Radio Shack Radar Detector Cat No 22 1698 User Guide

Owner’s Manual

VG-2 Guard

X•K•Ka Superwide Radar/Laser Detector

w/Safety Light

Please read before using this equipment.

Cat. No. 22-1698

360× Detection — detects laser signals from both the front

and the rear of your vehicle.

City/Highway Modes — let you minimize alerts when you are

in areas that have false radar sources.

FAST (False Alert Suppression Technology) — helps pre-

vent false alarms caused by non-traffic radar sources.

Auto Quiet — lets you set the radar detector to give you a full-

volume alert for about 5 seconds, then reduce its alert to mini-

mum volume.

Your radar/laser detector includes the following items:

•

Coiled Power Cord

Windshield Bracket with Suction Cups

Hook and Loop Fastener

We recommend you record your detector’s serial number

here. The number is on the detector’s bottom panel.

Serial Number: _________________________________

Important: Some areas have laws regulating the use of radar

detectors. Check with your local law enforcement agency

about the laws in your area.

One or more of the following patents apply: 4,315,261;

5,146,227; 5,379,456. Other patents pending.

CONTENTS

A Quick Look . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Mounting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Hook-and-Loop Tape Mounting . . . . . . . . . . . . . . . . . . . 8

Windshield Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Detector Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Turning the Detector On and Off . . . . . . . . . . . . . . . . . 11

Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Demonstrating Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Muting Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Using Auto Quiet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Selecting the City and Highway Modes . . . . . . . . . . . . 13

Setting the VG-2 Option . . . . . . . . . . . . . . . . . . . . . . . . 14

Receiving and Identifying Alert Signals . . . . . . . . . . . . 15

Resetting the Detector . . . . . . . . . . . . . . . . . . . . . . . . . 16

Safety Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Using Vehicle Battery Power . . . . . . . . . . . . . . . . . . . . 18

Installing/Replacing Batteries . . . . . . . . . . . . . . . . . . . . 18

Charging Rechargeable Batteries . . . . . . . . . . . . . . . . 20

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Replacing the Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Replacing the Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

A QUICK LOOK

Rear Laser Detection Lens

signals from the rear.

— receives incoming laser

— turns the detector on

PWR (Power/Volume) Button

and off and lets you adjust the volume.

MUTE Button —

press before a radar/laser signal is

detected to reduce the level of audio alerts that sound

when there is a signal. Press after a signal is detected to

silence the alert, but still have visual alerts to keep you

informed.

CITY Button

— reduces false alerts typically encountered

MUTE

in urban driving areas. Also works with the

turn the VG-2 option on or off.

button to

5. Band Identifying LEDs — identify the type of radar

detected.

6. Digital Display ∇ προϖιδεσ διστινχτ ϖισυαλ χονφιρµα

τιον οφ σιγναλ στρενγτη ανδ ινδιχατεσ τηε σελεχτεδ

οπερατινγ µοδεσ.

7. Speaker — sounds distinct audio alerts.

8. Power Jack — the power cable plugs in here.

9. Bracket Release Button — lets you quickly remove the

detector’s bracket.

10. Front Laser Detection Lens — receives incoming laser

signals from the front.

11. Radar Detection Antenna — receives incoming radar

signals.

12. Mounting Bracket Slot — holds the windshield mounting

bracket.

INSTALLATION

MOUNTING GUIDELINES

Follow these guidelines when selecting a location.

•

Choose a location that does not block the driver’s view of

the road.

Mount the detector in a level position with a clear view to

both the front and rear.

The detector’s view of the road must not be blocked by any

metal object.

Some vehicles have InstaClear or ElectriClear defogging

windshields, which have metal coatings that block signals.

General Motor’s APV vans have a solar shield that keeps

the vehicle cooler during the summer, but also blocks sig-

nals. A detector installed in a vehicle with any of these fea-

tures will probably not detect a signal.

•

Since window tinting reduces the received strength of laser

signals, you should not mount the detector behind any

tinted glass.

Do not mount the detector where the driver or a passenger

might hit it in a sudden stop or accident.

Caution:

Whichever mounting method you choose, place the

detector out of view when you leave the vehicle. This keeps

the detector out of sight of thieves and prevents exposing it to

extremely high temperatures, which can temporarily impair

performance.

HOOK-AND-LOOP TAPE MOUNTING

For some dashboards, the hook-and-loop tape included with

your detector might be best for mounting. Follow these steps

to use the hook-and-loop tape.

1. Use a damp cloth to clean the bottom of the detector and

the dashboard. Let both surfaces dry.

Note:

The tape’s adhesive might not stick to a surface

treated with vinyl cleaner or protectant.

2. Remove the backing from one side of the tape and stick

the tape to the bottom of the detector.

Note:

Do not place the hook-and-loop tape over the

detector’s serial number.

Serial Number

Hook-and-Loop

Tape

On a curved dashboard, cut the supplied strip in half and

use one strip on each side of the bottom of the detector.

3. Remove the backing from the other side of the tape and

press the detector onto the dashboard.

WINDSHIELD MOUNTING

The supplied suction-cup windshield bracket lets you easily

mount the detector on the windshield.

Caution:

Do not use the bracket in a vehicle that has a plastic

coating on the windshield designed to protect passengers dur-

ing an accident. If you use the bracket on this type of wind-

shield, you might permanently mar the windshield’s surface.

1. Align the groove in each suction

cup with the slots in the wind-

illus of suction cup

shield bracket and slide the suc-

installation in

tion cups out until they lock into

place.

windshield bracket

2. Clean the selected windshield

area, position the bracket on the

windshield, and press firmly on

each suction cup to secure it in

place.

3. Slide the detector onto the base

plate until it snaps into place.

To level the detector, press the

bracket release button to remove the

detector from the bracket. Then bend

the bracket.

illus of bracket

release button

location

CONNECTING POWER

Caution:

•

Use only the supplied power cord. If your power cord is lost

or damaged, you can order a replacement cord from your

local RadioShack store.

•

Before plugging the power cord’s cigarette-lighter plug into

your vehicle’s cigarette-lighter socket, make sure the plug’s

tip is screwed firmly onto the plug. See “Replacing the

Fuse” on Page 27 for more information about the cigarette-

lighter plug.

•

Unplug the power cord’s cigarette-lighter plug from your

vehicle’s cigarette-lighter socket when you turn off the igni-

tion. This prevents your vehicle’s battery from being drained

if you leave the detector on when you turn off the ignition.

Plug the supplied power cord’s barrel plug into the detector’s

power jack. Then plug the cord’s cigarette-lighter plug into

your vehicle’s cigarette-lighter socket.

Note:

If the detector does not operate when you turn it on,

remove the cigarette-lighter plug from your vehicle’s socket

and check the socket for ashes and other debris. Also check

the fuse in the cigarette-lighter plug and your vehicle’s fuse

block (see “Replacing the Fuse” on Page 27).

DETECTOR OPERATION

TURNING THE DETECTOR ON AND OFF

PWR

To turn on the detector, press

The detector sounds a distinctive alert and displays the indica-

tors for each alert type as a self test, in this order. (The VG-2

indicators only sound/appear if the feature is selected. See

“Setting the VG-2 Option” on Page 14.)

Alert Type

Audible Alert

Visual Alert

Low steady

High trill

and yellow LED

and red LED

Medium warble

None

and yellow/red LEDs

Safety

and red LED

Laser

VG-2

None

–

All features selected are stored in memory. Each time a button

is pressed, one beep confirms the feature is on and two beeps

confirm the feature is off.

See “Receiving and Identifying Alert Signals” on Page 15 for

more information about alerts.

PWR

To turn off the detector, press

ADJUSTING THE VOLUME

To adjust the detector’s volume, hold down PWR until the vol-

ume reaches the desired level, 1–4 (1 is the lowest level).

DEMONSTRATING ALERTS

To familiarize yourself with the different alerts your detector

sounds, you can run a demonstration. To start the demonstra-

tion, press and release MUTE and CITY at the same time with

the detector turned on. The detector demonstrates the alerts

for X, K, Ka, safety warning, laser, and VG-2 (if selected), in

that order. These audible and visual alerts sound and display.

Alert Type

Audible Alert

High trill

Visual Alert

and yellow LED

and red LED

Low steady

Medium warble

and yellow/red LEDs

Safety

Low ascending/descending

and red LED

–

Laser

VG-2

High-low

4-tone ascending

To stop the demonstration, press PWR.

MUTING ALERTS

While a radar, laser, or safety warning alert is sounding, you

can press MUTE to temporarily silence the detector for the cur-

rent alert and any new alert that it receives within 20 seconds.

Visual alerts are not affected.

USING AUTO QUIET

Auto Quiet reduces the selected audio level to a minimum

level about 5 seconds after it detects a radar signal. The audio

alert sounds at the minimum level for any new signal received

within 20 seconds. VG-2 or laser alerts are not affected.

To turn on Auto Quiet, press MUTE when the detector is not

sounding an alert. The detector beeps once and briefly dis-

plays A, then returns to Hor C.

To turn off Auto Quiet, press MUTE when the detector is not

sounding an alert. The detector beeps twice

SELECTING THE CITY AND HIGHWAY

MODES

Your detector’s City mode is designed to reduce annoying

false alerts triggered by automatic door openers, intrusion

alarms, and other devices that share frequencies with police

radar.

Note:

City mode has no effect on laser or VG-2 operation.

To select the City mode, press CITY once. The detector beeps

once and displays C. If the detector receives a weak speed/

safety radar signal in City mode, it beeps twice, then remains

quiet unless the signal becomes very strong. If the signal

strength increases, the detector again beeps twice.

To cancel the City mode, press CITY a second time. The detec-

tor beeps twice and displays H. The highway mode provides

maximum alert response for open-road driving.

SETTING THE VG-2 OPTION

VG-2 is a system used by some law enforcement agencies to

detect the use of radar detectors in vehicles. The VG-2 system

detects the weak radio signals used in radar detectors. Your

radar detector can sense a VG-2 system and shift its operating

frequencies out of the range detected by VG-2, making your

radar detector essentially invisible to this system.

To turn on the VG-2 option, hold down MUTE for 2 seconds.

Press CITY to engage or cancel. –appears when the detection

mode is engaged. Press PWR to exit.

Notes:

•

Your detector does not detect speed radar when VG-2 has

been detected.

To use the VG-2 option, you must turn it on each time you

turn the detector on.

RECEIVING AND IDENTIFYING ALERT

SIGNALS

Your detector gives different audible and visual alerts for each

signal. In addition, the alert tone pulse rate increases with sig-

nal strength and the detector displays a digit from 1 to 9 to

indicate the signal strength (1 is weakest and 9 is strongest).

When your detector senses instant-on radar, it sounds an

intense, 3-second tone and displays P.

Safety Radar Alerts

Your radar detector detects all safety radar including the new

Safety Warning System. This system provides advanced

warning of hazards and lets you respond appropriately to

potentially dangerous conditions.

Note:

Not all areas have Safety Warning System transmitters.

Your radar detector only alerts you to hazards if the area you

are in has transmitters sending signals.

When your radar detector encounters safety radar, it sounds a

distinctive tone and displays the signal strength. In addition,

your radar detector displays S.

Laser Audio/Visual Alerts

When your radar detector detects a laser signal from ahead or

behind, the laser audio sounds and the radar detector displays

L for as long as the signal is present (for a minimum of 3 sec-

onds).

Any laser alert, regardless of duration, requires immediate

action! If you are the targeted vehicle, a laser gun can often

determine your speed within seconds after you receive an

alert. However, if you are traveling near or behind the targeted

vehicle and receive an alert, you should have time to respond.

RESETTING THE DETECTOR

The detector keeps the audio level, city/highway mode, mute

mode, auto quiet mode, VG-2 option, and on or off setting in

memory when power is removed. When you reapply power, it

returns to these same settings.

To reset the detector to its factory default settings, unplug the

detector’s power cord from the cigarette-lighter socket, hold

down PWR and MUTE, plug in the power cord, wait for the

detector to beep twice, then release PWR and MUTE. The

detector turns off the auto quiet and VG-2 options, returns to

the highway mode, and sets the volume to its maximum level.

SAFETY LIGHT

You can power the Safety Light from your vehicle’s battery

power (using the supplied DC power cord), or from six C bat-

teries (not supplied).

Torch Bulb

Red Flasher

Fluorescent

Lamp

Amber Flasher

Six C Batteries

USING VEHICLE BATTERY POWER

1. Plug the supplied DC power cord’s barrel plug into the

Safety Light’s D.C. 12V jack, located on the side of the

Safety Light between the red flasher and the fluorescent

lamp.

Caution:

The supplied DC power cord supplies at least

12 volts and delivers at least 600 mA, and has a center

positive plug that properly fits the Safety Light’s D.C. 12V

jack. Using a power cord that does not meet these specifi-

cations could damage the Safety Light or the power cord.

2. Unplug your vehicle’s cigarette-lighter and plug the large

end of the DC power cord into the cigarette-lighter socket.

INSTALLING/REPLACING BATTERIES

You can power the Safety Light using six C batteries (not sup-

plied). We recommend alkaline batteries, such as Cat. No. 23-

551.

You can also use rechargeable nickel-cadmium batteries, such

as RadioShack Cat. No. 23-124, but you must charge them for

10 hours before using them (see “Charging Rechargeable Bat-

teries” on Page 20).

Cautions:

•

Use only fresh batteries of the required size and recom-

mended type.

•

Do not mix old and new batteries, different types of batteries

(standard, alkaline, or rechargeable), or rechargeable bat-

teries of different capacities.

If you use alkaline batteries, do not set the Safety Light’s

bottom switch to the bottom (charging) position with the DC

power cord connected.

Follow these steps to install batteries in the Safety Light.

1. Slide the battery compartment cover in the direction of the

arrow marked on it and carefully lift it open.

2. Insert six C batteries into the compartment as indicated by

the polarity symbols (+ and –) marked inside.

3. Replace the cover.

When the lights dim, recharge or replace the batteries.

Cautions:

•

If you do not plan to use the Safety Light for a week or

more, remove the batteries. Always remove old or weak

batteries. Batteries can leak chemicals that can destroy

electronic parts.

•

Dispose of old batteries promptly and properly. Do not burn

or bury them.

•

At the end of a nickel-cadmium battery’s useful life, it must

be recycled or disposed of properly. Contact your local,

county, or state hazardous waste management authorities

for information on recycling or disposal programs in your

area. Some options that might be available are: municipal

curbside collection, drop-off boxes at retailers such as your

local RadioShack store, recycling collection centers, and

mail-back programs.

CHARGING RECHARGEABLE

BATTERIES

You can charge rechargeable batteries inside the safety light

using vehicle battery power (using the supplied DC power

cord) or standard AC power (using an optional AC adapter,

such as Cat. No. 273-1653). It takes about 10 hours to fully

charge the batteries. You can use the Safety Light while charg-

ing it, but this increases the charging time to about 20 hours.

Warning:

Do not connect a power cord to the Safety Light’s

D.C. 12V jack if you installed non-rechargeable batteries (stan-

dard, extra-life, or alkaline). Non-rechargeable batteries

become hot and can even explode if you try to recharge them.

Using Vehicle Battery Power

Caution:

The supplied DC power cord supplies at least 12

volts and delivers at least 600 mA, and has a center positive

plug that properly fits the Safety Light’s D.C. 12V jack. Using a

power cord that does not meet these specifications could dam-

age the Safety Light or the power cord.

1. Plug the supplied DC power cord’s barrel plug into the

Safety Light’s D.C. 12V jack.

2. Unplug your vehicle’s cigarette-lighter and plug the large

end of the DC power cord into the cigarette-lighter socket.

3. Set the Safety Light’s bottom switch to the bottom (charg-

ing) position. The charging indicator lights steadily.

Using AC Power

Caution: You must use an AC adapter that supplies at least

12 volts and delivers at least 600 mA. Its center tip must be set

to positive and its plug must fit the Safety Light’s D.C. 12V jack.

The recommended adapter meets these specifications. Using

an adapter that does not meet these specifications could dam-

age the Safety Light or the adapter.

1. Set the adapter’s voltage switch to 12V.

2. Attach the AC adapter’s 5.5 mm outer diameter/2.1 mm

inner diameter barrel plug, aligning + with TIP, then plug it

into the Safety Light’s D.C. 12V jack.

3. Plug the other end of the adapter into a standard AC out-

let.

4. Set the Safety Light’s bottom switch to the bottom (charg-

ing) position. The charging indicator lights steadily.

OPERATION

Cautions:

•

Do not immerse the Safety Light in water.

Keep the lenses clean for brighter, more intense light.

Do not turn on the fluorescent circuit without a tube

installed.

•

Turn off the Safety Light when you finish using it.

To operate the safety light, slide the function switches to the

desired positions.

Switch Position

Function

Torch Bulb Lights Steadily

Off

Top

Middle

Top

Fluorescent Lamp Lights

Steadily

Bottom

Red/Amber Alternately

Flash

Top

Middle

Off

Bottom

Red Only Flashes

Off

Top

Bottom

Charging

REPLACING THE BULBS

Fluorescent Lamp

1. Press the head cap release button, then remove the head

cap, yellow ring, and transparent cover.

2. Twist both metal end caps on the tube so the pins line up

with the slots in the bulb holders, then remove the tube.

Caution:

Twisting the tube itself could break the tube and

cause injury.

3. Replace the tube with a new 9-inch 6-watt tube.

4. Replace the transparent cover, yellow ring, and head cap.

Torch Bulb

1. Press the head cap release button, then remove the head

cap.

2. Pull out the bulb and replace it with a new 8.63 volt, 0.5

amp bulb.

3. Replace the head cap.

Red Flasher Bulb

1. Press the head cap release button, then remove the head

cap, yellow ring, and red flasher cover.

2. Unscrew the bulb, remove it, and replace it with a new 9

volt, 0.3 amp bulb.

3. Insert the red flasher cover’s tab into the slot in the case

and replace the cover.

4. Replace the yellow ring and the head cap.

Amber Flasher Bulb

1. Open the battery compartment cover and remove the bat-

teries, if necessary.

2. Use a Phillips screwdriver to unscrew the two screws,

then lift off the end cap.

3. Pull off the yellow ring and amber flasher cover.

4. Unscrew the bulb and replace it with a new 9 volt, 0.3 amp

bulb.

5. Insert the amber flasher cover’s tab into the slot in the

case and replace the cover.

6. Replace the yellow ring.

7. Align the screw holes in the end cap with those in the

case, replace the end cap, and secure it with the screws.

TROUBLESHOOTING

If you have problems operating your radar/laser detector, the

suggestions in this section might help. If you cannot solve the

problem after trying these suggestions, take your detector to

your local RadioShack store for assistance.

If the detector does not turn on:

•

Be sure all power connections are secure.

Check the fuse that controls power to the cigarette-lighter

socket. See your vehicle’s owner’s manual.

•

Check the fuse in the cigarette-lighter plug. See “Replacing

the Fuse” on Page 27.

The cigarette-lighter socket might be dirty. Clean it to give a

good, clean connection.

Caution:

Do not place any metal object other than the

cigarette lighter or a cigarette-lighter plug in the cigarette-

lighter socket. Doing so could blow a fuse in your vehicle

or cause the metal object to become very hot.

If the detector gives a false alert when the vehicle hits

bumps in the road:

•

Check the power connections.

If the detector gives a false alert when you use accesso-

ries such as power windows, motorized mirrors, brakes,

and so on:

•

Check the vehicle’s electrical system, including the main

battery cable and alternator connections.

•

Install a filter capacitor (1,000 µf, 35 volts, such as Cat. No.

272-1032) on the back of the cigarette-lighter socket,

across the power connections.

If the detector performs the power on self-test (see “Turn-

ing the Detector On and Off” on Page 11), but does not

respond to radar signals when you see a police car:

•

A police car might not be equipped with radar, or might be

using instant-on radar and not have the radar gun triggered

(see the separate booklet Questions and Answers About

Vehicle Speed Detection).

•

Police might be using VASCAR-type speed detection (see

the separate booklet Questions and Answers About Vehicle

Speed Detection).

If the detector has poor laser detection range:

•

Be sure the laser detection lenses are not blocked.

Use lens-cleaning solution to clean the laser detection

lenses and the windshield.

REPLACING THE FUSE

If the detector stops operating, check the fuse in the DC power

cord’s cigarette-lighter plug. If it has blown, follow these steps

to replace it with a 2-Amp, 1¹/⁴× /4 mm, fast-acting fuse (Cat.

No. 270-1007).

Caution:

Using a fuse that does not meet these ratings or

defeating the fuse protection can damage your detector or the

vehicle’s electrical system.

1. Carefully unscrew the tip of the cigarette-lighter plug.

2. Remove the tip from the cigarette-lighter plug, then

remove the old fuse.

Note:

Take care not to lose the spring inside the holder or

the metal ring.

3. Replace the fuse.

4. Press the cigarette-lighter plug’s tip down into the body,

then screw it back in.

Caution:

Be sure you press the cigarette-lighter plug’s tip

down before screwing it in, or you might damage the plug.

DETECTOR WARRANTY

Limited One-Year Warranty

This product is warranted by RadioShack against manufacturing defects in material and

workmanship under normal use for one (1) year from the date of purchase from Ra-

dioShack company-owned stores and authorized RadioShack franchisees and dealers.

EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES

AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DU-

RATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT

AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBIL-

ITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY

LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR

PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS

WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM

INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR

ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF

RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Some states do not allow the limitations on how long an implied warranty lasts or the ex-

clusion of incidental or consequential damages, so the above limitations or exclusions

may not apply to you.

In the event of a product defect during the warranty period, take the product and the Ra-

dioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack

will, at its option, unless otherwise provided by law: (a) correct the defect by product repair

without charge for parts and labor; (b) replace the product with one of the same or similar

design; or (c) refund the purchase price. All replaced parts and products, and products on

which a refund is made, become the property of RadioShack. New or reconditioned parts

and products may be used in the performance of warranty service. Repaired or replaced

parts and products are warranted for the remainder of the original warranty period. You

will be charged for repair or replacement of the product made after the expiration of the

warranty period.

This warranty does not cover: (a) damage or failure caused by or attributable to acts of

God, abuse, accident, misuse, improper or abnormal usage, failure to follow instructions,

improper installation or maintenance, alteration, lightning or other incidence of excess

voltage or current; (b) any repairs other than those provided by a RadioShack Authorized

Service Facility; (c) consumables such as fuses or batteries; (d) cosmetic damage; (e)

transportation, shipping or insurance costs; or (f) costs of product removal, installation,

set-up service adjustment or reinstallation.

This warranty gives you specific legal rights, and you may also have other rights which

vary from state to state.

RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600,

Fort Worth, TX 76102

We Service What We Sell

3/97

SAFETY LIGHT WARRANTY

Limited Ninety-Day Warranty

This product is warranted by RadioShack against manufacturing defects in material and

workmanship under normal use for ninety (90) days from the date of purchase from Ra-