Radio Shack Speaker PPHP1595 User Guide

PPHP1594 PPHP1595  
OWNER'S MANUAL  
www pyleaudio com  
 
PPHP1594 PPHP1595  
ABOUT THE PPHP1594 PPHP1595  
ABOUT THE PPHP1594 PPHP1595  
Applications  
Live sound reinforcement, speech and vocals, music playback in entertainment, A/V, and institutional venues -  
especially when ease of use and portability are important factors.  
Features  
15" low-frequency driver with dual neodymium magnet for low-distortion and light weight.  
Parallel Speakon connections allow daisychaining of a second speaker.  
Integral 35mm pole mount receptacle with securing thumb screw.  
Multi-angle enclosure for front of house or stage monitor application.  
Extended low-frequency performance. Delivers powerful bass down to 40Hz.  
Loudspeaker Placement and Mounting  
The following guidelines will help you achieve optimum sound wherever you use your PPHP1594 PPHP1595 loud-  
speakers:  
Raise the speakers as high as possible. For best results try to get the high frequency horn at least 2 to 4 feet above the  
heads of the audience. If the speakers are too low, the people in the back of the audience will not receive the best quality  
of sound.  
Place the speakers between the microphones and the audience. Feedback occurs when the microphones pick up sound  
from the speakers and "feed" the sound back through the sound system. If space is limited, point the speakers away  
from the microphones to reduce feedback.  
Locate the speakers away from turntables. Low-frequency feedback occurs when the output of the speaker is picked up  
by the tone arm of the turntable and is re-amplified. A heavy, solid turntable base and shock mounting can also reduce  
this type of feedback in DJ applications.  
Use more speakers in large or highly reverberant spaces. Spreading speakers throughout these spaces will produce  
much better sound than trying to compensate with loudness level or equalization. For very long distances, the use of  
another set of speakers on a delay is recommended.  
Stand speakers upright for PA-Tilt the speakers back for stage monitoring. Upright stance Provides even Coverage over  
a wide, PPHP1594 PPHP1595 speakers ane also designed with two slanted Positions for stage monitoring applications.  
2
 
PPHP1594 PPHP1595  
TROUBLESHOOTING  
TROUBLESHOOTING  
What to do  
Symptom  
Likely Cause  
Speaker not connected to  
amplifier  
Verify that speaker is connectedand that  
the amp is on  
No sound  
Re-seat the cable at both ends.  
Substitute a known-good cable  
Speaker cable is faulty or  
improperly connected.  
Check VU meters on the source mixer  
Verify that the tape or CD is playing.  
Use headphones to verify that the  
instrument is actually sending an  
audio signal  
Signal source(mixer, instrument,  
etc.) Is not sending a signal.  
NO sound. Speaker comes on.  
Disconnect and re-seat signal cables.  
Replace suspected cable with a  
known-good cable  
Faulty cables and connections  
Excessive input signal, trying to  
exceed the capabilities of the  
speakers  
Signal sounds distorted and very  
loud.  
Turn down the level controls on the  
amplifier.  
Use additional speakers.  
Review the Owner's Manual for your  
mixer and adjust controls as needed.  
Input sensitivity (gain)  
Signal sounds distorted even at  
moderate volumes.  
Mixer or other source is  
overdriven  
Channel faders  
Master faders  
Disconnect the devices that are connected  
to your speaker one at a time. If the noise  
goes away, the problem is with the source  
or the connecting cable.  
Noise or hiss heard at output  
Noisy source device  
Move the speakers so they do not point  
the microphone's pickup pattern.  
Microphones are pointed into the  
speakers  
Speakers feed back and howl when  
the microphone volume is turned up  
Locate the feedback frequency and reduce  
it using an equalizer.  
Equalizer settings art incorrect  
Excessive gain  
Reduce the gain at the mixer and move the  
microphone closer to the sound source.  
3
 
PPHP1594 PPHP1595  
SPECIFICATIONS  
Specifications  
Rugged, Light-Weight Co-Polymer Enclosure  
Multi-angle enclosure for Front of House or Stage MonitorApplication  
Power Rating: 375W RMS 900W Peak  
Integral Frame 15'' Woofer w/Dual Neodymium Magnets  
2'' Kapton VC  
1'' Titanium Compression Driver, Ferro-Fluid Cooled  
Frequency Response (±3dB): 35Hz-20kHz  
1W@1M SPL: 108dB  
Impedance: 8 Ohms  
Crossover Frequency: 2.8 KHz  
Inputs: Dual Speakon (Parallel)  
Integrated 35mm Speaker Mount  
Dimensions: 27.5''H x 17.5''W x 14.1''D  
Weight: 35.2 lbs.  
Frequency Response  
DBSPL  
/1.0W/m  
120  
110  
100  
90  
80  
70  
60  
30  
50  
100  
200 300  
500  
1K  
2K  
3K  
5K  
10K  
20KHz  
4
 
Place  
Stamp  
Here  
PYLE PRO Audio, Inc.  
1600 63rd Street  
Brooklyn, NY 11204  
 
Thank you for purchasing this PYLE  
product. To activate your  
warranty, please mail this card  
within 10 days.  
 

Radio Shack Car Satellite Radio System 10M User Guide
Radio Shack Cordless Telephone ET 1102 User Guide
Rancilio Coffeemaker Millennium User Guide
RCA Universal Remote RP5036 User Guide
Realistic Welding System PRO 2006 User Guide
Remington Power Tools Chainsaw 100089 06A User Guide
Ricoh All in One Printer MP5500 User Guide
Ricoh Digital Camera RDC 300Z series User Guide
Scientific Atlanta Network Card DPX2213 User Guide
Sears Blower 45 04071 User Guide