U109200-03
Introduction
DO NOT damage the refrigerant circuit. If
it does become damaged, do not use the
appliance.
Thank you for buying this high quality appliance, we hope
that it provides you with a stylish, yet practical solution to
your cooling needs. We hope that this handbook supplies
you with all the information you require, but please contact
us if there is any thing you are unsure of using the Customer
Care Centre number on page 28 of this handbook.
WARNING: Do not use mechanical devices
(i.e. hair dryers) to defrost this appliance.
•
When replacing old appliances, make sure that
you have disabled any locking mechanisms before
disposal – It may even be best to remove the
appliance door completely, to prevent children from
becoming trapped inside the appliance.
Warning:This appliance must be earthed.
Always make sure a qualified person installs
this appliance.
The freezer compartment is rated at 3 stars.
•
•
The appliance must be connected to the power
supply safely. Loose connections, broken plugs and
bare wires are a safety hazard. Make sure that all
connections are sound.
Important
Please be aware that this appliance is for domestic use only.
Before undertaking any routine maintenance or minor
repairs, disconnect the appliance from the electrical
supply. This includes cleaning, defrosting and
changing light bulbs.
The right hand side of this appliance is a refrigerator, and
should be used for storing fresh foods.
The left hand side of this appliance is used for freezing fresh
foods and storing frozen foods (convenience meals etc.)
•
•
Do not touch cold surfaces of the appliance while
it is in use as this will cause hands to stick to them
leading to freezer burns.
These instructions are intended for the user. They describe
the appliance and how to use it safely and correctly.
When moving the appliance take care not to damage
the leads, pipes or condenser unit. Should these
parts become damaged, contact a qualified service
engineer.
Before you start
•
•
•
Before you plug the appliance into the mains, clean
the inside of the appliance using warm water and
bicarbonate of soda, then dry thoroughly.
•
Effervescent liquids (fizzy drinks) should never be
frozen. These liquids expand during freezing and
this may lead to the bottles/containers shattering or
exploding.
Please leave the appliance to stand for at least six
hours. This will allow the cooling system to settle
following transportation.
•
•
Foods that are intended to be defrosted or cooked
first e.g. breads, meats etc., must not be eaten in
their frozen state.
Check that no parts of the appliance are damaged,
especially parts of the cooling system, pipes or
leads. If damage has occurred, DO NOT install the
appliance, you should contact a qualified service
engineer or return the appliance to its place of
purchase.
If food looks or smells strange, do not attempt to
eat it. If in doubt throw it away. Spoiled food can be
harmful to your health.
•
•
Never use electrical devices, such as hair dryers, to
defrost this appliance.
•
If the accessories inside the appliance have
been disturbed during transit, reposition them in
accordance with the instructions.
Never use sharp, metal implements to scrap ice off
the surface of this appliance. Only use implements,
which are fit for this purpose (i.e. plastic scrapers)
and use carefully to avoid damaging the lining of the
appliance.
Make sure that the electrical supply to your plug socket is
correct for this appliance – The required information is on
the data badge of the appliance.
Once the appliance is installed, cleaned and dry, it is ready
to be plugged in and switched on.
•
•
The cooling system contains refrigerant and oils, all of
which are harmful to health if leaked. Should leakage
occur, disconnect the appliance and ventilate the
room it is installed in. Take care to ensure that you do
not get any coolant near to, or in, your eyes.
Safety
The data badge is located inside the
appliance (refrigeration compartment).
Contact a service engineer or arrange to have the
appliance removed. Do not use the appliance under
any circumstances.
WARNING: Use potable (drinking) water with
this appliance.
WARNING: Keep this appliance clear of any
obstruction
3
U109200-03
and this may damage foods. Please ensure that the ambient
temperature does not drop below that specified by the
climate class and that temperatures are maintained as
consistently as possible.
Positioning Your Appliance
Choosing the right location
This appliance should be installed in a room, which is dry
and well ventilated.
Connection to the electricity supply
In order to ensure adequate ventilation, the appliance should
be at least 1.5cm clear on all sides from kitchen cabinetry,
and any units placed above the appliance must be clear by
1.5cm – allowing adequate ventilation for the appliance. See
clearance diagram.
Connect the appliance to the electrical supply (220 – 240V ~
50Hz) with the plug and lead, which are fitted. Connections
to the mains supply should be in accordance with local
regulations.
15mm
590mm
This appliance will operate within a range
400mm
450mm
of 187-253V. Operation outside this range
may result in damage to the control
panel, thermostat or compressor, unless a
regulator with a capacity of 750W, or higher,
is installed.
The appliance must be plugged into an
earthed socket.
•
Always make sure that the plug is accessible after the
appliance has been positioned.
15mm
•
The refrigerator is supplied with a standard three-pin
plug, of which the one for grounding should never be
removed.
Care for the external cable
•
Hold the plug, not the electrical cable, when
unplugging the refrigerator.
•
Ensure that the refrigerator does not trap the electric
cable.
•
•
Do not step on the cable.
Avoid damage to the electric cable when moving the
refrigerator.
Damaged electrical cable
When the electrical cable is damaged or worn, turn off the
refrigerator and consult an authorized agent for replacement.
If inflammable gas leaks in the vicinity of the
refrigerator
If located close to a corner adequate spacing must be left for
door opening and removal of shelves. Refer to diagram.
•
Turn off any leaking valve
•
Open the doors and windows
This appliance should be 10cm at least from any electric or
gas cooker and 30cm from any coal or oil stove. If this is not
possible, ensure that appropriate insulation is used.
DO NOT under any circumstances unplug
electrical appliances in the vicinity of the
leak.
Avoid exposing the appliance to direct sunlight, and sources
of heat (radiators, heaters, cookers etc.).
Unplug the refrigerator when:
If this appliance is situated in a cold environment (shed, out
house, garage etc.) it will affect its performance. You may
find that the performance of the appliance is not consistent
•
Cleaning or maintenance
•
Replacement of the lamp.
U109200-03
4
Adjustable feet
Make sure that the appliance is on solid level flooring. If
the refrigerator is placed on a plinth, flat, strong and fire
resistant materials must be used.
This appliance has front adjustable feet, which can be used
to level the appliance, or adjust door alignment (see below).
Door adjustment
The doors may require some alignment adjustment before
you connect the appliance to the electricity supply. This can
be done by making minor adjustments to the feet:
If the freezer door height is lower than the refrigerator
door, use a screwdriver in the slots of the front left hand
adjustable foot, turning clockwise until the freezer door
height is raised in line with the fridge door. If the freezer
door is lower, adjust the RH foot using the same method.
5
U109200-03
About Your Appliance
Appliance Layout
Dairy Compartment
Ideal for storing foods such as eggs, cheeses, butter,
cartons of milk etc, separate from stronger smelling food.
Shelves
Number of shelves supplied; 4 in the fridge, 3 in the freezer.
Salad / vegetable drawer (Upper Crisper)
The upper drawer inside the refrigerator is used for storing
fresh fruit and vegetables that require careful cooling.
The shelves will not pull out accidentally when you remove
foodstuff from the appliance.
Foods that are likely to perish quickly should be placed
towards the rear of the appliance – where it is coolest.
Meat drawer (Lower Crisper)
The lowest drawer inside the refrigerator can be used
to store fresh meat in a way, which will avoid cross
contamination with other fresh foods.
Bottle holder
The bottle holder is intended for storing larger bottles (soft
drinks, water etc.) inside the fridge.
The lights
The interior lights come on when the door is opened.
The performance of the light is not affected by any of the
appliances other settings. Should the light fail to work, it is
most likely that the bulb needs replacing. (See Changing the
Light bulb).
Like the shelves, the bottle holder will not pull out
accidentally and can be removed by holding the front edge
of the holder and tapping the underside upwards, until the
holder disengages from the 2 locations.
Warning: Always make sure that large
bottles do not prevent the door from closing.
Freezer compartment
Refrigerator compartment
Fan
Ice Maker (inside ice bin)
Ice bin
Lamp
Lamp
Cantilever shelf
Cantilever shelf
Storage shelf
Storage shelf
Freezer draw
Crisper
U109200-03
6
Before Using Your Appliance
Environmental Notes
Using Your Appliance
Our products have been packaged using environmentally
friendly materials. All packaging can be recycled. Please
contact your local authority for details on recycling centres in
your area.
Warning: Do not damage the refrigerant
circuit when installing or cleaning.
Warning: Do not use any kind of mechanical
device in any compartments of this
appliance unless they are of the type
recommended by the manufacturer.
Warning: Do not use any electrical devices to
defrost this appliance unless they are a type
recommended by the manufacturer.
Once the appliance has been installed and is connected
to the power supply the appliance will begin to work
automatically. You can adjust the settings of the appliance to
suit your requirements.
All old electrical goods must be disposed of correctly. You
should never dispose of them with household waste. Local
councils / authorities can advise you as to what services
they provide for the disposal of old products – please be
sure that you contact them in order to dispose of all old
appliances.
Once the temperature required inside the appliance has
been reached, you should begin to load it with food. We
would recommend that you do this all in one go to prevent
repeated opening and closing of the door. See ‘Setting and
Adjusting the Temperature’ for more information.
Many of the components in this appliance can be recycled.
Note:The time required to reach the desired
temperature will vary, depending on the setting
chosen, the amount of food and the ambient
temperature.
Energy Saving Tips
Energy saving is especially important with cooling products.
•
•
•
Check regularly that your appliance is well ventilated.
Poor air circulation around the appliance can lead to
inefficient operation.
Temperature selection
Higher settings on the thermostat (towards 5) mean lower
(colder) temperatures within the appliance (See guide
below).
Whenever possible adjust the thermostat to reflect
seasonal changes, and changes in the quantity of
food stored inside.
Under certain conditions (Highest setting and low ambient
temperature), the temperature inside the refrigerator can
Freshly cooked foods, which are to be frozen, should
be cooled to at least room temperature before
freezing.
drop below 0 C.
It is recommended that when the ambient temperature is
normal you set the thermostat to a medium setting.
Use the highest setting only when required or
recommended.
Note:Temperatures within the appliance can be
affected by frequent opening of the door. Always
try to keep the length of time the door is open to a
minimum.
•
•
•
Layers of ice and frost increase energy consumption
– make sure that your appliance is free of heavy frost
and ice.
Temperature Guide
Compartment DISPLAY
1
2
3
4
5
FREEZER
FRIDGE
Level
Level
Should the door seal become dirty or damaged,
please clean or replace it. A poorly working door seal
is detrimental to the performance of the appliance.
-15°C -17°C -18°C 20°C -22°C
1
2
3
4
5
7°C
6°C
5°C
4°C
3°C
The vents at the rear of the appliance should always
be clear/cleaned of dust and obstruction. Regularly
checking, and cleaning if need be, should help to
keep the appliance running effectively.
Ensure that the appliance is installed in accordance with the
instructions given in this handbook – Failure to do so could
invalidate your warranty, resulting in service charges being
incurred, should you need an engineer.
7
U109200-03
The Control Panel
E F G H I J
5
•
3
•
1
A
B
C
D
E
Quick Freeze
F
G
H
I
Freezer temperature indicator
Refrigerator temperature indicator
Crushed ice selected
Freezer temperature
Refrigerator temperature
Ice/Water
Water selected
Freezer indicator
J
Cubed ice selected
Setting and Adjusting the Temperature
‘Quick Freeze’
F
G
E
5
5
•
3
•
•
3
•
1
1
To use the ‘Quick Freeze’ function, press button A. Indicator
E will illuminate to show you that the function is operational.
To switch ‘Super Freeze’ off, press button A again
– indicator E will go out.
To adjust the refrigerator temperature, press button C. The
indicator (G) will illuminate. Each subsequent press of button
C will adjust the temperature scale by one. To clear the
setting, simply keep pressing button C until indicator (G) is
back to level 1.
Note:The quick freeze function will operate until
the selected temperature level (1 to 5) has been
established.
To adjust the freezer temperature, press button B. The
indicator (F) will illuminate. Each subsequent press of button
B will adjust the temperature scale by one. To clear the
setting, simply keep pressing button B until indicator (F) is
back to level 1.
Open Door Warning
Should the door be left open for an extended period, an
alarm will sound to remind you to close the door.
Control Function Display
30 minutes after the final press of any button, the display
will go blank. The display will illuminate when the door is
opened, or if you press any button.
U109200-03
8
Beverages with high alcohol content should be stored
vertically in tightly sealed bottles.
Switching the refrigerator On/Off
Foods should not touch the rear wall of the appliance.
G
Delicate foods should be stored in the coolest part of the
appliance.
Try not to open the door too often.
5
Set the thermostat to make sure that foods remain suitably
cold, try to avoid freezing within the fridge. Using a
thermometer will help you to judge how cool the appliance
is. Place it into a glass of water and leave it inside the
appliance for several hours to get a reliable reading.
•
3
•
1
Some foods contain natural oils and acids (e.g. citric acid)
which can damage plastics if spilled – make sure these
foods are suitably contained.
Unpleasant odours inside the fridge are a sign that
something has spilled and cleaning is required. Using warm
water with bicarbonate of soda will clean the interior of the
appliance and remove most spillages. (See cleaning your
appliance).
To switch off the refrigerator, press and hold button C for a
few seconds. The icon (G) will disappear.
To switch the refrigerator on again, press and hold button C.
Icon (G) will reappear and the appliance will begin to run as
usual.
Always remember to remove perishable foods from this
appliance before taking prolonged trips of holidays.
Try not to open the door too often.
Storing fresh foods
Freezing fresh foods
Packaging fresh foods properly, using the correct
temperature and taking into account food hygiene will
enhance the quality of fresh foods stored within this
appliance.
As with storing fresh foods, suitable packaging, correct
temperature and food hygiene will enhance the quality of
the food you are freezing.
Make sure that all foods for freezing are of a high quality,
and suitable for freezing.
Use plastic bags, aluminium foil or other food wraps to cover
fresh foods not in packaging to prevent flavour transfer and
prevent contamination.
Make sure that foods, which have been cooked and require
chilling, are at room temperature before placing them into
the appliance. Make sure that these foods are stored in
suitable containers.
Before storing items in multi packs (i.e. yoghurt) remove any
excess packaging.
Make sure that foodstuffs are stored systematically (raw
meats with raw meats, dairy with dairy) to avoid flavour
transfer and cross contamination. Raw meats should be
stored towards the bottom of the appliance to prevent the
possibility of it dripping onto uncooked food. Other foods
should be stored above raw meat.
Use suitable packaging (plastic bags etc.) to store food in,
and make sure that it is air tight or well sealed. Leaking
packaging will dehydrate the products and lead to loss of
beneficial vitamins.
Mark packages with the kind of food contained and the date
of storage.
Food needs to be frozen quickly, so it is best to freeze small
portions whenever possible and ensure that they are as cold
as possible before storage. The recommended maximum
weight for each portion is 2.5kg.
Keep food which is fresh away from food which is already
frozen, if you need to freeze fresh food every day, make
sure that it is in small portions to prevent this.
Never store anything, which is flammable,
Do not exceed the maximum load for freezing – which is
given as 10kg / 24H - see data badge for details.
volatile or explosive inside the appliance.
9
U109200-03
Freezing procedure
This appliance is fitted with a ‘Quick Freeze’ function. This
function is ideal if you are freezing large quantities of foods
as it freezes quickly helping to preserve freshness and
maintain the level of nutrients in foods which can be lost
through freezing.
5
•
3
•
1
To prevent undue temperature rises; you should wrap the
foods in layers of insulating material, such as newspaper,
to help to maintain their temperature. It is also important
that any food affected by this situation should be either
consumed or cooked and re-frozen (where suitable) soon
afterwards in order to prevent health risks.
It is also advisable to use this function before you clean
the appliance interior to ensure that foods are as frozen as
possible.
Layers of newspaper can also be used to help keep foods
cold while you are defrosting the freezer (see cleaning your
appliance).
Storing frozen foods
Storage areas
When storing commercially frozen foods, please follow
these guidelines.
About your Freezer Compartment
As with the refrigerator, certain areas of the freezer are
better for storage of certain foods.
Always follow manufacturers’ guidelines for
the length of time you should store food for.
Do not exceed these guidelines!
Ice creams and water ices are best stored towards the rear
of the appliance where it is coldest.
•
•
•
Try to keep the length of time between purchase and
storage as short as possible to preserve food quality.
Large / heavier portions of food, such as meats joints for
roasting are best stored in the drawers at the bottom of the
appliance, while less weighty items should be stored on the
shelves – this is to prevent damage to the appliance.
Buy frozen foods, which have been stored at a
temperature of –18°C or below.
Avoid buying food which has ice or frost on the
packaging – This indicates that the products might
have been partially defrosted and re-frozen at some
point – Temperature rises affect the quality of food.
You should always make sure that food stored is suitable
for freezing, and that you have stored it securely inside the
appliance.
•
•
When consuming ice cream or water ices allow them
to warm a little first to prevent freezer burns on hands
or tongue.
Should there be a power cut, or the freezer /
refrigeration appliance fail for any length of time you
may need to remove food from the freezer and store
in a cold, hygienic place (i.e. garage or out house
area) until the power is restored, or the appliance is
repaired.
U109200-03
10
the drawer first. Lift the food shelf in an upward direction at
the rear (1) and pull it towards you (2). Then turn the shelf
into position (3). You must have the appliance door open by
90°.
Defrosting food for cooking
Should food become partially thawed, or defrosted it should
be consumed as soon as possible as the quality will be
affected by defrosting.
Always make sure that food is thoroughly
defrosted before cooking and no ice crystals
remain.This is especially important for
poultry, as this can be extremely harmful to
health.
1
Always follow the defrosting instructions
on packaging when defrosting ready meals
– manufacturers’ guidelines are always best, as
some frozen foods should be cooked from frozen.
4
2
About your Refrigeration Compartment
Temperature differences exist inside the refrigerator so it
is sensible to store different foods in different areas of the
appliance.
4
1. Eggs, butter and cheeses. (Dairy compartment with
cover)
4
2. Smaller bottles, cans, jars, packages.
3
3. Large bottles, soft drinks, water, wine etc.
4. Any fresh produce – store carefully to avoid cross
contamination.
4
5. Salad / vegetable drawer
6. Fresh, uncooked meats – store carefully to avoid cross
contamination and spillages.
5
3
Crisper compartment
To keep fruit and vegetables crisp and fresh, this appliance
has a crisper compartment with adjustable humidity.
6
High humidity will keep foods such as grapes, cucumbers,
kiwi etc. fresh and crisp - this is achieved by opening fewer
holes in the moisture control.
3
Lower humidity is ideal for storing foods such as
strawberries, melons, tomatoes and beans. Opening
more holes in the moisture control will lower the humidity
accordingly.
Always make sure that the front edge of the crisper
compartment is underneath the crisper cover. When
removing the crisper, remove the compartment first before
the cover.
To remove the cover of the crisper (for cleaning etc.) remove
11
U109200-03
Using the Icemaker & Water Dispenser
Before using the Icemaker/Water
Dispenser
How the icemaker works
In every cycle 8 ice cubes are produced.
Capacity of the icemaker depends on the freezer
temperature, the ambient temperature of the environment
around the appliance and how often the freezer door is
opened.
Water supply installation
Pressure of the cold water supplied to the automatic
icemaker is between 1.5 - 8.5Bar.
Installation instructions for the connection kit (to
a potable/drinking water supply) are found inside
the fridge.
Do not store ice cubes, which are produced during the
first batch of cubes following appliance start up, or after a
prolonged break. Discard these cubes.
Caution: Only an authorised person should
To ensure that the ice cube tray is filled to maximum
capacity, you will need to manually arrange the ice cubes
periodically.
install the water pipes and filter.
•
The water tube should be of an appropriate length
- usually 12 metres - and should be free of bends
after being inserted into place. If the tube is too long
then pressure will be reduced, therefore reducing the
capacity of ice making.
Some ice cubes may stick together when dropped into the
storage box – you will need to separate these to ensure
maximum use of the icebox.
First use of the icemaker / water dispenser
•
•
•
Always use potable / drinking water.
Do not consume the first seven (approx)
glasses of water, as there may be dust and /
Keep the water tube clear of heat sources.
or impurities within the water pipes.
The water tube should be installed and tested by
authorised personnel.
This will ensure that the pipes are cleared.
If in doubt, keep re-using the dispenser until the water runs
clear.
•
When used for the first time, press and hold the
cold-water button for one minute to prime the water
supply. Do not press the cold-water button for any
longer as this may cause the valve to heat up.
Noises during ice making
The ice making process can be noisy. You may hear ice
being dropped into the storage compartment. This is
perfectly normal.
Precautions
•
•
•
Never expose the water pipe to temperatures below
0°C to avoid freezing.
Storing ice for extended periods
Test the tubing for leaks by flushing the tube through
with water, until the water runs clear.
Ice, which is stored for a long period of time, may go an
opaque colour and have a strange odour. We recommend
that you dispose of this ice, remove and clean the icebox.
Allow the tray to dry thoroughly and cool down before
replacing into the appliance to prevent ice from sticking.
After the appliance has been sited into the location
of your choice, make sure that the water tube is
arranged so it does not incur damage through bends
and kinks and is clear of any heat sources.
Preventing ice from being made
•
•
•
A qualified appliance installer must install this
appliance.
If you do not require any ice over a prolonged period of time
(i.e. during winter) you can switch off the valve between the
water supply and the appliance. It is recommended that you
clean the icebox, dry it carefully and replace it back into the
appliance – this will prevent any odours being produced.
Once the temperature inside the freezer is at -15°C
ice production will begin.
Do not over use the icemaker. If you attempt to use
the ice cube button too often it will go into a shut
down mode. This is perfectly normal and requires you
to wait for one hour before attempting to re-use it.
•
•
Do not use delicate or fragile glassware.
Do not touch the ice cube outlet with your hands, or
any implements to avoid injury or damage.
U109200-03
12
Installation/Removal of the ice cube storage
tray
To remove the icebox, press the top of the drawer and
simultaneously pull the bottom, releasing the unit.
Using the Icemaker & water dispenser
There are three options available with this accessory –
crushed ice, cool water or ice cubes. Always make sure that
you hold your glass up to the dispenser before making your
selection to avoid spillages.
Crushed ice supply
1. Hold the glass to the dispenser.
5
•
3
•
1
2. Press the button for crushed ice.
3. Slightly push the glass onto the lever switch and the
crushed ice will be dispensed into the glass.
If the icebox cannot be easily fitted, remove it and turn
the corkscrew mechanism 90°. Then reinstall the icebox,
ensuring that the catch pin on the tray fits into the slot on
the shelf.
Ice cubes
1. Hold the glass to the dispenser.
5
•
3
•
1
If the ice maker does not work properly
The volume of the icebox equals the quantity of ice cubes,
which the appliance can make in one day. Occasionally
small number of ice cubes may remain inside the box. If the
ice gets stuck, this will result in abnormal operation of the
ice cube maker. To avoid this problem, remove the icebox
and rearrange the ice cubes, and remove ice cubes, which
cannot be separated.
2. Press the button for ice cubes.
3. Slightly push the glass onto the lever switch and the ice
cubes will be dispensed into the glass.
Always keep the ice cube outlet clean and
clear of obstructions.
13
U109200-03
•
•
Regularly clean the dispenser.
Cool water supply
1. Hold the glass to the dispenser.
Crushed ice may be dispensed instead of cubed ice if
crushed ice was the last option selected.
Never place canned drinks or foods inside
the dispenser, as this will damage the
crushing mechanism.
5
•
3
•
1
Do not touch the dispenser, or remove the
icemaker cover to prevent accidental injury
or damage to the appliance.
•
First supply of water (seven glass approx) and ice
cubes (20 pieces approx) should not be consumed
after initial start up or following a lengthy break in
use. Dispose of these accordingly.
•
•
Do not place ice cubes, which have not been
produced by the icemaker into the storage drawer to
prevent damage to the mechanism.
Insufficient water supply may lead to small ice cubes.
Excessive water supply may lead to larger cubes,
which may stick together, cause leaks and block the
dispenser. You should adjust the faucet or contact a
service engineer.
2. Press the button for cool water.
3. Slightly push the glass onto the lever switch and the
cool water will be supplied.
Notes:
When crushed ice is supplied;
Automatic defrosting
Some times you may receive crushed ice when you
have selected ice cubes as there may be crushed ice
remaining in the crushing mechanism. This is normal.
Try again until you receive ice cubes.
There is no need to defrost the refrigerator as this appliance
has automatic defrost.
Do not use mechanical devices to accelerate
the defrosting process – unless they are of a
If crushed ice is supplied frequently, you may notice a
build up of ice around the front of the icebox. This will
defrost automatically and is not a problem.
type recommended by the manufacturer.
In the event of a power cut
When cool water is supplied;
Should there be a prolonged power cut you may need to
remove food from the freezer compartment and store it in
a cold place, wrapped in layers of newspaper to preserve
suitable temperatures.
Following installation, cool water may not be available
immediately. This is due to air in the pipes. Press the
cool water supply button until water is dispensed to
clear the air. This can take up to two minutes.
In the event of a power cut, food should
remain safely cold for 3 hours approx.
The water supply will become cooler and cooler
gradually.
Once power is restored – replace the food back into the
freezer compartment.
Cool water does not contain ice – this should be added
before the water.
Should food begin to defrost, or the power cut last longer
than expected, it is advised that you consume any food
removed from the freezer.
Safety
Do not use excessively deep, narrow, fragile
If the power outage is short term, most foods can be left
inside the freezer compartment – this is the best way of
preserving temperature – and surrounded by ice cubes from
the icebox. This is also an ideal solution for power outages
you may have been pre warned about.
or delicate glasses.
•
•
Hold the glass as close as possible to dispenser to
avoid spilling water, dropping ice or blockages in the
ice cube dispenser.
When experiencing a power cut of any kind, do not add any
extra foods to the freezer.
Five seconds after the final delivery of ice or water,
the dispenser flap will close with a ‘phutt’ sound.
Hold the glass still for a further 2 – 3 seconds (for
ice), 1 - 2 seconds (for water) after you have filled
your glass and released the lever switch as additional
water or ice may be produced.
U109200-03
14
When not in use
Maintenance and Cleaning
If you are not using the appliance for an extended length of
time, it is recommended that you switch of the electrical
supply, empty any food out, clean the inside of the appliance
and leave the door ajar. This will save energy, and also
prevent a build up of stale odours inside.
Cleaning the inside of your appliance
•
Always disconnect the electricity supply before you
start cleaning.
•
•
Empty the appliance of food and remove the shelves.
The interior can be cleaned using warm water and
bicarbonate of soda, with a soft cloth. Make sure
that the interior is then dried carefully with a suitable
cloth.
Do not use harsh abrasives, or aggressive
cleaners as these can damage the interior of
the appliance.
•
Shelves and other accessories (plastic and glass
parts) can be cleaned in the sink using liquid dish
washing liquid and warm water. Make sure all soap is
rinsed off and all parts are dry before replacing them
inside the appliance.
•
Always keep the door seals clean.
Changing the plug (UK)
This appliance comes fitted with a 13amp plug fitted. Should
you need to replace the fuse, a 13amp ASTA approved
(BS 1362) must be used. Should the plug itself need to
be replaced, the wires in the mains lead are coloured in
accordance with the following code:
Removing the shelves/Salad/vegetable
crisper cover
•
Lift the food shelf in an upward direction at the rear
(1) and pull it towards you (2). Then turn the shelf into
position (3). You must have the appliance door open
by at least 90°.
Green and yellow = Earth
Blue = Neutral
Brown = Live
Earth - Yellow/Green
Live - Brown
Neutral - Blue
•
To remove the crisper cover, remove the crisper
drawer first and then follow the above directions.
Do not wash plastic parts in a dishwasher.
Clean the exterior of the appliance with a soft cloth and an
alcohol based cleaner. Do not use abrasive cleaners on the
exterior of the appliance.
Wiring of a standard 13 amp British three- pin plug
The wire coloured green and yellow must be connected to
terminal marked with the letter E, coloured green and yellow
or marked with the earth symbol:
The vents at the rear of the appliance should be cleaned
periodically using a soft bristled brush or the brush
attachment of a vacuum cleaner.
The wire coloured blue must be connected to the terminal
marked with the letter N, or coloured blue.
Once cleaning is completed, reconnect the electricity supply
and replace the food.
The wire coloured brown must be connected to the terminal
marked with the letter L or coloured brown.
Upon completion, there must be no cut or stray wire present
and the cord clamp must be secure over the outer sheath.
15
U109200-03
The appliance has recently been filled with more food
than usual.
Changing the light bulb
Before replacing the light bulb, switch off the electricity
supply to the appliance and unplug the appliance.
Ventilation is compromised – the vent requires cleaning
or clearing from obstruction.
Lamp required: 220 – 240V~25W (fridge only)
Lamp required: 220 – 240V~40W (freezer only)
There is inadequate ventilation around the appliance
– other appliances or units are too close. The appliance
has been overloaded with food for chilling or freezing.
Lamp holder: E27 (Do not exceed the
wattage given for lamps)
The ‘Quick Freeze’ function has been switched on.
To replace the lamp;
The outer casing of the appliance is warm
1. Pull the lampshade towards you.
2. Hold up (1) and pull out (2) the lampshade.
The appliance may become warm on the outside when
first switched on to prevent condensation forming.
The lamp does not work
3. Rotate the lamp anticlockwise until the lamp is
released.
The appliance is not plugged into the wall socket / a
fuse has blown.
4. Always replace the bulb with one that is identical.
Bulbs are not covered by any warranty, but can be
purchased at your local hardware store. Remember to take
the old bulb with you if you are unsure of what kind of bulb
to buy.
The bulb requires replacing.
The temperature inside the appliance is not right
The door has not been closed properly.
The appliance is too close to a heat source, or in direct
sunlight.
The vents at the rear are blocked / obstructed.
The appliance is making noises
MAX
25W
The appliance is cooled by the compressor, which will
make a certain amount of noise when the appliance is
switched on. The amount of noise depends on the age
of the appliance (older appliances may become noisier),
the positioning of the appliance (a levelled appliance is
less noisy) and how the appliance is used.
During use, you may hear the sound of the refrigerant
being circulated, and the sound of it flowing when
the compressor is off. The sound of the compressor
itself, which is a humming sound and a click when the
compressor switches off and on.
Troubleshooting
The appliance fails to work when first connected
to the electricity supply.
When you are starting the appliance for the first time,
or have had the appliance switched off for a prolonged
length of time, the sounds described above may be
louder.
Check there are no faults with the socket you are using
by plugging in an appliance you know to be working.
You may hear hissing or gurgling noises from the
appliance – these are due to the automatic defrosting
process.
Make sure that you have switched the appliance ‘on’.
The voltage may be incorrect.
Piping and the evaporator may also make noises should
the ambient temperature around the appliance change.
The appliance seems to be continually running.
If noises seem to be too loud, or a little unusual it
is more than likely because the appliance requires
levelling, or it is touching a unit.
The appliance will make a sound when first started; this
will gradually fade over a period of time.
The door has been opened frequently.
The door isn’t properly closed because the seals need
cleaning, or are damaged.
The door is damaged – leading to it dropping out of
correct alignment with the appliance.
U109200-03
16
Warranty/After Sales Service
If consultation or technical assistance is needed, please
provide the local authorised service agent with the purchase
invoice and the product code/serial number, which is located
inside the refrigerator – Top left hand side.
The 2 year free maintenance for the operation of the
appliance started from the date of purchase of this product.
Any cosmetic damage to the appliance must be reported
within 90 days of delivery.
For in-warranty service please call 0845 6035312.
For general enquiries please call 0870 7895107.
17
U109200-03
Consumer Products
|